Tuscany TUS1500 User Manual

TUS1500

Tuscany

1

INDEX

WARNINGS AND RECOMMENDATIONS 2

COMPLIANCE DECLARATIONS 3

RANGE AND SIZES 3

ELECTRICITY SUPPLY 3

INSTALLATION 4

INSTRUCTIONS FOR UNINSTALLING THE RADIATOR 5

INSTRUCTIONS FOR USE 6

MAINTENANCE 11

WARRANTY 12

DISPOSAL 13

POSSIBLE PROBLEMS 13

TECHNICAL CHARACTERISTICS 13

2

WARNINGS AND RECOMMENDATIONS

When using the radiator, follow only the instructions found in this manual. Keep this
instruction manual for the entire life of the product, for any further consultation.

It’s strictly forbidden to use other kind of information that are not included in the following sheet
and supplied manual, both of them have to be preserved during the use of the radiator to solve
any doubts about it.

The radiator must not be used by people (children included) whose physical, sensorial or mental
skills are reduced or lack of experience, knowledge, unless they have taken benet from, through
a person responsible of their safety, surveillance or instructions concerning the use of the
radiator. Children must be supervised in order they don’t play with the radiator.

The radiator must be installed in accordance with I.E.E. regulations, the control panels can not
be used or touched from a person inside the shower or bathtub, and must not be installed
immediately under a power plug.

In the power distribution network, in accordance with the installation rules, must be provided a
omnipolar switch which assures complete interruption of current in conditions of overvoltage
category III.

For the connections without the plug assembled by the manufacturer , please address to a
qualied professional. Please respect the colours of the cables for the connection.

The radiator has been conceived to heat a room. It must not be adopted for other uses.

It is dangerous to modify or to alter in any way the radiator characteristics.

Leave at least 50 cm of space between the radiator and any inammable objects.

If the electrical cord is damaged, it must be replaced by the manufacturer or an authorized service
assistant in order to avert any risk.

Do not use the radiator if the control panel (display) is damaged; in case of technical problems ,
contact your retailer, distributor or installer.

Do not lean against or climb on the radiator and do not touch the radiator with wet or damp
hands and feet, it is dangerous for your safety.

Do not insert or place any item inside the radiator.

Do not immerse in any liquid.

Do not allow the supply cable to come into contact with any heated surfaces during operation.

Do not use the appliance if it is damaged.

The materials used for the packaging of the radiator are recyclable. It is recommended to dispose
these materials in the appropriate disposal unit.

3

COMPLIANCE DECLARATIONS

The manufacturer declares under its own responsibility that the radiator has been designed and
constructed in compliance with the following guidelines:

LCIE

ÉLECTRICITÉ

PRODUCT RANGE AND SIZES

Model

| Width (mm) | Height (mm) | Depth (mm) | Weight (Kg)

TUS1500

| 318 | 1866 | 100 | 15

INSTALLATION

THIS UNIT MUST BE INSTALLED VERTICALLY AND WITH THE CONTROLS AT THE BOTTOM.

This radiator is designed to be connected to a 230V/240V system. The supply must be adequate
for the input of the appliance and it must be connected via a fused, double pole, switched, (hav­ing a contact separation of at least 3mm in each pole), exible cable outlet and tted with a 3
Amp fuse. The radiator must be connected in accordance with the latest IEE Regulations and t­ted by a competent electrician.

IMPORTANT: When installed in a bathroom, the unit must NOT be connected via a plug and
socket. The radiator must also be located in the appropriate zone of the bathroom, in accordance
with Section 601 of the Wiring Regulations BS 7671:1992 (Amendment 10983).

NOTE: This Class II appliance does NOT require Earthing. The radiator is tted with a black pilot
wire for connection to a Building Management System. If this pilot wire is not used it is absolutely
essential that it is isolated.

4

CORRECT POSITIONING OF THE RADIATOR

Unpack the radiator and place it carefully on the ground,
using the polystyrene as protection. Make sure that the
radiator and its power cable have not been damaged
during transportation.

Do not use the radiator if it’s damaged.

During the installation ensure that the radiator is not
plugged in. Ensure that the home voltage corresponds to
the Voltage indicated on the radiator (220V – 240V). For
easy installation, your radiator is equipped with an
installation kit containing 4 brackets, 8 screws, 8 plastic
screw anchors.

1. Drill the 8 holes (g.1) with a diameter of 6 mm and
minimum depth of 5 cm. Insert the plastic screw
anchors into the holes.

2. Fix the upper and lower brackets at the wall, using the
given screws. In this phase do not tighten up
completely the lower brackets.

INSTALLATION

Safety precaution: before and during the installation, make sure that the radiator is not
connected to the electricity supply. The radiator must be installed vertically.

The radiator must be tted at least 100mm from the oor.

The radiator can not be installed above a power point and must be positioned at least at 15 cm
from any side obstacle (shelves, furniture, etc…).

The radiator must be positioned at least at a frontal distance of 50 cm from any objects or
furniture.

95

1540

100
min

g.1