Turnigy AE-20A, AE-25A, AE-30A User Manual

User Manual of AE-20A、、、、 25A、、、、 30A Electronic Speed
Controller (ESC)

Thanks for purchasing our Electronic Speed Controller (ESC). High power system
for RC model can be very dangerous, so we strongly suggest you read this manual
carefully. In that we have no control over the correct use, installation, application,
or maintenance of our products, no liability shall be assumed nor accepted for
any damages, losses or costs resulting from the use of the product. Any claims
arising from the operating, failure or malfunctioning etc. will be denied. We
assume no liability for personal injury, property damage or consequential
damages resulting from our product or our workmanship. As far as is legally
permitted, the obligation to compensation is limited to the invoice amount of the
affected product.

Features :

• High performance microprocessor brings out the best compatibility with all kinds of
motors and the higher driving efficiency,start smoothly,suitable for most brushless
motor on market.

• Imported low impedance capacitors,providing good anti-jamming capability,greatly
reduce the possibility the loss of control.

• Supported motor speed (Maximum): 190000rpm(2 poles), 63000rpm (6 poles),
34000rpm(14poles)

• Throttle range can be configured to be compatible with all transmitters currently
available on market
Smooth,linear,quick and precise throttle response.

• With Super-Soft and Govener Mode for helicopter,compatible with Fixed-wing aircraft
and Helicopter.

• With protected over-temperature function,ensure the safe of using ESC and providing
good anti-jamming capability.

• With the design of cooling fins,decrease using temperature.

• The size is small , proper and easy for installation.

Direction for use:

• The range of input voltage:5.5V-16.8V(Lipo 2-4cells/Nimh 6-12cells).Don't surpass
voltage to use ,otherwise it will break the product.

• The power should be connected in correct way .Red is anode and black is cathode.

• Setting for high throttle response speed,

current will be increased in expedite

instantaneous.

•

• •

• With continuous heavy current working,it needs the heat output of ESC goes better.

Wiring Diagram : Attention to the

anode and cathode of the power and connection the

power for testing after checked,the wrong connection will break the controller.

Receiver
Battery ＋＋＋＋

1

Battery －
Red
Black

Brushless

Motor

Electronic Speed Controller

BRUSHLESS MOTOR

For normal start process direction:

Start throttle ,the motor starting
If haven't move
the throttle,the ESC will emit the tone begin to report the function of setted menu

Start transmitters and move the throttle stick to
the bottom position

Connection the ESC to the battery ,a special tone 123.......(ding-ding-ding),that means the connection is ok.

Default:

1. Ding (No brake)

2. Ding-Ding (Medium Timing)

3. Ding-Ding(Medium cut-off threshold)

4. .Ding (Fixed-Wing)

5. Ding (Normal throttle response)

After checking the connection is ok,start transmitters and move the throttle stick to the
bottom position,then the ESC connection the power.
After connection the ESC to the motor,a special tone“♪1 2 3”------ “（ding – ding –

ding）”,that means the self-testing of the ESC is normal.At this moment move the throttle
stick to the top position,the motor can start normally.
If the throttle is still in the bottom position after self-testing is ok ,the ESC will emit the tone
to report the function of seted menu.
ESC emits 5 times "Ding"tone,each time of "Ding" means the match choose with 5
functions menu(please see the concrete function matches function setting form),it can
check whether the function setting form is in accord with the setting or not.

Throttle range setting:

(Attn ! For the first time use or the ESC with other transmitters to use ,it need to re-

setting the

throttle range,other time needn't) .

Proposal set throttle range for the first time use ,after finished ,the throttle linear will be
more smoothly..

The method of setting

1 2 3 4 5 6 7

Start transmitters and move the throttle stick to
the top position

Haven't cut off the power,it will continue to enter other functions set(

Connection the ESC to the battery ,a special tone♪123......♪12345(ding-ding-ding) emits,that means the

connection is ok.

"Ding-Ding-Ding",confirm tone of the top position of throttle

2