Turin Networks CMG Router Quick Start Manual

CMG Router

QUICK START GUIDE

Part Number: 002-0142-0230

Product Release: 2.91

November 2008

Copyright 2008 Turin Networks Inc. All rights reserved.

The information presented in this manual is subject to change without notice and does not represent a
commitment on the part of Turin Networks Inc. The hardware and software described herein are furnished
under a license or non-disclosure agreement. The hardware, software, and manual may be used or copied only
in accordance with the terms of this agreement. It is against the law to reproduce, transmit, transcribe, store
in a retrieval system, or translate into any medium - electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise - any part of this manual or software supplied with the CMG Service card for any
purpose other than the purchaser’s personal use without the express written permission of Turin Networks
Inc.

Adit and the Turin Networks logo are registered trademarks of Turin Networks Inc. All other brand or product
names are trademarks or registration trademarks of their respective companies or organizations.

Supporting Software Versions:

Adit 600 Controller Release 9.7.1

CMG Router Release 2.91

Corporate Contact Information:

Turin Networks, Inc.
1415 North McDowell Blvd.
Petaluma, CA 94954
Phone: [phone]
Fax: [phone]

www.TurinNetworks.com

Turin Technical Assistance Center:

E-mail: [e-mail]
Phone (US): 1-800-887-4638
Phone (International/Direct): 1-707-665-4355

QUICK START GUIDE

In this Guide

 Installation

 Basic Setup

 Basic VoIP Setup

 Fax and Modem Setup

 PPP Internet Connection and Public IP Address

Routing

 Frame Relay Internet Connection and Public IP

Address Routing

 Back-to-Back with PPP

 Back-to-Back with Multi-Link PPP

 Back-to-Back with Frame Relay

Quick Start Guide

Installation

Installation

Installation of the CMG Router card into the Adit 600 chassis.

z Unit can be on or off

z CMG Router card will work in any slot

z Slide card into slot until fully seated

z CMG Router has completed its boot cycle when CRD light is solid

The following setups are all executed with CLI

NOTE: Configuration can be done with the following CLI commands or

with the Router Menu-Driven Software.

Basic Setup

Command Description

set {ds0-addr} type data Confirm DS0 is set to type data.

ds0-addr = {slot:port:channel} of DS0
Example: set a:1:1-24 type data

connect {slot:port:trunk}
{slot:port:channel}

set {router-addr} proxy
{disable|enable}

set {slot:port} up Set Router LAN as In-Service. Example: set 6:1 up

telnet {router_card-addr} Telnet to Router card.

Local and Remote Profile Setup

reinitialize To enable any configuration changes, the card must be

Cross-connect T1 to router card.
Example: connect a:1:1-24 6:1:1 (router in slot 6)

Disable/enable router proxy.
router-addr = {slot:port}| of router card.
Example: set 6:1 disable.

router_card-addr = {slot} location of router card
Example: telnet 6 (if earlier than 3.0 release {slot:port} must
be used)

reinitialized.

4 CMG Router - Release 2.91

Quick Start Guide

Adit 600 Implementation in VoIP Application

Basic VoIP Setup

Basic VoIP Setup

This example is with an Adit 600 with the following cards installed:

z Controller Card (4.0 or higher)

z CMG Router Card, 1.0 or higher (example - slot 6)

z 3 FXS Cards, 1.03 or higher (example - slots 1, 2 and 3). Cards are configured for

Loop Start POTS lines.

Overview

z Adit 600: the DS0s supporting the bundled service delivery will be cross-

connected to the CMG card

z Adit 600: the CMG voice channels are connected to the FXS channels

z Adit 600 CMG: the VoIP parameters and data parameters are configured

z Adit 600 uses endpoint prefix "aaln" and endpoint suffix "1-48" i.e. channel 1

would be suffix "1", channel 5 would be suffix "5"

CMG Router - Release 2.91 5

Quick Start Guide

Basic VoIP Setup

Command Description

set local off

disconnect a:1

disconnect 1

disconnect 2

disconnect 3

disconnect 6

set a:1 up

set a:1 fdl none

set a:1 lbo 1

set a:1 framing esf

set a:1 id "TUR DS1# A:1"

set a:1 linecode b8zs

set a:1 loopdetect on

Set the controller to use CLI commands

Disconnect all connections to the T1-1 on the
Controller (slot a)

Disconnect all connections to the FXS card in slot 1

Disconnect all connections to the FXS card in slot 2

Disconnect all connections to the FXS card in slot 3

Disconnect all connections to the router card in slot 6

Set the T1 on the controller up

Disable FDL output messages on the DS1

Set the DS1 Line Build Out to 0-133 feet

Set the DS1 to Extended Superframe (ESF) framing

Set the DS1 ID to "TUR DS1# A:1"

Set the DS1 line coding to B8ZS.

Enable the detection of CSU loop code on the DS1

set a:1:all type data

set a:2 down

set clock1 a:1

set clock2 internal

set a:2 up

connect a:1:1-24 6:1:1

connect 6:1:1:1-8 1:1-8

connect 6:1:1:9-16 2:1-8

connect 6:1:1:17-24 3:1-8

set verification off

Set the T1-1 of the Controller, Type to Data

Set the T1-2 as Out-of-Service

Set primary master transmit clock source

Set secondary clock source

Set the T1-2 as In-Service

Connect Data DS0s to the CMG card

Connect CMG voice ports to FXS ports

Connect CMG voice ports to FXS ports

Connect CMG voice ports to FXS ports

Disable verification prompts

6 CMG Router - Release 2.91

Quick Start Guide

Basic VoIP Setup

Command Description

set 6:1:1 encapsulation ppp

set 6:1:1 up

set 6:1 ip address {ip-addr}
{mask}

set 6:1 up

add 6 "RemoteAdit" static ip
network {ip-addr} {mask}
{next-hop-ip-addr} 1

set 6 "RemoteAdit" trunk 1

set 6 "RemoteAdit" up

set 6 log last detail

set 6 voip sdpaddress 11.168.1.1

Set Router trunk encapsulations to Point-to-Point
Protocol.

Set Router trunk as In-Service

Set Router IP Address and Subnet Mask

Set Router as In-Service

Set router WAN static ip network. Metric set as 1,
normally indicates a direct network

Set router WAN trunk to port 1

Set router WAN as In-Service

Set the router log to add new entries and display the
log in detail

Set the address value to be used for the origin
and connection lines in the SDP. (May be required
depending on how the LAN and WAN are
configured.)

reset

Reset the CMG card, to apply all configurations

CMG Router - Release 2.91 7

Quick Start Guide

Fax and Modem Setup

Fax and Modem Setup

To configure the fax and modem bypass, the following is required.

z Adit 600, release 8.0

z CMG Router, release 2.3 with G.729 feature enabled (software keyed)

z CMG Router User Interface to configure, CLI configuration not available until

Adit 600 9.0

The following will configure the Fax and Modem

1. Telnet into the Router

> telnet 4
Connected.
Escape character is '^]'.
Attempting Turin Networks CMG connection...
CMG [Wed Jan 2, 2002 0:05:05] (<CR> to login)
Password >******
Select a terminal type...
(<space> or <back-space> to toggle, <CR> to accept)

Terminal: <VT100>

8 CMG Router - Release 2.91

Quick Start Guide

Main
Menu

Profile
Directory
Window

Fax and Modem Setup

2. Select Configuration: <Profile Directory> from the Main Menu, and select

[E

NTER].

3. Select Router CARD <Setup -> and select [E

NTER].

CMG Router - Release 2.91 9

Quick Start Guide

Fax and Modem Setup

4. Select VOIP Configure -> and select [ENTER].

10 CMG Router - Release 2.91

Quick Start Guide

Fax and Modem Setup

5. Tab to Voice Algorithm Settings - > and select [ENTER].

CMG Router - Release 2.91 11

Quick Start Guide

Fax and Modem Setup

6. Verify that the RTP Payload type for nse events is set to a value that other
gateways are using. For most applications this is 100, which is the default
setting. Select [E
any changes.

SC] to exit this window, select <YES> and [ENTER] to save

12 CMG Router - Release 2.91

Quick Start Guide

Fax and Modem Setup

7. Select Voice Channels Configure -> and select [Enter].

CMG Router - Release 2.91 13

Quick Start Guide

Fax and Modem Setup

8. Select a channel or range of channels to configure.

9. Set the Fax setting, from one of the four Fax options:

<none> - a fax call would be treated as a normal voice call. Default.
<bypass> - will cause the line to transmit in G.711 mode, with silence

suppression disabled, on detection of Fax tones.
<T38> - will use T.38 relay if no more than 5 channels are already using T.38
at the same time. Note: there is a limit of six simultaneous T.38 sessions.

<T38reserved> - this line will always be able to use T.38 relay.

Card Maximum # of Channels configured for T.38 Reserved

CMG 6 Channels

CMG-02 12 Channels

14 CMG Router - Release 2.91

Quick Start Guide

Fax and Modem Setup

10. Set the Modem setting, from one of the two Modem options:

<none> - a modem call would be treated as a normal voice call. Default.
<bypass> - upon detection of a modem tone, the line will switch to G.711

mode, with echo cancellation and silence suppression disabled.

11. After the configuration is complete, check the channel status.

On the Main Menu, select Statistics: <VoIP Channel View> and [E

NTER].

12. Press [E

NTER]. The VoIP Channel View window will display.

In the status field, the following can be displayed, regarding Fax and Modem
settings:

Display Setting

Fax Channel is set to T.38

Data Channel is set to Modem Bypass

Active Channel is set for a Voice call

CMG Router - Release 2.91 15

Quick Start Guide

PPP Internet Connection and Public IP Address Routing

PPP Internet Connection and
Public IP Address Routing

Router in Slot 1

ISP Router that provides the Internet connection.

Command Description

set clock1 a:1 Set primary master transmit clock source

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalAdit" "Boulder" Rename the Adit 600 from "LocalAdit" (default)

to "Boulder" (LAN)

rename 1 "RemoteAdit" "wan1" Rename WAN #1 from "RemoteAdit" (default) to

"wan1"

set 1:1 ip address 215.168.21.14

255.255.255.0

add 1 "wan1" static ip network

0.0.0.0 0.0.0.0 1

set 1 "wan1" trunk 1 Set the WAN interface named "wan1" to be

reset 1 Reboot the router, to enable all configurations set

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

mapped to trunk 1

16 CMG Router - Release 2.91

Quick Start Guide

Frame Relay Internet Connection and Public IP Address Routing

Frame Relay Internet Connection and
Public IP Address Routing

Router in Slot 1

ISP Router that provides the Internet connection.

Command Description

set clock1 a:1 Set primary master transmit clock source

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalUnit" "Boulder" Rename the Axxius 800 from "LocalUnit"

(default) to "Boulder" (LAN)

rename 1 "RemoteUnit" "wan1" Rename WAN #1 from "RemoteUnit" (default) to

"wan1"

set 1:1 ip address 215.168.21.14

255.255.255.0

add 1 "wan1" static ip network

0.0.0.0 0.0.0.0 1

set 1:1:1 encapsulation fr Set the encapsulation on trunk 1 to Frame Relay

set 1 lmi annexd Disable LMI to Annex D

set 1 "wan1" trunk 1 Set the WAN interface named "wan1" to be

set 1 "wan1" dlci 101 Set the DLCI number

reset 1 Reboot the router, to enable all configurations set

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

mapped to trunk 1

CMG Router - Release 2.91 17

Quick Start Guide

Boulder

1.1.1.1/24

Denver

2.2.2.1 / 24

24 DS0s

wan1: PPP or Frame Relay

Static Routes

IP

Boulder

1.1.1.1/24

Denver

1.1.1.1/24

Back-to-Back with PPP

Back-to-Back with PPP

The following configuration will set up two Adit Routers back-to-back with PPP.

Boulder Router in Slot 1

Command Description

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalAdit" "Boulder" Rename the Adit 600 from "LocalAdit" (default)

to "Boulder" (LAN)

rename 1 "RemoteAdit" "wan1" Rename WAN #1 from "RemoteAdit" (default) to

"wan1"

set 1:1 ip address 1.1.1.1

255.255.255.0

set 1:1 phy auto Set the Physical Specifications to auto-negotiate

add 1 "wan1" static ip network

2.2.2.0 255.255.255.0 1

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

set 1 "wan1" trunk 1 Set the WAN interface named "wan1" to be

reset 1 Reboot the router, to enable all configurations set

18 CMG Router - Release 2.91

mapped to trunk 1

Quick Start Guide

Back-to-Back with PPP

Denver Router in Slot 1

Command Description

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set clock1 a:1 Set primary master transmit clock source

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalAdit" "Denver" Rename the Adit 600 from "LocalAdit" (default)

to "Denver" (LAN)

rename 1 "RemoteAdit" "wan1" Rename WAN #1 from "RemoteAdit" (default) to

"wan1"

set 1:1 ip address 2.2.2.1

255.255.255.0

set 1:1 phy auto Set the Physical Specifications to auto-negotiate

add 1 "wan1" static ip network

1.1.1.0 255.255.255.0 1

set 1 "wan1" trunk 1 Set the WAN interface named "wan1" to be

reset 1 Reboot the router, to enable all configurations set

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

mapped to trunk 1

CMG Router - Release 2.91 19

Quick Start Guide

Back-to-Back with Multi-Link PPP

Back-to-Back with Multi-Link PPP

The following configuration will set up two Adit 600 Routers back-to-back with Multi­Link PPP.

Boulder Router in Slot 1

Command Description

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

connect a:2:all 1:1:2 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalUnit" "Boulder" Rename the Adit 600 from "LocalUnit" (default)

to "Boulder" (LAN)

rename 1 "LocalUnit" "Boulder" Rename the Adit 600 from "LocalUnit" (default)

to "Boulder" (LAN)

set 1:1:1-2 multilink group 1 Rename the Adit 600 from "LocalUnit" (default)

to "Boulder" (LAN)

rename 1 "RemoteUnit" "wan1" Rename WAN #1 from "RemoteUnit" (default) to

"wan1"

set 1:1 ip address 1.1.1.1

255.255.255.0

add 1 "wan1" static ip network

2.2.2.0 255.255.255.0 1

set 1 "wan1" trunk multilink
group 1

reset 1 Reboot the router, to enable all configurations set

Set the Ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

Set the WAN interface named "wan1" to be
mapped to trunk multilink group 1

20 CMG Router - Release 2.91

Quick Start Guide

Back-to-Back with Multi-Link PPP

Denver Router in Slot 1

Command Description

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set clock1 a:1 Set primary master transmit clock source

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

connect a:2:all 1:1:2 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalUnit" "Denver" Rename the Adit 600 from "LocalUnit" (default)

to "Denver" (LAN)

set 1:1:1-2 multilink group 1 Rename the Adit 600 from "LocalUnit" (default)

to "Boulder" (LAN)

rename 1 "RemoteUnit" "wan1" Rename WAN #1 from "RemoteUnit" (default) to

"wan1"

set 1:1 ip address 2.2.2.1

255.255.255.0

add 1 "wan1" static ip network

1.1.1.0 255.255.255.0 1

set 1 "wan1" trunk multilink
group 1

reset 1 Reboot the router, to enable all configurations set

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

Set the WAN interface named "wan1" to be
mapped to trunk multilink group 1

CMG Router - Release 2.91 21

Quick Start Guide

Boulder

1.1.1.1/24

Denver

2.2.2.1 / 24

24 DS0s

wan1: PPP or Frame Relay

Static Routes

IP

Boulder

1.1.1.1/24

Denver

1.1.1.1/24

Back-to-Back with Frame Relay

Back-to-Back with Frame Relay

The following configuration will set up two Adit Routers back-to-back with Frame Relay.

Boulder Router in Slot 1

Command Description

set clock1 internal Set primary master transmit clock source

set 1 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 1 Disconnect all connections to the router in slot 1

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalAdit" "Boulder" Rename the Adit 600 from "LocalAdit" (default)

to "Boulder" (LAN)

rename 1 "RemoteAdit" "wan1" Rename WAN #1 to "wan1"

set 1:1 ip address 1.1.1.1

255.255.255.0

add 1 "wan1" static ip network

2.2.2.0 255.255.255.0 1

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

set 1:1:1 encapsulation fr Set the encapsulation on trunk 1 to Frame Relay

set 1 lmi disable Disable LMI (Local Management Interface)

set 1 "wan1" trunk 1 Set the WAN interface named "wan1" to be

mapped to trunk 1

set 1 "wan1" dlci 101 Set the DLCI number

reset 1 Reboot the router, to enable all configurations set

22 CMG Router - Release 2.91

Quick Start Guide

Back-to-Back with Frame Relay

Denver Router in Slot 3

Command Description

set 3 default Set Router to default settings

disconnect a:1 Disconnect all connections to the T1 on the

Controller (slot a)

disconnect 3 Disconnect all connections to the router in slot 1

set clock1 a:1 Set primary master transmit clock source

set a:1:all type data Set the T1-1 of the Controller, Type to Data

connect a:1:all 3:1:1 Connect all of T1-1 to the Router that is in slot 1

rename 3 "LocalAdit" "Denver" Rename the Adit 600 from "LocalAdit" (default)

to "Denver" (LAN)

rename 3 "RemoteAdit" "wan1" Rename WAN #1 from "RemoteAdit" (default) to

"wan1"

set 3:1 ip address 2.2.2.1

255.255.255.0

add 3 "wan1" static ip network

1.1.1.0 255.255.255.0 1

set 3:1:1 encapsulation fr Set the encapsulation on trunk 1 to Frame Relay

set 3 lmi disable Disable LMI (Local Management Interface)

set 3 "wan1" trunk 1 Set the WAN interface named "wan1" to be

set 3 "wan1" dlci 101 Set the DLCI number

reset 3 Reboot the router, to enable all configurations set

Set the ethernet IP address, in the conventional IP
address format. (Router LAN)

Adds a static IP network (route) to the WAN
interface

mapped to trunk 1

CMG Router - Release 2.91 23

Quick Start Guide

Back-to-Back with Frame Relay

24 CMG Router - Release 2.91