Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X 7M
■ For T-groove cylinders without mount-
ing accessories
■ Optional accessories for mounting on
other cylindrical housings.
■ One-hand mounting possible
■ Fine adjustment tool and stopper direct-
ly mountable on the sensor
■ Stable mounting
■ Magneto-resistive sensor
■ DC 3-wire, 10…30 VDC
■ NO contact, PNP output
■ Cable connection
Type designation BIM-UNT-AP6X 7M
Ident-No. 4685721
Pass speed
Repeatability
Temperature drift
Hysteresis
Ambient temperature -25…+70 °C
Operating voltage 10…30 VDC
Residual ripple
DC rated operational current
No-load current I
Residual current
Isolation test voltage
Short-circuit protection yes/ Cyclic
Voltage drop at I
Wire breakage/Reverse polarity protection yes/ Complete
Output function 3-wire, NO contact, PNP
Switching frequency 1 kHz
Design Rectangular,UNT
Dimensions 28 x 5 x 6 mm
Housing material Plastic, PP
Active area material Plastic, PP
Tightening torque fixing screw 0.4 Nm
Electrical connection Cables
Cable quality 3mm, Gray, Lif9Y-11Y, PUR, 7
Cable cross section
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP67
MTTF 2283 years acc. to SN 29500 (Ed. 99) 40 °C
Packaging unit 1
Mounting on the following profiles .
Cylindrical design
0
e
ð 10 m/s
ð ± 0.1 mm
ð 0.1 mm
ð 1 mm
ð 10 % U
ss
ð 150 mA
ð 15 mA
ð 0.1 mA
ð 0.5 kV
ð 1.8 V
Suited for E-ChainSystems® acc. to manufacturers
declaration H1063M
3 x 0.14 mm
E N K F
2
Wiring Diagram
Functional principle
Magnetic field sensors are activated by magnetic fields and are used, in particular, for the
detection of the piston position in pneumatic
cylinders. As magnetic fields can permeate
non-magnetizable metals, they detect a permanent magnet attached to the piston through
the aluminium cylinder wall.
Switching state LED,Yellow
Included in delivery cable clip
Edition • 2018-05-22T13:23:49+02:00
1 / 5 TURCK Inc.
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X 7M
Mounting instructions/Description Mounting instructions
Thanks to the mounting lip, the sensor can be insert-
ed into the groove from above with one hand. Mount
the sensors as follows using the patented wing screw:
The wing screw and the female thread feature a left-
hand thread. Two small plastic lips keep the screw in
position, ready-to-install. Turn the screw clockwise.
The screw moves out of the thread and hits the upper
grooves with the wings. The sensor is thus pressed
down and locked in position. A few degrees up to ap-
proximately 1.5 turns of the screw with a slotted screw-
driver (blade width 0.5 mm) or a 1.5 mm Allen key are
sufficient to ensure vibration-proof fastening, depend-
ing on the shape of the slot. A tightening torque of 0.4
Nm is sufficient for safe mounting without damaging the
cylinder. The sensor can now withstand an axial and ra-
dial tensile load of F=100N applied on the cable. A ca-
ble clip is included in the scope of delivery. It enables
smooth cable routing in the groove and ensures that
the cable is fastened as securely as possible. The cor-
responding accessories for mounting on other cylindri-
cal housings must be ordered separately.
Edition • 2018-05-22T13:23:49+02:00
2 / 5 TURCK Inc.
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X 7M
Accessories
Type code Ident-No. Description
KLZ1-INT CLAMP 6970410 Accessories for mounting the sensors BIM-INT and BIM-UNT
on tie-rod cylinders; Cylinder diameter: 32…40 mm; material:
Aluminium; Further mounting accessories for other cylinder
diameters on request
KLZ2-INT CLAMP 6970411 Accessories for mounting the sensors BIM-INT and BIM-UNT
on tie-rod cylinders; Cylinder diameter: 50…63 mm; material:
Aluminium; Further mounting accessories for other cylinder
diameters on request
UNT-STOPPER 4685751
UNT-ADJUSTING
BRACKET
KLRC-UNT1 6970626
4685750
Accessories for finetuning the switchpoint on N T-groove
cylinders; snap-locked in the BIM-UNT fixture; suited for mul-
tiple use; material: plastic
Accessories for finetuning the switchpoint on N T-groove
cylinders; snap-locked in the BIM-UNT fixture; suited for mul-
tiple use; material: metal/plastic
Accessories for mounting on E cylinders; diameter: 8…25
mm; material: PA 6I/6T / nickel silver; Fire-hazard classifica-
tion acc. to UL94 - V2
Edition • 2018-05-22T13:23:49+02:00
3 / 5 TURCK Inc.
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X 7M
Accessories
Type code Ident-No. Description
KLRC-UNT2 6970627
Accessories for mounting on E cylinders; diameter: 25…63
mm; material: PA 6I/6T / nickel silver; Fire-hazard classifica-
tion acc. to UL94 - V2
KLRC-UNT3 6970628
KLRC-UNT4 6970629
KLDT-UNT2 6913351 Accessories for mounting the BIM-UNT sensor on dovetail
Accessories for mounting the BIM-UNT sensor on E round
cylinders; diameter: 63…130 mm; material: PA 6I/6T / nickel
silver; Fire-hazard classification acc. to UL94 - V2
Accessories for mounting the BIM-UNT sensor on E round
cylinders; diameter: 130…250 mm; material: PA 6I/6T / nickel
silver; Fire-hazard classification acc. to UL94 - V2
cylinders; groove width: 7 mm; material: PPS
KLDT-UNT3 6913352
Edition • 2018-05-22T13:23:49+02:00
4 / 5 TURCK Inc.
Accessories for mounting the BIM-UNT sensor on K dove-
tail groove cylinders; groove width: 9.4 mm; material: PPS
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X 7M
Accessories
Type code Ident-No. Description
KLDT-UNT6 6913355
Accessories for mounting on K dovetail groove cylinders;
groove width: 7.35 mm; material: PPS
Edition • 2018-05-22T13:23:49+02:00
5 / 5 TURCK Inc.
Loading...