Turck BIM-UNT-AN6X-0.3-PSG3S Data Sheet
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AN6X-0.3-PSG3S
■ For T-groove cylinders without mount-
ing accessories
■ Optional accessories for mounting on
other cylindrical housings.
■ One-hand mounting possible
■ Fine adjustment tool and stopper direct-
ly mountable on the sensor
■ Stable mounting
■ Magneto-resistive sensor
■ DC 3-wire, 10…30 VDC
■ NO contact, NPN output
■ Pigtail with male end, Ø 8 mm
Type designation BIM-UNT-AN6X-0.3-PSG3S
Ident-No. 4685705
Ident. no. 4685705
Pass speed
Repeatability
Temperature drift
Hysteresis
Ambient temperature -25…+70 °C
Operating voltage 10…30 VDC
Residual ripple
DC rated operational current
No-load current I
Residual current
Isolation test voltage
Short-circuit protection yes/ Cyclic
Voltage drop at I
Wire breakage/Reverse polarity protection yes/ Complete
Output function 3-wire, NO contact, NPN
Switching frequency 1 kHz
Design Rectangular,UNT
Dimensions 28 x 5 x 6 mm
Housing material Plastic, PP
Active area material Plastic, PP
Tightening torque fixing screw 0.4 Nm
Electrical connection Cable with connector, Ø 8 mm
Cable quality 3mm, Gray, Lif9Y-11Y, PUR, 0.3
Cable cross section
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP67
MTTF 2283 years acc. to SN 29500 (Ed. 99) 40 °C
Packaging unit 1
Mounting on the following profiles .
Cylindrical design
0
e
ð 10 m/s
ð ± 0.1 mm
ð 0.1 mm
ð 1 mm
ð 10 % U
ss
ð 150 mA
ð 15 mA
ð 0.1 mA
ð 0.5 kV
ð 1.8 V
Suited for E-ChainSystems® acc. to manufacturers
declaration H1063M
3 x 0.14 mm
E N K F
2
Wiring Diagram
Functional principle
Magnetic field sensors are activated by magnetic fields and are used, in particular, for the
detection of the piston position in pneumatic
cylinders. As magnetic fields can permeate
non-magnetizable metals, they detect a permanent magnet attached to the piston through
the aluminium cylinder wall.
Switching state LED,Yellow
Included in delivery cable clip
Edition • 2018-07-11T22:37:20+02:00
1 / 5 TURCK Inc.
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AN6X-0.3-PSG3S
Mounting instructions/Description Mounting instructions
Thanks to the mounting lip, the sensor can be insert-
ed into the groove from above with one hand. Mount
the sensors as follows using the patented wing screw:
The wing screw and the female thread feature a left-
hand thread. Two small plastic lips keep the screw in
position, ready-to-install. Turn the screw clockwise.
The screw moves out of the thread and hits the upper
grooves with the wings. The sensor is thus pressed
down and locked in position. A few degrees up to ap-
proximately 1.5 turns of the screw with a slotted screw-
driver (blade width 0.5 mm) or a 1.5 mm Allen key are
sufficient to ensure vibration-proof fastening, depend-
ing on the shape of the slot. A tightening torque of 0.4
Nm is sufficient for safe mounting without damaging the
cylinder. The sensor can now withstand an axial and ra-
dial tensile load of F=100N applied on the cable. A ca-
ble clip is included in the scope of delivery. It enables
smooth cable routing in the groove and ensures that
the cable is fastened as securely as possible. The cor-
responding accessories for mounting on other cylindri-
cal housings must be ordered separately.
Edition • 2018-07-11T22:37:20+02:00
2 / 5 TURCK Inc.
Loading...