TURCK BIM-UNT-0,1-UNT-2AP6X3-H1141 Technical data

Download

Page 1

BIM-UNT-0,1-UNT-2AP6X3-H1141 Magnetic Field Sensor – For Pneumatic Cylinders

Features

For T-groove cylinders without mounting

■

accessories Optional accessories for mounting on other

■

cylindrical housings. One-hand mounting possible

■

Fine adjustment tool and stopper directly

■

mountable on the sensor Stable mounting

■

Optimally suited for monitoring two switching

■

points on a cylinder No Y-junction required

■

Magneto-resistive sensor

■

2x NO contacts, PNP output

■

DC 4‐wire, 10…30 VDC

■

Technical data

Wiring diagram

Type

Ident. no. 4685734

Pass speed ≤10m/s

Repeatability ≤ ±0.1mm

Temperature drift ≤0.1mm

Hysteresis ≤1mm

Ambient temperature -25…+70°C

Operating voltage 10…30VDC

Residual ripple ≤10% U

DC rated operational current ≤150mA

No-load current ≤15mA

Residual current ≤0.1mA

Isolation test voltage ≤0.5kV

Short-circuit protection yes / Cyclic

Voltage drop at I

Wire breakage/Reverse polarity protection yes / Complete

Output function 4-wire, NO contact, PNP

Switching frequency 1kHz

Design

Dimensions 30x5x22mm

Housing material Plastic, PP

Active area material Plastic, PP

Tightening torque fixing screw 0.4Nm

Electrical connection Connector,M12 × 1

BIM-UNT-0,1-UNT-2AP6X3-H1141

≤1.8V

Rectangular,UNT

Functional principle

Magnetic field sensors are activated by magnetic fields and are used, in particular, for the detection of the piston position in pneumatic cylinders. As magnetic fields can permeate nonmagnetizable metals, they detect a permanent

BIM-UNT-0,1-UNT-2AP6X3-H1141 | 12/03/2020 06-25 | technical changes reserved

1|4

Page 2

Technical data

Cable quality Ø3mm, Gray, Lif9Y-11Y, PUR, 0.1m

Suited for E-ChainSystems® acc. to manufacturers declaration H1063M

Core cross-section

3x0.14mm

Vibration resistance 55Hz (1 mm)

Shock resistance 30g (11 ms)

Protection class IP67

MTTF 2283years acc. to SN 29500 (Ed. 99) 40

°C

Mounting on the following profiles

Cylindrical design

Power-on indication

 E N K F

LED,Green

Switching state 2 × LEDs,Yellow/Yellow

Included in delivery 2x cable clip

Mounting instructions

magnet attached to the piston through the aluminium cylinder wall.

Mounting instructions/Description

Insert sensor S2 from above; insert sensor S1 laterally in the groove with the tip first, then click-in. Mount the sensors as follows using the patented wing screw: The wing screw features a left-hand female thread. Two small plastic lips keep the screw in position, ready-to-install. Turn the screw clockwise. The screw moves out of the thread and hits the upper grooves with the wings. The sensor is thus pressed down and locked. Use a standard screw driver or a 1.5 mm Allen key to fasten the screw with a quarter turn. A fixing torque of 0.4 Nm is sufficient for safe mounting without damaging the cylinder. The sensor now withstands axial and radial tensile load of F=100N applied on the cable. Cable clips are included in the scope of delivery. They enable smooth cable routing in the groove. Mounting accessories for other cylinder sizes have to be ordered separately.

BIM-UNT-0,1-UNT-2AP6X3-H1141 | 12/03/2020 06-25 | technical changes reserved

2|4

Page 3

Accessories

KLZCD2-UNT 6970418

Mounting bracket for mounting magnetic field sensors for T-grooves on a CleanDesign cylinder with mounting rail

KLZ2-INT 6970411

Accessories for mounting the sensors BIM-INT and BIM-UNT on tie-rod cylinders; Cylinder diameter: 50… 63 mm; material: Aluminium; Further mounting accessories for other cylinder diameters on request

UNT-JUSTAGE 4685750

Accessories for fine-tuning of the switching point on N T-groove cylinders; snap-lock mounting in the BIM-UNT sensor fixture; suited for multiple use; material: Metal/plastic

KLZ1-INT 6970410

Accessories for mounting the sensors BIM-INT and BIM-UNT on tie-rod cylinders; Cylinder diameter: 32… 40 mm; material: Aluminium; Further mounting accessories for other cylinder diameters on request

UNT-STOPPER 4685751

Accessories for finetuning the switchpoint on N T-groove cylinders; snap-locked in the BIM-UNT fixture; suited for multiple use; material: plastic

KLRC-UNT1 6970626

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 8…25 mm; material: PA 6I/6T / nickel silver; fire-hazard classification acc. to UL94

- V2

KLRC-UNT2 6970627

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 25…63 mm; material: PA 6I/6T / nickel silver; fire-hazard classification acc. to UL94

- V2

KLRC-UNT4 6970629

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 130… 250 mm; material: PA 6I/6T / nickel silver; fire-hazard classification acc. to UL94 - V2

KLRC-UNT3 6970628

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 63…130 mm; material: PA 6I/6T / nickel silver; fire-hazard classification acc. to UL94

- V2

KLDT-UNT2 6913351

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width: 7mm; material: PPS

BIM-UNT-0,1-UNT-2AP6X3-H1141 | 12/03/2020 06-25 | technical changes reserved

3|4

Page 4

KLDT-UNT3 6913352

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width:

9.4mm; material: PPS

KLDT-UNT6 6913355

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width: 7.35 mm; material: PPS

BIM-UNT-0,1-UNT-2AP6X3-H1141 | 12/03/2020 06-25 | technical changes reserved

4|4