TURCK BIM-PST-Y1X-0.2-RS4.21T Technical data

BIM-PST-Y1X-0.2-RS4.21T W/KLP80
Magnetic Field Sensor – for pneumatic cylinders

Features

Rectangular, height 16 mm

■

Front active face

■

Plastic, PA12-GF30

■

Magnetic-inductive sensor

■

DC 2-wire, nom. 8.2 VDC

■

Output according DIN EN 60947-5-6

■

(NAMUR)
Pigtail with male end, M12 x 1

■

ATEX category II 2 G, Ex zone 1

■

ATEX category II 1 D, Ex zone 20

■

SIL2 (Low Demand Mode) acc. to IEC 61508,

■

PL c acc. to ISO 13849-1 at HFT0
SIL3 (All Demand Mode) acc. to IEC 61508,

■

PL e acc. to ISO 13849-1 with redundant

Technical data

configuration HFT1

Type

Ident. no. 1057095

Pass speed ≤10m/s

Repeatability ≤ ±0.1mm

Temperature drift ≤0.1mm

Hysteresis ≤1mm

Ambient temperature -25…+70°C

Output function 2-wire, NAMUR

Switching frequency 1kHz

Voltage Nom.8.2VDC

Current consumption non-actuated ≤1.2mA

Actuated current consumption ≥2.1mA

Approval acc. to KEMA 02 ATEX 1090X

Internal capacitance (Ci)/inductance (Li) 150 nF/150 µH

Device marking

Design

Dimensions 23x14x16mm

Housing material Plastic, PA12-GF30

Active area material Plastic, PA12-GF30

Electrical connection Cable with connector,M12 × 1

Cable quality Ø4mm, Blue, LifYY-11Y, PUR, 0.2m

Core cross-section

BIM-PST-Y1X-0.2-RS4.21T W/KLP80

É II 2 G Ex ia IIC T6 Gb / II 1 D Ex ia IIIC
T95 °C Da

(max. Ui = 20 V, Ii = 60 mA, Pi = 130 mW)

Rectangular,PST

2x0.25mm

2

Wiring diagram

Functional principle

Magnetic field sensors are activated by
magnetic fields and are especially suited
for piston position detection in pneumatic
cylinders. Based on the fact that magnetic
fields can permeate non-magnetizable metals,
it is possible to detect a permanent magnet
attached to the piston through the aluminium
wall of the cylinder.

BIM-PST-Y1X-0.2-RS4.21T W/KLP80 | 12/03/2020 06-34 | technical changes reserved

TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: [phone] | Application Support: 1-800-544-7769 | Fax [phone] | www.turck.com

1|3

Technical data

Vibration resistance 55Hz (1 mm)

Shock resistance 30g (11 ms)

Protection class IP67

MTTF 6198years acc. to SN 29500 (Ed. 99) 40

°C

Mounting on the following profiles

Cylindrical design



E

Switching state LED,Yellow

Included in delivery KLP80

Accessories

IMC-DI-22EX-PNO/24VDC 7560003

2-channel isolating switching amplifier
with M12x1 males, for peripheral use,
IP67, zones 2/22, input circuits II(1)
Ex ia, PNP transistor output NO

KLP 80-VA 69654

Mounting on round cylinders; cylinder
diameter 25…80mm; material: Metal
A2 1.4301 (AISI 304); two tie bolts
(material: Metal CuZn, alternatively
metal A2 1.4301 / AISI 304) cylinder
screw M3 x 20; (DIN 912-A20)

KLP 25 MONTAGESET 69653

Mounting on round cylinders; cylinder
diameter 8…25mm; material: Metal
CuZn; two tie bolts (material: Metal
CuZn), cylinder screw M3 x 20

KLP 200-VA 6965302

Mounting on round cylinders; cylinder
diameter 80…200mm material: Metal
A2 1.4301 (AISI 304); two tie bolts
(material: Metal CuZn, alternatively
metal A2 1.4301 / AISI 304) cylinder
screw M3 x 20; (DIN 912-A20)

TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: [phone] | Application Support: 1-800-544-7769 | Fax [phone] | www.turck.com

BIM-PST-Y1X-0.2-RS4.21T W/KLP80 | 12/03/2020 06-34 | technical changes reserved

2|3

Operating Instructions

Intended use

This device fulfills the directive 2014/34/EC and is suited for use in explosion hazardous areas according to EN
60079-0:2012 + A11 and EN 60079-11:2012.Further it is suited for use in safety-related systems, including SIL2 as per IEC

61508.In order to ensure correct operation to the intended purpose it is required to observe the national regulations and
directives.

For use in explosion hazardous areas conform to classification

II 2 G and II 1 D (Group II, Category 2 G, electrical equipment for gaseous atmospheres and category 1 D, electrical equipment for
dust atmospheres).

Marking (see device or technical data sheet)

É II 2 G and Ex ia IIC T6 Gb and É II 1 D Ex ia IIIC T95 °C Da acc. to EN 60079-0, -11

Local admissible ambient temperature

-25…+70 °C

Installation/Commissioning

These devices may only be installed, connected and operated by trained and qualified staff. Qualified staff must have
knowledge of protection classes, directives and regulations concerning electrical equipment designed for use in
explosion hazardous areas.Please verify that the classification and the marking on the device comply with the actual
application conditions.

This device is only suited for connection to approved Exi circuits according to EN 60079-0 and EN 60079-11. Please
observe the maximum admissible electrical values.After connection to other circuits the sensor may no longer be
used in Exi installations. When interconnected to (associated) electrical equipment, it is required to perform the "Proof
of intrinsic safety" (EN60079-14).Attention! When used in safety systems, all content of the security manual must be
observed.

Installation and mounting instructions

Avoid static charging of cables and plastic devices. Please only clean the device with a damp cloth. Do not install the
device in a dust flow and avoid build-up of dust deposits on the device.If the devices and the cable could be subject to
mechanical damage, they must be protected accordingly. They must also be shielded against strong electro-magnetic
fields.The pin configuration and the electrical specifications can be taken from the device marking or the technical data
sheet.

Service/Maintenance

Repairs are not possible. The approval expires if the device is repaired or modified by a person other than the
manufacturer. The most important data from the approval are listed.

BIM-PST-Y1X-0.2-RS4.21T W/KLP80 | 12/03/2020 06-34 | technical changes reserved

TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: [phone] | Application Support: 1-800-544-7769 | Fax [phone] | www.turck.com

3|3