Turck BI1.5-EH6.5K-Y1 Technical data

BI1.5-EH6.5K-Y1 Inductive Sensor
Features
Smooth barrel, Ø 6.5 mm
Stainless steel, 1.4427 SO
DC 2-wire, nom. 8.2 VDC
Output acc. to DIN EN 60947-5-6 (NAMUR)
Cable connection
ATEX category II 1 G, Ex zone 0
ATEX category II 1 D, Ex zone 20
SIL2 (Low Demand Mode) acc. to IEC
61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508,
PL e acc. to ISO 13849-1 with redundant configuration HFT1
Technical data
Type
ID no. 1004600
Mounting conditions Flush
Secured operating distance ≤(0.81×Sn)mm
Correction factors St37 = 1; Al = 0.3; stainless steel = 0.7;
Repeat accuracy ≤2% of full scale
Temperature drift ≤ ± 10 %
Hysteresis 1…10%
Ambient temperature -25…+70°C
Output function 2-wire, NAMUR
Switching frequency 5kHz
Voltage Nom.8.2VDC
Non-actuated current consumption ≥2.1mA
Actuated current consumption ≤1.2mA
Approval acc. to KEMA 02 ATEX 1090X
Internal capacitance (Ci)/inductance (Li) 150 nF/150 µH
Device marking
Design
Dimensions 23.6mm
Housing material Stainless steel, 1.4427 SO
Active area material Plastic, PA12-GF30
End cap Plastic, PP
Electrical connection Cable
Cable quality Ø4mm, Blue, Lif9YYW, PVC, 2m
BI1.5-EH6.5K-Y1
Ms = 0.4
É II 1 G Ex ia IIC T6 Ga/II 1 D Ex ia IIIC T95 °C Da
(max. Ui = 20 V, Ii = 60 mA, Pi = 80 mW)
Smooth barrel,6.5 mm
Wiring diagram
Functional principle
Inductive sensors detect metal objects contactless and wear-free. For this, they use a high-frequency electromagnetic AC field that interacts with the target. Inductive sensors generate this field via an RLC circuit with a ferrite coil.
BI1.5-EH6.5K-Y1 | 22-04-2021 15-50 | Technical modifications reserved
Hans Turck GmbH & Co. KG | 45466 Mülheim an der Ruhr, Germany | T +49 208 4952-0 | F +49 208 4952-264 | more@turck.com | www.turck.com 1|3
Technical data
Core cross-section
2x0.25mm
2
Vibration resistance 55Hz (1 mm)
Shock resistance 30g (11 ms)
Protection class IP67
MTTF 6198years acc. to SN 29500 (Ed. 99) 40
°C
Mounting instructions
Mounting instructions/Description
Distance D 2 x B
Distance W 3 x Sn
Distance T 3 x B
Distance S 1.5 x B
Distance G 6 x Sn
Diameter active
Ø6.5mm
area B
Hans Turck GmbH & Co. KG | 45466 Mülheim an der Ruhr, Germany | T +49 208 4952-0 | F +49 208 4952-264 | more@turck.com | www.turck.com 2|3
BI1.5-EH6.5K-Y1 | 22-04-2021 15-50 | Technical modifications reserved
Operating Instructions
Intended use This device fulfills the directive 2014/34/EC and is suit-
ed for use in explosion hazardous areas according to EN 60079-0:2012 + A11 and EN 60079-11:2012.Further it is suit­ed for use in safety-related systems, including SIL2 as per IEC
61508.In order to ensure correct operation to the intended pur­pose it is required to observe the national regulations and di­rectives.
For use in explosion hazardous areas conform to classification II 1 G and II 1 D (Group II, Category 1 G, electrical equipment
for gaseous atmospheres and category 1 D, electrical equip­ment for dust atmospheres).
Marking (see device or technical data sheet)
Local admissible ambient temperature -25…+70 °C
Installation/Commissioning These devices may only be installed, connected and oper-
Installation and mounting instructions Avoid static charging of cables and plastic devices. Please
Service/Maintenance Repairs are not possible. The approval expires if the device is
É II 1 G and Ex ia IIC T6 Ga and É II 1 D Ex ia IIIC T95 °C Da acc. to EN 60079-0, -11
ated by trained and qualified staff. Qualified staff must have knowledge of protection classes, directives and regulations concerning electrical equipment designed for use in explosion hazardous areas.Please verify that the classification and the marking on the device comply with the actual application con­ditions.
This device is only suited for connection to approved Exi cir­cuits according to EN 60079-0 and EN 60079-11. Please ob­serve the maximum admissible electrical values.After con­nection to other circuits the sensor may no longer be used in Exi installations. When interconnected to (associated) electri­cal equipment, it is required to perform the "Proof of intrinsic safety" (EN60079-14).Attention! When used in safety systems, all content of the security manual must be observed.
only clean the device with a damp cloth. Do not install the device in a dust flow and avoid build-up of dust deposits on the device.If the devices and the cable could be subject to mechanical damage, they must be protected accordingly. They must also be shielded against strong electro-magnetic fields.The pin configuration and the electrical specifications can be taken from the device marking or the technical data sheet.
repaired or modified by a person other than the manufacturer. The most important data from the approval are listed.
Hans Turck GmbH & Co. KG | 45466 Mülheim an der Ruhr, Germany | T +49 208 4952-0 | F +49 208 4952-264 | more@turck.com | www.turck.com 3|3
BI1.5-EH6.5K-Y1 | 22-04-2021 15-50 | Technical modifications reserved
Loading...