turck B1N360V-Q20L60-2Li2-H1151/3GD, B2N45H-Q20L60-2Li2-H1151/3GD Quick Start Manual

Inclinometer
B1N360V-Q20L60-2Li2-H1151/3GD

Type code B1N360V-Q20L60-2Li2-H1151/3GD

Ident no. 1534113

Measuring range 0…360°
Repeatability

Temperature coefficient typical 0.03 °/K
Resolution
Ambient temperature -30…+70 °C

Operating voltage 10…30VDC
Rated insulation voltage
Short-circuit protection yes
Wire breakage / Reverse polarity protection yes/ complete
Output function 5-wire, analog output
Current output 4…20mA

Load resistance current output
Response time 0.1 s

Current consumption 50…105 mA (voltage-dependent)

ð 0.2 % of measuring range |A - B|
ð 0.1 %, after warm-up 0.5 h

ð 0.14 °

in the explosion hazardous area see instruction
leaflet

ð 0.5 kV

2 outputs, one for CW and one for CCW
ð 0.2 kò

Time for the output signal to reach 90% of the ad­justed measuring range

■

ATEX category II 3 G, Ex Zone 2

■

ATEX category II 3 D, Ex Zone 22

■

Rectangular, plastic, PC

■

Compact housing

■

Connection via M12x1 plug connectors

■

12 bit resolution

■

5-wire, 10…30 VDC

■

4 … 20mA analog output for clockwise
(CW) rotation

■

4 … 20mA analog output for counter­clockwise (CCW) rotation

Wiring diagram

Functional principle

The TURCK inclinometers incorporate a mi­cromechanical pendulum, operating on the
principle of MEMS technology (Mikro Elektro
Mechanic Systems).

The pendulum basically consists of two 'plate'
electrodes arranged in parallel with a dielec­tric placed in the middle. When the sensor is
inclined, the dielectric in the middle moves,
causing the capacitance ratio between both
electrodes to change.

The downstream electronics evaluates this
change in capacitance and generates a corre­sponding output signal.

Approval acc. to ATEX declaration of conformity TURCK Ex-12002H

X

Device designation Ex II 3 G Ex nA IIC T5 Gc/II 3 D Ex tc IIIC T85°C Dc

Design rectangular, Q20L60
Dimensions 60 x 30 x 20 mm
Housing material plastic, PC
Connection male, M12 x 1
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP68 / IP69K
MTTF 203 years acc. to SN 29500 (Ed.99) 40 °C

Included in scope of supply Security clip SC-M12/3GD

Edition • 2014-06-17T07:45:37+02:00

1 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [e-mail] ñ www.turck.com

Inclinometer
B1N360V-Q20L60-2Li2-H1151/3GD

Mounting instructions / Description Tilt angle

Adjusting the measuring range via TX1-Q20L60 teach

adapter

Setting the angular range in CW direction:

Move sensor to start position

■

Press and hold Teach-Gnd until the output is set to

■

< 4 mA / 0,1 V (approx. 1 s)

Move sensor to end position

■

Press and hold Teach-Gnd until the output is set to

■

20 mA / 4.9 V (approx. 3 s)

Resetting the angular range:

Press and hold Teach-Gnd until the output is set to

■

12 mA (approx. 6 s)

The working range of angle measurement is set

■

back to 360° degrees (in position "connector outgo-

ing topwards" the sensor provides an output signal

in accordance with 0 ° degree)

Edition • 2014-06-17T07:45:37+02:00

2 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [e-mail] ñ www.turck.com