Turbosound TCX82-R Quick Start Guide

Page 1

TCX82-R / TCX82-R-WH TCX102-R / TCX102-R-WH TCX122-R / TCX122-R-WH TCX152-R / TCX152-R-WH TCX115B-R / TCX115B-R-WH TCX118B-R / TCX118B-R-WH

Weather Resistant Loudspeakers for Installation Applications

Quickstart Guide

Page 2

TCX series Quick Start Guide

Important Safety Instructions

Terminals marked with this symbol carry electrical

current of sufﬁ cient magnitude to constitute risk of electric shock. Use only high-quality commercially-available speaker cables with plugs pre-installed. All other installation or modiﬁ cation should be performed only by qualiﬁ ed personnel.

This symbol, wherever it

appears, alerts you to the

presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufﬁ cient to constitute a risk of shock.

This symbol, wherever it

appears, alerts you to important

operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution

To reduce the risk of electric

shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualiﬁ ed personnel.

Caution

To reduce the risk of ﬁ re or

electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects ﬁ lled with liquids, such as vases, shall be placed on the apparatus.

Caution

These service instructions are

for use by qualiﬁ ed service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualiﬁ ed service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation

openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁ ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories speciﬁ ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU)

and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efﬁ cient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city ofﬁ ce, or your household waste collection service.

LEGAL DISCLAIMER

MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical speciﬁ cations, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA and TC APPLIED TECHNOLOGIES are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC Group’s Limited Warranty, please see complete details online at music-group.com/warranty.

Instrucciones de seguridad

Las terminales marcadas con este símbolo transportan

corriente eléctrica de magnitud suﬁ ciente como para constituir un riesgo de descarga eléctrica. Utilice solo cables de altavoz de alta calidad con clavijas TS de 6,3 mm pre-instaladas (puede adquirirlos en comercios especializados en audio). Cualquier otra instalación o modiﬁ cación debe ser realizada únicamente por un técnico cualiﬁ cado.

Este símbolo, siempre que

aparece, le advierte de la

presencia de voltaje peligroso sin aislar dentro de la caja; este voltaje puede ser suﬁ ciente para constituir un riesgo de descarga.

Este símbolo, siempre que

aparece, le advierte sobre

instrucciones operativas y de mantenimiento que aparecen en la documentación adjunta. Por favor, lea el manual.

Atención

Para reducir el riesgo de

descarga eléctrica, no quite la tapa (o la parte posterior). No hay piezas en el interior del equipo que puedan ser reparadas por el usuario. Si es necesario, póngase en contacto con personal cualiﬁ cado.

Atención

Para reducir el riesgo de

incendio o descarga eléctrica, no exponga este aparato a la lluvia, humedad o alguna otra fuente que pueda salpicar o derramar algún líquido sobre el aparato. No coloque ningún tipo de recipiente para líquidos sobre el aparato.

Atención

Las instrucciones de servicio

deben llevarlas a cabo exclusivamente personal cualiﬁ cado. Para evitar el riesgo de una descarga eléctrica, no realice reparaciones que no se encuentren descritas en el manual de operaciones. Las reparaciones deben ser realizadas exclusivamente por personal cualiﬁ cado.

1. Lea las instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas

las advertencias.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Limpie este aparato con un paño seco.

7. No bloquee las aberturas de

ventilación. Instale el equipo de acuerdo con las instrucciones del fabricante.

8. No instale este equipo cerca de fuentes de calor tales como radiadores, acumuladores de calor, estufas u otros aparatos (incluyendo ampliﬁ cadores) que puedan producir calor.

9. No elimine o deshabilite nunca la conexión a tierra del aparato o del cable de alimentación de corriente. Un enchufe polarizado tiene dos polos, uno de los cuales tiene un contacto más ancho que el otro. Una clavija con puesta a tierra dispone de tres contactos: dos polos y la puesta a tierra. El contacto ancho y el tercer contacto, respectivamente, son los que garantizan una mayor seguridad. Si el enchufe suministrado con el equipo no concuerda con la toma de corriente, consulte con un electricista para cambiar la toma de corriente obsoleta.

10. Coloque el cable de suministro de energía de manera que no pueda ser pisado y que esté protegido de objetos aﬁ lados. Asegúrese de que el cable de suministro de energía esté protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato.

11. Use únicamente los dispositivos o accesorios especiﬁ cados por el fabricante.

12. Use únicamente la carretilla, plataforma, trípode, soporte o mesa especiﬁ cados por el fabricante o suministrados junto con el equipo.

Al transportar el equipo, tenga cuidado para evitar daños y caídas al tropezar con algún obstáculo.

13. Desenchufe el equipo durante tormentas o si no va a utilizarlo durante un periodo largo.

14. Confíe las reparaciones únicamente a servicios técnicos cualiﬁ cados. La unidad requiere mantenimiento siempre que haya sufrido algún daño, si el cable de suministro de energía o el enchufe presentaran daños, se hubiera derramado un líquido o hubieran caído objetos dentro del equipo, si el aparato hubiera estado expuesto a la humedad o la lluvia, si ha dejado de funcionar de manera normal o si ha sufrido algún golpe o caída.

15. Al conectar la unidad a la toma de corriente eléctrica asegúrese de que la conexión disponga de una unión a tierra.

16. Si el enchufe o conector de red sirve como único medio de desconexión, éste debe ser accesible fácilmente.

17. Cómo debe deshacerse de este aparato: Este símbolo indica que este aparato no debe ser tratado como basura orgánica, según lo indicado en la Directiva

WEEE (2012/19/EU) y a las normativas aplicables en su país. En lugar de ello deberá llevarlo al punto limpio más cercano para el reciclaje de sus elementos eléctricos / electrónicos (EEE). Al hacer esto estará ayudando a prevenir las posibles consecuencias negativas para el medio ambiente y la salud que podrían ser provocadas por una gestión inadecuada de este tipo de aparatos. Además, el reciclaje de materiales ayudará a conservar los recursos naturales. Para más información acerca del reciclaje de este aparato, póngase en contacto con el Ayuntamiento de su ciudad o con el punto limpio local.

NEGACIÓN LEGAL

MUSIC Group no admite ningún tipo de responsabilidad por cualquier daño o pérdida que pudiera sufrir cualquier persona por conﬁ ar total o parcialmente en la descripciones, fotografías o aﬁ rmaciones contenidas en este documento. Las especiﬁ caciones técnicas, imágenes y otras informaciones contenidas en este documento están sujetas a modiﬁ caciones sin previo aviso. Todas las marcas comerciales que aparecen aquí son propiedad de sus respectivos dueños. MIDAS, KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA y TC APPLIED TECHNOLOGIES son marcas comerciales o marcas registradas de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Reservados todos los derechos.

GARANTÍA LIMITADA

Si quiere conocer los detalles y condiciones aplicables de la garantía así como información adicional sobre la Garantía limitada de MUSIC Group, consulte online toda la información en la web music-group.com/warranty.

Page 3

TCX series Quick Start Guide

Consignes de sécurité

Les points repérés par ce symbole portent une tension

électrique sufﬁ sante pour constituer un risque d’électrocution. Utilisez uniquement des câbles d’enceintes de haute qualité disponibles dans les points de vente avec les connecteurs Jack mono 6,35 mm déjà installés. Toute autre installation ou modiﬁ cation doit être effectuée uniquement par un personnel qualiﬁ é.

Ce symbole avertit de la

présence d’une tension

dangereuse et non isolée à l’intérieur de l’appareil - elle peut provoquer des chocs électriques.

Attention

Ce symbol signale les

consignes d’utilisation et d’entre ! Tien importantes dans la documentation fournie. Lisez les consignes de sécurité du manuel d’utilisation de l’appareil.

Attention

Pour éviter tout risque de

choc électrique, ne pas ouvrir le capot de l’appareil ni démonter le panneau arrière. L’intérieur de l’appareil ne possède aucun élément réparable par l’utilisateur. Laisser toute réparation à un professionnel qualiﬁ é.

Attention

Pour réduire les risques de feu

et de choc électrique, n’exposez pas cet appareil à la pluie, à la moisissure, aux gouttes ou aux éclaboussures. Ne posez pas de récipient contenant un liquide sur l’appareil (un vase par exemple).

Attention

Ces consignes de sécurité et

d’entretien sont destinées à un personnel qualiﬁ é. Pour éviter tout risque de choc électrique, n’effectuez aucune réparation sur l’appareil qui ne soit décrite par le manuel d’utilisation. Les éventuelles réparations doivent être effectuées uniquement par un technicien spécialisé.

1. Lisez ces consignes.

2. Conservez ces consignes.

3. Respectez tous les avertissements.

4. Respectez toutes les consignes

d’utilisation.

5. N’utilisez jamais l’appareil à proximité d’un liquide.

6. Nettoyez l’appareil avec un chiffon sec.

7. Veillez à ne pas empêcher la bonne

ventilation de l’appareil via ses ouïes de ventilation. Respectez les consignes du fabricant concernant l’installation de l’appareil.

8. Ne placez pas l’appareil à proximité d’une source de chaleur telle qu’un chauffage, une cuisinière ou tout appareil dégageant de la chaleur (y compris un ampli de puissance).

9. Ne supprimez jamais la sécurité des prises bipolaires ou des prises terre. Les prises bipolaires possèdent deux contacts de largeur différente. Le plus large est le contact de sécurité. Les prises terre possèdent deux contacts plus une mise à la terre servant de sécurité. Si la prise du bloc d’alimentation ou du cordon d’ali-mentation fourni ne correspond pas à celles de votre installation électrique, faites appel à un électricien pour effectuer le changement de prise.

10. Installez le cordon d’alimentation de telle façon que personne ne puisse marcher dessus et qu’il soit protégé d’arêtes coupantes. Assurez-vous que le cordon d’alimentation est sufﬁsamment protégé, notamment au niveau de sa prise électrique et de l’endroit où il est relié à l’appareil; cela est également valable pour une éventuelle rallonge électrique.

11. Utilisez exclusivement des accessoires et des appareils supplémentaires recommandés par le fabricant.

12. Utilisez exclusivement des chariots, des diables, des présentoirs, des pieds et des surfaces de travail recommandés

par le fabricant ou livrés avec le produit. Déplacez précautionneusement tout chariot ou diable chargé pour éviter d’éventuelles blessures en cas de chute.

13. Débranchez l’appareil de la tension secteur en cas d’orage ou si l’appareil reste inutilisé pendant une longue période de temps.

14. Les travaux d’entretien de l’appareil doivent être effectués uniquement par du personnel qualiﬁé. Aucun entretien n’est nécessaire sauf si l’appareil est endommagé de quelque façon que ce soit (dommages sur le cordon d’alimentation ou la prise par exemple), si un liquide ou un objet a pénétré à l’intérieur du châssis, si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas correctement ou à la suite d’une chute.

15. L’appareil doit être connecté à une prise secteur dotée d’une protection par mise à la terre.

16. La prise électrique ou la prise IEC de tout appareil dénué de bouton marche/arrêt doit rester accessible en permanence.

17. Mise au rebut appropriée de ce produit: Ce symbole indique qu’en accord avec la directive DEEE (2012/19/EU) et les lois en vigueur dans votre pays, ce produit ne doit

pas être jeté avec les déchets ménagers. Ce produit doit être déposé dans un point de collecte agréé pour le recyclage des déchets d’équipements électriques et électroniques (EEE). Une mauvaise manipulation de ce type de déchets pourrait avoir un impact négatif sur l’environnement et la santé à cause des substances potentiellement dangereuses généralement associées à ces équipements. En même temps, votre coopération dans la mise au rebut de ce produit contribuera à l’utilisation efﬁ cace des ressources naturelles. Pour plus d’informations sur l’endroit où vous pouvez déposer vos déchets d’équipements pour le recyclage, veuillez contacter votre mairie ou votre centre local de collecte des déchets.

DÉNI LÉGAL

MUSIC Group ne peut être tenu pour responsable pour toute perte pouvant être subie par toute personne se ﬁ ant en partie ou en totalité à toute description, photographie ou afﬁ rmation contenue dans ce document. Les caractéristiques, l’apparence et d’autres informations peuvent faire l’objet de modiﬁ cations sans notiﬁ cation. Toutes les marques appartiennent à leurs propriétaires respectifs. MIDAS, KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA et TC APPLIED TECHNOLOGIES sont des marques ou marques déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Tous droits réservés.

GARANTIE LIMITÉE

Pour connaître les termes et conditions de garantie applicables, ainsi que les informations supplémentaires et détaillées sur la Garantie Limitée de MUSIC Group, consultez le site Internet music-group.com/warranty.

Wichtige Sicherheitshinweise

Vorsicht

Die mit dem Symbol

markierten Anschlü sse fü hren so viel Spannung, dass die Gefahr eines Stromschlags besteht. Verwenden Sie nur hochwertige, im Handel erhältliche Lautsprecherkabel mit vorinstallierten 6,3 mm TSSteckern. Alle anderen Installationen oder Modiﬁ kationen sollten nur von qualiﬁ ziertem Fachpersonal ausgefü hrt werden.

Achtung

Um eine Gefährdung durch

Stromschlag auszuschließen, darf die Geräteabdeckung bzw. Geräterückwand nicht abgenommen werden. Im Innern des Geräts beﬁ nden sich keine vom Benutzer reparierbaren Teile. Reparaturarbeiten dürfen nur von qualiﬁ ziertem Personal ausgeführt werden.

Achtung

Um eine Gefährdung durch

Feuer bzw. Stromschlag auszuschließen, darf dieses Gerät weder Regen oder Feuchtigkeit ausgesetzt werden noch sollten Spritzwasser oder tropfende Flüssigkeiten in das Gerät gelangen können. Stellen Sie keine mit Flüssigkeit gefüllten Gegenstände, wie z. B. Vasen, auf das Gerät.

Achtung

Die Service-Hinweise sind nur

durch qualiﬁ ziertes Personal zu befolgen. Um eine Gefährdung durch Stromschlag zu vermeiden, führen Sie bitte keinerlei Reparaturen an dem Gerät durch, die nicht in der Bedienungsanleitung beschrieben sind. Reparaturen sind nur von qualiﬁ ziertem Fachpersonal durchzuführen.

1. Lesen Sie diese Hinweise.

2. Bewahren Sie diese Hinweise auf.

3. Beachten Sie alle Warnhinweise.

4. Befolgen Sie alle Bedienungshinweise.

5. Betreiben Sie das Gerät nicht in der

Nähe von Wasser.

6. Reinigen Sie das Gerät mit einem trockenen Tuch.

7. Blockieren Sie nicht die Belüftungsschlitze. Beachten Sie beim Einbau des Gerätes die Herstellerhinweise.

8. Stellen Sie das Gerät nicht in der Nähe von Wärmequellen auf. Solche Wärmequellen sind z. B. Heizkörper, Herde oder andere Wärme erzeugende Geräte (auch Verstärker).

9. Entfernen Sie in keinem Fall die Sicherheitsvorrichtung von Zweipol- oder geerdeten Steckern. Ein Zweipolstecker hat zwei unterschiedlich breite Steckkontakte. Ein geerdeter Stecker hat zwei Steckkontakte und einen dritten Erdungskontakt. Der breitere Steckkontakt oder der zusätzliche Erdungskontakt dient Ihrer Sicherheit. Falls das mitgelieferte Steckerformat nicht zu Ihrer Steckdose passt, wenden Sie sich bitte an einen Elektriker, damit die Steckdose entsprechend ausgetauscht wird.

10. Verlegen Sie das Netzkabel so, dass es vor Tritten und scharfen Kanten geschützt ist und nicht beschädigt werden kann. Achten Sie bitte insbesondere im Bereich der Stecker, Verlängerungskabel und an der Stelle, an der das Netzkabel das Gerät verlässt, auf ausreichenden Schutz.

11. Das Gerät muss jederzeit mit intaktem Schutzleiter an das Stromnetz angeschlossen sein.

12. Sollte der Hauptnetzstecker oder eine Gerätesteckdose die Funktionseinheit zum Abschalten sein, muss diese immer zugänglich sein.

13. Verwenden Sie nur Zusatzgeräte/ Zubehörteile, die laut Hersteller geeignet sind.

14. Verwenden Sie nur Wagen, Standvorrichtungen, Stative, Halter oder Tische, die vom Hersteller benannt oder im Lieferumfang des

Geräts enthalten sind. Falls Sie einen Wagen benutzen, seien Sie vorsichtig beim Bewegen der Wagen- Gerätkombination, um Verletzungen durch Stolpern zu vermeiden.

15. Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gerät längere Zeit nicht benutzen.

16. Lassen Sie alle Wartungsarbeiten nur von qualiﬁ ziertem Service-Personal ausführen. Eine Wartung ist notwendig, wenn das Gerät in irgendeiner Weise beschädigt wurde (z. B. Beschädigung des Netzkabels oder Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, das Gerät nicht ordnungsgemäß funktioniert oder auf den Boden gefallen ist.

17. Korrekte Entsorgung dieses Produkts: Dieses Symbol weist darauf hin, das Produkt entsprechend der WEEE Direktive (2012/19/EU) und der jeweiligen nationalen

Gesetze nicht zusammen mit Ihren Haushaltsabfällen zu entsorgen. Dieses Produkt sollte bei einer autorisierten Sammelstelle für Recycling elektrischer und elektronischer Geräte (EEE) abgegeben werden. Wegen bedenklicher Substanzen,

die generell mit elektrischen und elektronischen Geräten in Verbindung stehen, könnte eine unsachgemäße Behandlung dieser Abfallart eine negative Auswirkung auf Umwelt und Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag zur richtigen Entsorgung dieses Produkts die effektive Nutzung natürlicher Ressourcen. Für weitere Informationen zur Entsorgung Ihrer Geräte bei einer Recycling-Stelle nehmen Sie bitte Kontakt zum zuständigen städtischen Büro, Entsorgungsamt oder zu Ihrem Haushaltsabfallentsorger auf.

HAFTUNGSAUSSCHLUSS

MUSIC Group übernimmt keine Haftung für Verluste, die Personen entstanden sind, die sich ganz oder teilweise auf hier enthaltene Beschreibungen, Fotos oder Aussagen verlassen haben. Technische Daten, Erscheinungsbild und andere Informationen können ohne vorherige Ankündigung geändert werden. Alle Warenzeichen sind Eigentum der jeweiligen Inhaber. MIDAS, KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA und TC APPLIED TECHNOLOGIES sind Warenzeichen oder eingetragene Warenzeichen der MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Alle Rechte vorbehalten.

BESCHRÄNKTE GARANTIE

Die geltenden Garantiebedingungen und zusätzliche Informationen bezüglich der von MUSIC Group gewährten beschränkten Garantie ﬁ nden Sie online unter music-group.com/warranty.

Page 4

TCX series Quick Start Guide

Instruções de Segurança Importantes

Aviso!

Terminais marcados com o

símbolo carregam corrente elétrica de magnitude suﬁ ciente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes comercialmente disponíveis de alta qualidade com plugues TS de ¼" pré-instalados. Todas as outras instalações e modiﬁ cações devem ser efetuadas por pessoas qualiﬁ cadas.

Este símbolo, onde quer que o

encontre, alerta-o para a leitura

das instruções de manuseamento que acompanham o equipamento. Por favor leia o manual de instruções.

Atenção

De forma a diminuir o

risco de choque eléctrico, não remover a cobertura (ou a secção de trás). Não existem peças substituíveis por parte do utilizador no seu interior. Para esse efeito recorrer a um técnico qualiﬁ cado.

Atenção

Para reduzir o risco de

incêndios ou choques eléctricos o aparelho não deve ser exposto à chuva nem à humidade. Além disso, não deve ser sujeito a salpicos, nem devem ser colocados em cima do aparelho objectos contendo líquidos, tais como jarras.

Atenção

Estas instruções de operação

devem ser utilizadas, em exclusivo, por técnicos de assistência qualiﬁ cados. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação, salvo se possuir as qualiﬁ -cações necessárias. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação. Só o deverá fazer se possuir as qualiﬁ cações necessárias.

1. Leia estas instruções.

2. Guarde estas instruções.

3. Preste atenção a todos os avisos.

4. Siga todas as instruções.

5. Não utilize este dispositivo perto

de água.

6. Limpe apenas com um pano seco.

7. Não obstrua as entradas de ventilação.

Instale de acordo com as instruções do fabricante.

8. Não instale perto de quaisquer fontes de calor tais como radiadores, bocas de ar quente, fogões de sala ou outros aparelhos (incluindo ampliﬁ cadores) que produzam calor.

9. Não anule o objectivo de segurança das ﬁ chas polarizadas ou do tipo de ligação à terra. Uma ﬁ cha polarizada dispõe de duas palhetas sendo uma mais larga do que a outra. Uma ﬁ cha do tipo ligação à terra dispõe de duas palhetas e um terceiro dente de ligação à terra. A palheta larga ou o terceiro dente são fornecidos para sua segurança. Se a ﬁ cha fornecida não encaixar na sua tomada, consulte um electricista para a substituição da tomada obsoleta.

10. Proteja o cabo de alimentação de pisadelas ou apertos, especialmente nas ﬁ chas, extensões, e no local de saída da unidade. Certiﬁ que-se de que o cabo eléctrico está protegido. Veriﬁ que particularmente nas ﬁ chas, nos receptáculos e no ponto em que o cabo sai do aparelho.

11. O aparelho tem de estar sempre conectado à rede eléctrica com o condutor de protecção intacto.

12. Se utilizar uma ﬁ cha de rede principal ou uma tomada de aparelhos para desligar a unidade de funcionamento, esta deve estar sempre acessível.

13. Utilize apenas ligações/acessórios especiﬁ cados pelo fabricante.

14. Utilize apenas com o carrinho, estrutura, tripé, suporte, ou mesa especiﬁ cados pelo fabricante ou vendidos com o dispositivo.

Quando utilizar um carrinho, tenha cuidado ao mover o conjunto carrinho/dispositivo para evitar danos provocados pela terpidação.

15. Desligue este dispositivo durante as trovoadas ou quando não for utilizado durante longos períodos de tempo.

16. Qualquer tipo de reparação deve ser sempre efectuado por pessoal qualiﬁ cado. É necessária uma reparação sempre que a unidade tiver sido de alguma forma daniﬁ cada, como por exemplo: no caso do cabo de alimentação ou ﬁ cha se encontrarem daniﬁ cados; na eventualidade de líquido ter sido derramado ou objectos terem caído para dentro do dispositivo; no caso da unidade ter estado exposta à chuva ou à humidade; se esta não funcionar normalmente, ou se tiver caído.

17. Correcta eliminação deste produto: este símbolo indica que o produto não deve ser eliminado juntamente com os resíduos domésticos, segundo a Directiva REEE

(2012/19/EU) e a legislação nacional. Este produto deverá ser levado para um centro de recolha licenciado para a reciclagem de resíduos de equipamentos eléctricos e electrónicos (EEE). O tratamento incorrecto deste tipo de resíduos pode ter um eventual impacto negativo no ambiente e na saúde humana devido a substâncias potencialmente perigosas que estão geralmente associadas aos EEE. Ao mesmo tempo, a sua colaboração para a eliminação correcta deste produto irá contribuir para a utilização eﬁ ciente dos recursos naturais. Para mais informação acerca dos locais onde poderá deixar o seu equipamento usado para reciclagem, é favor contactar os serviços municipais locais, a entidade de gestão de resíduos ou os serviços de recolha de resíduos domésticos.

LEGAL RENUNCIANTE

O MUSIC Group não se responsabiliza por perda alguma que possa ser sofrida por qualquer pessoa que dependa, seja de maneira completa ou parcial, de qualquer descrição, fotograﬁ a, ou declaração aqui contidas. Dados técnicos, aparências e outras informações estão sujeitas a modiﬁ cações sem aviso prévio. Todas as marcas são propriedade de seus respectivos donos. MIDAS, KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA e TC APPLIED TECHNOLOGIES são marcas ou marcas registradas do MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Todos direitos reservados.

GARANTIA LIMITADA

Para obter os termos de garantia aplicáveis e condições e informações adicionais a respeito da garantia limitada do MUSIC Group, favor veriﬁ car detalhes na íntegra através do website music-group.com/warranty.

安全にお使いいただくために

注意

感電の.恐れがありますので、 カバーやその他の部品を取り

外したり、開けたりしないでください。高品質なプロ用スピーカーケーブル（¼" TS 標準ケーブルおよびツイストロッキング プラグケーブル）を使用してください。

注意

火事および感電の危険を防ぐ

ため、本装置を水分や湿気のあるところには設置しないで下さい。装置には決して水分がかからないように注意し、花瓶など水分を含んだものは、装置の上には置かないようにしてください。

注意

このマークが表示されている

箇所には、内部に高圧電流が生じています。手を触れると感電の恐れがあります。

注意

取り扱いとお手入れの方法に

ついての重要な説明が付属の取扱説明書に記載されています。ご使用の前に良くお読みください。

注意

1. 取扱説明書を通してご覧ください。

2. 取扱説明書を大切に保管してくだ

さい。

3. 警告に従ってください。

4. 指示に従ってください。

5. 本機を水の近くで使用しないでくだ

さい。

6. お手入れの際は常に乾燥した布巾を使ってください。

7. 本機は、取扱説明書の指示に従い、適切な換気を妨げない場所に設置してください。取扱説明書に従って設置してください。

8. 本機は、電気ヒーターや温風機器、ストーブ、調理台やアンプといった熱源から離して設置してください。

9. ニ極式プラグおよびアースタイプ (三芯)プラグの安全ピンは取り外さないでください。ニ極式プラグにはピンが二本ついており、そのうち一本はもう一方よりも幅が広くなっています。アースタイプの三芯プラグにはニ本のピンに加えてアース用のピンが一本ついています。これらの幅の広いピン、およびアースピンは、安全のためのものです。備え付けのプラグが、お使いのコンセントの形状と異なる場合は、電器技師に相談してコンセントの交換をして下さい。

10. 電源コードを踏みつけたり、挟んだりしないようご注意ください。電源コードやプラグ、コンセント及び製品との接続には十分にご注意ください。

11. すべての装置の接地(アース)が確保されていることを確認して下さい。

12. 電源タップや電源プラグは電源遮断機として利用されている場合には、これが直ぐに操作できるよう手元に設置して下さい。

13. 付属品は本機

製造元が指定したもののみをお使いください。

14. カートスタンド、三脚、ブラケット、テーブルなどは、本機製造元が指定したもの、もしくは本機の付属品となるもののみをお使いください。カートを使用しての運搬の際は、器具の落下による怪我に十分ご注意ください。

15. 雷雨の場合、もしくは長期間ご使用にならない場合は、電源プラグをコンセントから抜いてください。

16. 故障の際は当社指定のサービス技術者にお問い合わせください。電源コードもしくはプラグの損傷、液体の装置内への浸入、装置の上に物が落下した場合、雨や湿気に装置が晒されてしまった場合、正常に作動しない場合、もしくは装置を地面に落下させてしまった場合など、いかなる形であれ装置に損傷が加わった場合は、装置の修理・点検を受けてください。

17. 本製品に電源コードが付属されている場合、付属の電源コードは本製品以外ではご使用いただけません。電源コードは必ず本製品に付属された電源コードのみご使用ください。

法的放棄

ここに含まれる記述、写真、意見の全体または一部に依拠して、いかなる人が損害を生じさせた場合にも、MUSIC Group は一切の賠償責任を負いません。技術仕様、外観およびその他の情報は予告なく変更になる場合があります。商標はすべて、それぞれの所有者に帰属します。MIDAS、KLARK TEKNIK、

LAB.GRUPPEN、LAKE、TANNOY、 TURBOSOUND、TC ELECTRONIC、 TC-HELICON、BEHRINGER、 BUGERA、DDAおよび TC APPLIED TECHNOLOGIESは MUSIC Group IP Ltd.の商標または登録商標です。© MUSIC Group IP Ltd. 2015無断転用禁止。

限定保証

適用される保証条件とMUSIC Group の限定保証に関する概要については、 オンライン上music-group.com/warranty にて詳細をご確認ください。

Page 5

TCX series Quick Start Guide

Getting Started

Models covered by this Quick Start Guide

TCX82-R / TCX82-R-WH, TCX102-R / TCX102-R-WH, TCX122- R / TCX122- R-W H , TCX152- R / TCX152-R-WH,

TCX115B-R / TCX115B-R-WH, TCX118B-R / TCX118B-R-WH

Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further

information about this or any other product, please visit our website at turbosound.com.

System Requirements

TCX series two-way loudspeakers operate as passive systems and require only one ampliﬁ er channel for

correct operation; the internal passive crossover network built into each enclosure splits the frequency

range appropriately between the LF driver and the HF driver. TCX weather-resistant loudspeakers are

equipped with a 2 metre 2-core cable tail for connection to your chosen cabling infrastructure. To avoid

wasting ampliﬁ er power you should use heavy-duty speaker cable with a minimum wire size of 12 gauge

(1.5 mm2), and preferably 10 gauge (2.5 mm2) for longer runs. For extreme cable lengths be aware of

cable impedance and resistive losses. Always observe the correct polarity. Connect the brown wire to the

positive ampliﬁ er output (+ve) and the blue wire to the negative ampliﬁ er output (-ve).

Ampliﬁ er Considerations

TCX series loudspeaker enclosures should be driven by high quality power ampliﬁ ers designed for true

professional use. Power ampliﬁ ers should be capable of delivering long term broadband power equal

to half the loudspeaker’s peak power rating at its stated nominal impedance. The use of under powered

ampliﬁ ers must be avoided as heavily clipped signals can cause permanent loudspeaker damage.

System Controllers

TCX systems can be used with TURBOSOUND LMS-D24 or LMS-D26 controllers to provide improved

performance as well as vital operating and system security features. If you do not have a controller,

please contact your TURBOSOUND dealer for further details. TURBOSOUND LMS-D2X controllers provide

preset slots into which you can load TCX loudspeaker model parameters, available as a free download.

To use your TCX loudspeaker with a TURBOSOUND controller:

1. Download and install the TCX loudspeaker presets from the TURBOSOUND website turbosound.com.

2. Power up the controller(s) and associated power ampliﬁ ers.

3. Press RECALL to select the appropriate program from the preset menu using the ‘A’ ROTARY ENCODER.

4. Press RECALL again to accept the preset. The controller will un-mute and is then ready for use.

᧙᜷ᄋ߸Мᮍᅽ

ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధ ܹᄋႄุߜڛᝐႄԁᬘǎᬎ Ώၺࣝధ ¼" TSᩛତ݁

ᄋᰵַ᠐˅ˋܧ٩ጴǎధᄋ߸ᜊួ ஠ڪᮍႁՍಬᄋ˅ˋցᤊᛢǎ

൦ಗ঄ଣᧉ১ַаߜڛఴ ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ

൦ಗ঄ଣᧉ১ಋ󰪀ᬅᄋ᧙᜷ ᄋΏၺԤ፦οឮ௛ǎឱ󰪀឵ధ Угǎ

࠶

˟ᥙГᝐႄԁᬘឱӉ఼

ᮈᄧᑁ᭨૖ౝǎ᝻ܭа෦ ధԼΚၺ፦οΏၺᄋᦋǎឱ࠳፦ο ᮋႁՍಬᄋ˅ˋցᤊᛢǎ

࠶

˟ᥙГᅍ༣ᝐႄԁᬘឱӉ

࠳൦᝻ܭᎷᭂ๹໾ິ˘ǎ ൦᝻ܭ˸ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ ٩˸ˁԼᎷЦʾݡᔊၬ኏ǎ

11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘ᦢǎ

12. ឱԷΏၺԉࠓ

૊ࠁᄋᬥ᠏ᩚ ׭ᄋଏᢽ౷ߖ ʽᝉ౷஄౷֘ಹ ߖǎᔫΏၺଏᢽ ౐ୄᤃ᝻ܭឱญ ߸М஋Ꮇ᝻ܭ ᥙГଏᢽ֘᝻

ܭϛωᏬԫǎ

13. ᥆󰩧ႄᭈᲟ󰩤ఱˁΏၺశ᝻ܭ௒ ឱફѤႄ຺ତ݁ǎ

14. ధ፦οڪᮍႁՍಬᄋ፦οցᤊ ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴ ႄ຺ତ݁ԫ૰๰͵ุЛྮᗁЛ᝻ܭ а᝻ܭᥔᭂ๹ԫ໾᝻ܭˁᑠ൥ࣣᤃͼ ᜃ୒گǎ

15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ εઑǎ

16. ᔫႄ຺ତ݁٩Ч ᏺՍ٩ၺͼளႄᜊᎷ ε᝾߳ܬᬥ௒Լ ஶΨ୳ͼ࿅ঘǎ

17. శַᤡၺ๓ફ 2000ዜʿڢӞశַ ᤡၺ᭥མࣝජό౏ ʿǎ

ฃܧ௛

ࠬͶڃڛ൦ឮ௛˻ଣ҃ᄋМᦋ ᦋଢᤙǍڐྠܧ௛Ꮼᤶᄋ૰݀ MUSIC Groupˁ᠈Ͷ᠋ǎ઀సԡஞ ֘ܲ᜻ᔫధటஉিˁԴᛢᤱᅽǎధᄋ ׹ಗڪ˟ЦՋᒮధᏩᄋ᠊ǎMIDAS,

KLARK TEKNIK, LAB.GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC-HELICON, BEHRINGER, BUGERA, DDA ֘TC APPLIED TECHNOLOGIES௨ MUSIC Group IP Ltd.ОՄᄋ׹ಗ ญг׹ಗǎ© MUSIC Group IP Ltd. 2015ྡీధǎ

εο౏൝

ధУᮄˮᬸڅεοᄋᤡၺ౏ ൝ԤЦ߳ᄲУθ্ឱᄇᬇ music-group.com/warranty Ꭻቤಋᄻߺ஠ᄋឡጻθ্ǎ

࠶

፦οឮ௛௨ፍՍಬᄋ˅ˋ፦

οցΏၺ ᄋǎ˟ᥙГᝐႄԁ ᬘᬕΏၺឮ௛˻ଣ҃ᄋܲឱӉᤊᛢ ͶЦ߳፦οǎధ፦οڪᮍႁՍಬᄋ˅ ˋցᤊᛢǎ

1. ឱ󰪀឵ᤉឮ௛ǎ

2. ឱݱؔεߜᤉឮ௛ǎ

3. ឱญధᄋ᝞ᇩǎ

4. ឱᥗ߷ధᄋឮ௛ǎ

5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַǎ

6. ឱၺࣱ࣌ຎพశַǎ

7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ௒ឱᥗ

ཱིԉࠓᄋឮ௛ǎ

8. ឱӉ࠳శַ߸ᜊڛམ຺ᬅᤄ ݡ఍ජྠ༰ߖЦ߳ၸམ᧛ᄋ᝻ܭ Ӌ઻ҫ஋٩ǎ

9. ឱӉሩᬕ౞মତ݁଍ڢତ݁ᄋ߸М ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕ ଍ڢ݁౟ǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১ ᄋତឱႄࢻట૲ʸ˕Սᤡᄋତǎ

10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇ҉ ᆢࡀЦญႄ຺ତ݁Ǎܴၺ᤮ତԤ᝻ܭ ᤍ଍ܬǎ

Page 6

TCX series Quick Start Guide

Networking Capability with LMS series Controllers

• • LMS-D2X controllers are designed to offer control and monitoring of system parameters over a BvNet

network in real time using a PC and TurboDrive software. The controllers are equipped with network

cards to allow the building of comprehensive networked loudspeaker systems.

• • Download the TurboDrive software from the supplied CD or from the TURBOSOUND website

turbosound.com and follow the installation instructions.

• • Install the drivers. If connecting via RS232 there is no need to install drivers. If connecting via USB

install the USB drivers that can be found on the CD that came with your Linea Research USB interface.

• • Networking multiple devices to a PC: BvNet is the method of connecting multiple devices and this is

done with the Linea Research USB & RS232 Interface (available from TURBOSOUND). The interface

enables devices to be connected to a PC either using RS232 or using USB. EIA485 is the network

protocol among the networked devices and is carried over CAT5-type cables. It works with the

following: PC with Windows NT, Windows 2000, Windows XP, or Windows Vista operating systems,

or with Pentium processor, or CD ROM drive or internet access, RS232 or USB port.*

• • RS232: Connect your computer to the BvNet interface using a standard 9-pin serial cable. External power is

required for RS232 operation and this should be provided by the Linea Research Accessory Power Supply.

• • USB: Connect your computer to the BvNet interface using a USB Type A to USB Type B cable.

External power is not required when using USB.

• • Connect networked devices via RJ45 CAT5 cables.

• • Launch the TurboDrive software.

• • Application Authorisation: TurboDrive prompts for an Authorisation Code on the ﬁ rst launch

which is PJLUWZ.

• • Select the COM port from Network > Com Port.

• • Click the Online toolbar button.

• • Click on one of the devices that appear in the tree view to Launch the panel.

• • When the progress bar indicates ready, adjust the controls as required.

• • Please refer to the TurboDrive User Guide for further information on networking.

Outdoor Applications

TCX weather-resistant products are designed to provide robust protection against the elements when

used outdoors in harsh environments. The cabinet is fully sealed inside and out, protected with a Weather

resistant paint ﬁ nish, and the plated and outdoor powder-coated perforated steel grille backed with

reticulated foam resists the impact of showers. Hard wired speaker connection is made via a 2-core cable

tail ﬁ tted through a weather-sealed cable gland mounted on an aluminium connector plate. Stainless steel

external ﬁ xings are used throughout. Internally, the drivers are treated to resist moisture absorption while

the internal corner brackets are zinc plated and outdoor powder-coated.

While TCX series loudspeakers with the “R” sufﬁ x are constructed for outdoor use, care should be taken

when installing these loudspeakers outdoors in coastal areas where high salinity and extreme temperature

variations are present in addition to high humidity and UV light exposure.

Loudspeakers must always be mounted with a downward angle. Do not allow loudspeakers to become

fully immersed in water at any time. Routine inspection and maintenance programs must be carried out on

a regular basis and parts replaced as necessary to provide continued satisfactory performance.

Mounting and Fixing

TCX series cabinets are designed with multiple internal rigging points to suit many possible mounting

methods in permanent installations. The table below summarises the mounting accessories available for

each model.

Model Wall mount Ceiling mount Eyebolts

TCX82-R WB-20 CB-20 EB-10-40

TCX102-R WB-20 CB-20 EB-10-40

TCX122-R WB-20 CB-20 EB-10-40

TCX152-R WB-20 CB-20 EB-10-40

TCX115B-R N/A N/A EB-10-40

TCX118B-R N/A N/A EB-10-40

Wall Brackets

1. Separate the component parts of the bracket into the wall plate and

speaker plate assemblies by removing the nylock nut underneath the

wall plate horizontal lug.

2. Remove the countersunk bolts on the rear panel of the cabinet and

attach the speaker plate to the cabinet with the bolts supplied.

3. Fix the wall plate in the venue using appropriate ﬁ xings

(not supplied), ensuring that the cable access hole is towards the top.

4. Lift the loudspeaker on to the wall plate and locate the large

captive bolt welded to the speaker plate through the wall plate lug.

Re-assemble the bracket parts, adjust the aim of the loudspeaker and

tighten all bolts.

Ceiling Brackets

1. Separate the component parts of the bracket into the ceiling plate and

speaker plate assemblies by removing the nylock nut underneath the

wall plate lug.

2. Remove the countersunk bolts on the rear panel of the cabinet and

attach the speaker plate to the cabinet with the bolts supplied.

3. Fix the ceiling plate in the venue using appropriate ﬁ xings

(not vvvvsupplied). Lift the loudspeaker on to the ceiling plate and

re-assemble the bracket ﬁ xings, adjust the aim of the loudspeaker and

tighten all bolts.

Illustr ated: TCX152 on a WB-55 wall bracke t

Illustr ated: TCX122 on a CB-55 wall bracke t

*Windows NT, Windows 2000, Windows XP and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a trademark of Intel Corporation in the U.S. and/or other countries.

Page 7

TCX series Quick Start Guide

OmniMount Brackets

The internal rigging points are also compatible with OmniMount wall and ceiling brackets. To mount TCX

cabinets with OmniMount brackets follow the instructions provided with the brackets.

Suspending with Eyebolts

TCX cabinets can be suspended using optional eyebolts coupled to the internal

rigging points provided on the top, bottom and sides and back. The simplest

method is to use the two rigging points on the top and a single pull-back rigging

point in the centre of the rear panel.

Remove the appropriate countersunk screws and replace them with shoulder

eyebolts, which must have a thread length of at least 18 mm. Use the rear

rigging point to angle the cabinet for optimum room coverage. Cabinets may be

hung upside down if required.

IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless

undertaken by qualiﬁ ed personnel with the required experience and certiﬁ cation to perform the necessary

tasks. Walls, ﬂ oors or ceilings must be capable of safely and securely supporting the actual load.

The mounting accessory used must be safely and securely ﬁ xed both to the loudspeaker and to the wall,

ﬂ oor or ceiling.

When mounting rigging components on walls, ﬂ oors or ceilings, ensure that all ﬁ xings and fasteners

used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and

composition of walls and ceilings, all need to be taken into account when determining whether a

particular ﬁ xing arrangement can be safely employed for a particular load. Cavity plugs or other specialist

ﬁ xings, if required, must be of an appropriate type, and must be ﬁ tted and used in accordance with the

maker’s instructions.

The operation of your speaker cabinet as part of a ﬂ own system, if installed incorrectly and improperly,

can potentially expose persons to serious health risks and even death. In addition, please ensure that

electrical, mechanical and acoustic considerations are discussed with qualiﬁ ed and certiﬁ ed (by local state

or national authorities) personnel prior to any installation or ﬂ ying.

Make sure that speaker cabinets are set up and ﬂ own by qualiﬁ ed and certiﬁ ed personnel only,

using dedicated equipment and original parts and components delivered with the unit. If any parts or

components are missing please contact your Dealer before attempting to set up the system.

Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group,

including the MUSIC Group companies listed on the enclosed “Service Information Sheet”, assumes no

liability for any damage or personal injury resulting from improper use, installation or operation of the

product. Regular checks must be conducted by qualiﬁ ed personnel to ensure that the system remains in a

secure and stable condition. Make sure that, where the speaker is ﬂ own, the area underneath the speaker is

free of human trafﬁ c. Do not ﬂ y the speaker in areas that can be entered or used by members of the public.

Speakers create a magnetic ﬁ eld, even if not in operation. Therefore, please keep all materials that can

be affected by such ﬁ elds (discs, computers, monitors, etc) at a safe distance. A safe distance is usually

between 1 and 2 metres.

Servicing and Driver Removal

1. Place the cabinet on its back on a suitable work surface. Remove the eight Pozidrive countersunk screws

that hold the grille in place and set the grille aside (ﬁ g 1).

2. Remove the M5 hex head bass driver ﬁ xings screws (ﬁ g 2).

3. Disconnect and remove the bass driver, making a note of the polarity for later reconnection (ﬁ g 3).

4. Remove the M5 hex head HF horn ﬁ xing screws (ﬁ g 4).

 g 1  g 2  g 3

5. Lift out the horn and compression driver assembly. Disconnect the cables from the compression driver,

making a note of the polarity for later reconnection (ﬁ g 5).

6. Reinstatement is a simple reversal of the above process. Reconnect the compression driver cables,

observing the correct polarity (white cable to the +ve terminal, green cable to the –ve terminal).

7. Replace the horn and driver in the cabinet.

8. Replace the horn ﬁ xing screws and tighten.

 g 4  g 5

9. Reconnect the bass driver cables, observing the correct polarity (red cable to the +ve terminal, black cable

to the –ve terminal) and reinstate the driver in the cabinet. Replace and tighten the driver ﬁ xing screws.

10. Replace the grille and phase check the cabinet before use.

Page 8

TCX series Quick Start Guide

Rotating the HF Horn Pattern

The high frequency horn in all TCX two-way models can

be rotated through 90° in order to swap the horizontal

and vertical dispersion patterns, particularly useful to

retain the wide horizontal dispersion when the cabinet is

installed horizontally.

1. Remove the loudspeaker grille as before.

2. Remove the M5 hex head HF horn ﬁ xing screws.

3. Lift the horn / driver assembly out, rotate the horn as

necessary to achieve the desired coverage pattern and

replace it in the cabinet.

4. Replace the horn ﬁ xing screws and tighten.

5. Replace the grille and phase check the cabinet before use.

EASE Data

EASE data is available for TCX series loudspeakers to enable software simulation of audio coverage

installation projects. Please visit turbosound.com for a free EASE data download.

Technical Speciﬁ cations

TCX152 (WH)-R TCX118B (WH)-R TCX115B (WH)-R

System

Frequency response

85 Hz - 18 kHz ±3 dB 55 Hz - 20 kHz -10 dB

35 Hz - 125 Hz ±3 dB 25 Hz - 170 Hz -10 dB

35 Hz - 125 Hz ±3 dB 28 Hz - 170 Hz -10 dB

Nominal dispersion

90° H x 60° V @ -6 dB points Half space Half space

Power handling (IEC)

350 W continuous, 1400 W peak

1,000 W continuous, 4,000 W peak

1,000 W continuous, 4000 W peak

Sensitivity

99 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 95 dB (1 W @ 1 m)

Maximum SPL

125 dB continuous, 131 dB peak 127 dB continuous, 133 dB peak 125 dB continuous, 131 dB peak

Impedance

8 Ω 8 Ω 8 Ω

Components

1 x 15" (381 mm) LF driver 1 x 1" (25 mm) HF compression driver

1 x 18" (457 mm) LF driver 1 x 15" (380 mm) LF driver

Enclosure

Connectors

2-core captive cable tail 2-core captive cable tail 2-core captive cable tail

Wiring

Brown +VE input, Blue -VE input Brown +VE input, Blue -VE input Brown +VE input, Blue -VE input

Dimensions HWD

652 x 466 x 422 mm (25.6 x 18.3 x 16.7")

660 x 560 x 660 mm (26.0 x 22.0 x 26.0")

600 x 499 x 600 mm (23.6 x 19.7 x 23.6")

Net weight

23.5 kg (51.8 lbs) 42.1 kg (92.8 lbs) 36.7 kg (80.9 lbs)

Construction

15 mm (

/8") birch plywood 15 mm (5/8") birch plywood 15 mm (5/8") birch plywood

Finish

Semi matt black paint (white optional)

Grille

Powder coated perforated Zinc plated steel

Flying hardware

M10 x 9, M8 x 4, M6 x 4 Points M10 x 8 Points M10 x 8 Points

TCX122 (WH)-R TCX102 (WH)-R TCX82 (WH)-R

System

Frequency response

100 Hz - 18 kHz ±3 dB 68 Hz - 20 kHz -10 dB

100 Hz - 20 kHz ±3 dB 68 Hz - 20 kHz -10 dB

100 Hz - 20 kHz ±3 dB 70 Hz - 20 kHz -10 dB

Nominal dispersion

90° H x 60° V @ -6 dB points 90° H x 60° V @ -6 dB points 90° H x 60° V @ -6 dB points

Power handling (IEC)

300 W continuous, 1,200 W peak 250 W continuous, 1000 W peak 200 W continuous, 800 W peak

Sensitivity

97 dB (1 W @ 1 m) 95 dB (1 W @ 1 m) 94 dB (1 W @ 1 m)

Maximum SPL

122 dB continuous, 128 dB peak 119 dB continuous, 125 dB peak 117 dB continuous, 123 dB peak

Impedance

8 Ω 8 Ω 8 Ω

Components

1 x 12" (305 mm) LF driver 1 x 1" (25 mm) HF compression driver

1 x 10" (254 mm) LF driver 1 x 1" (25 mm) HF compression driver

1 x 8" (203 mm) LF driver 1 x 1" (25 mm) HF compression driver

Enclosure

Connectors

2-core captive cable tail 2-core captive cable tail 2-core captive cable tail

Wiring

Brown +VE input, Blue -VE input Brown +VE input, Blue -VE input Brown +VE input, Blue -VE input

Dimensions HWD

552 x 406 x 368 mm (21.8 x 15.9 x 14.5")

488 x 366 x 332 mm (19.2 x 14.4 x 13.0")

408 x 308 x 280 mm (16.0 x 12.1 x 11.0")

Net weight

18.3 kg (40.2 lbs) 15.1 kg (33.3 lbs) 10.3 kg (22.7 lbs)

Construction

15 mm (

/8") birch plywood 15 mm (5/8") birch plywood 12 mm (1/2") birch plywood

Finish

Semi matt black paint (white optional)

Grille

Powder coated perforated Zinc plated steel

Flying hardware

M10 x 9, M8 x 4, M6 x 4 Points M10 x 9, M8 x 4, M6 x 4 Points M10 x 9, M8 x 4, M6 x 4 Points

Page 9

TCX series Quick Start Guide

1. Register online. Please register your

new MUSIC Group equipment right after you purchase it by visiting turbosound. com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efﬁ ciently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your MUSIC Group Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fulﬁ ller for your country listed under “Support” at turbosound. com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at turbosound. com. Alternatively, please submit an online warranty claim at turbosound. com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

Important information

Other important information

Page 10