Turbosound TCS122/94-R, TCS122/96-R, TCS152/96-R, TCS122/64-R, TCS122/94-R-WH Quick Start Guide

...
TCS Weather Resistant Series
(
)
TCS62-R (R-WH), TCS122/64-R (R-WH), TCS122/96-R (R-WH), TCS122/94-R (R-WH), TCS152/64-R (R-WH), TCS152/96-R (R-WH), TCS152/94-R (R-WH), TCS115B-R (R-WH), TCS218B-R (R-WH)
Arrayable 2 Way Full Range Loudspeakers for Installation Applications
Arrayable 2 Way Full Range Loudspeakers for Installation Application (Weather Resistant)
Weather Resistant
2
TCS Passive R series Quick Start Guide
3
Important Safety Instructions
Terminals marked with this symbol carry electrical
current of suffi cient magnitude to constitute risk of electric shock. Use only high-quality commercially-available speaker cables with plugs pre-installed. All other installation or modifi cation should be performed only by qualifi ed personnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated dangerous voltage inside the enclosure ­voltage that may be suffi cient to constitute a risk of shock.
This symbol, wherever it
appears, alerts you to important
operating and maintenance instructions in the accompanying literature. Please read the manual.
Caution
To reduce the risk of electric
shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualifi ed personnel.
Caution
To reduce the risk of fi re or
electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.
Caution
These service instructions are
for use by qualifi ed service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualifi ed service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/accessories specifi ed by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU)
and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effi cient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city offi ce, or your household waste collection service.
LEGAL DISCLAIMER
MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifi cations, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding MUSIC Group’s Limited Warranty, please see complete details online at music-group.com/warranty.
Instrucciones de seguridad
Las terminales marcadas con este símbolo transportan
corriente eléctrica de magnitud sufi ciente como para constituir un riesgo de descarga eléctrica. Utilice solo cables de altavoz de alta calidad con clavijas TS de 6,3 mm pre-instaladas (puede adquirirlos en comercios especializados en audio). Cualquier otra instalación o modifi cación debe ser realizada únicamente por un técnico cualifi cado.
Este símbolo, siempre que
aparece, le advierte de la
presencia de voltaje peligroso sin aislar dentro de la caja; este voltaje puede ser sufi ciente para constituir un riesgo de descarga.
Este símbolo, siempre que
aparece, le advierte sobre
instrucciones operativas y de mantenimiento que aparecen en la documentación adjunta. Por favor, lea el manual.
Atención
Para reducir el riesgo de
descarga eléctrica, no quite la tapa (o la parte posterior). No hay piezas en el interior del equipo que puedan ser reparadas por el usuario. Si es necesario, póngase en contacto con personal cualifi cado.
Atención
Para reducir el riesgo de
incendio o descarga eléctrica, no exponga este aparato a la lluvia, humedad o alguna otra fuente que pueda salpicar o derramar algún líquido sobre el aparato. No coloque ningún tipo de recipiente para líquidos sobre el aparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo exclusivamente personal cualifi cado. Para evitar el riesgo de una descarga eléctrica, no realice reparaciones que no se encuentren descritas en el manual de operaciones. Las reparaciones deben ser realizadas exclusivamente por personal cualifi cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
las advertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un paño seco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo con las instrucciones del fabricante.
8. No instale este equipo cerca de fuentes de calor tales como radiadores, acumuladores de calor, estufas u otros aparatos (incluyendo amplifi cadores) que puedan producir calor.
9. No elimine o deshabilite nunca la conexión a tierra del aparato o del cable de alimentación de corriente. Un enchufe polarizado tiene dos polos, uno de los cuales tiene un contacto más ancho que el otro. Una clavija con puesta a tierra dispone de tres contactos: dos polos y la puesta a tierra. El contacto ancho y el tercer contacto, respectivamente, son los que garantizan una mayor seguridad. Si el enchufe suministrado con el equipo no concuerda con la toma de corriente, consulte con un electricista para cambiar la toma de corriente obsoleta.
10. Coloque el cable de suministro de energía de manera que no pueda ser pisado y que esté protegido de objetos afi lados. Asegúrese de que el cable de suministro de energía esté protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato.
11. Use únicamente los dispositivos o accesorios especifi cados por el fabricante.
12. Use únicamente la carretilla, plataforma, trípode, soporte o mesa especifi cados por el fabricante o suministrados junto con el equipo.
Al transportar el equipo, tenga cuidado para evitar daños y caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante tormentas o si no va a utilizarlo durante un periodo largo.
14. Confíe las reparaciones únicamente a servicios técnicos cualifi cados. La unidad requiere mantenimiento siempre que haya sufrido algún daño, si el cable de suministro de energía o el enchufe presentaran daños, se hubiera derramado un líquido o hubieran caído objetos dentro del equipo, si el aparato hubiera estado expuesto a la humedad o la lluvia, si ha dejado de funcionar de manera normal o si ha sufrido algún golpe o caída.
15. Al conectar la unidad a la toma de corriente eléctrica asegúrese de que la conexión disponga de una unión a tierra.
16. Si el enchufe o conector de red sirve como único medio de desconexión, éste debe ser accesible fácilmente.
17. Cómo debe deshacerse de este aparato: Este símbolo indica que este aparato no debe ser tratado como basura orgánica, según lo indicado en la Directiva
WEEE (2012/19/EU) y a las normativas aplicables en su país. En lugar de ello deberá llevarlo al punto limpio más cercano para el reciclaje de sus elementos eléctricos / electrónicos (EEE). Al hacer esto estará ayudando a prevenir las posibles consecuencias negativas para el medio ambiente y la salud que podrían ser provocadas por una gestión inadecuada de este tipo de aparatos. Además, el reciclaje de materiales ayudará a conservar los recursos naturales. Para más información acerca del reciclaje de este aparato, póngase en contacto con el Ayuntamiento de su ciudad o con el punto limpio local.
NEGACIÓN LEGAL
MUSIC Group no admite ningún tipo de responsabilidad por cualquier daño o pérdida que pudiera sufrir cualquier persona por confi ar total o parcialmente en la descripciones, fotografías o afi rmaciones contenidas en este documento. Las especifi caciones técnicas, imágenes y otras informaciones contenidas en este documento están sujetas a modifi caciones sin previo aviso. Todas las marcas comerciales que aparecen aquí son propiedad de sus respectivos dueños. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA y DDA son marcas comerciales o marcas registradas de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Reservados todos los derechos.
GARANTÍA LIMITADA
Si quiere conocer los detalles y condiciones aplicables de la garantía así como información adicional sobre la Garantía limitada de MUSIC group, consulte online toda la información en la web music-group.com/warranty.
4
TCS Passive R series Quick Start Guide
5
Consignes de sécurité
Les points repérés par ce symbole portent une tension
électrique suffi sante pour constituer un risque d’électrocution. Utilisez uniquement des câbles d’enceintes de haute qualité disponibles dans les points de vente avec les connecteurs Jack mono 6,35 mm déjà installés. Toute autre installation ou modifi cation doit être effectuée uniquement par un personnel qualifi é.
Ce symbole avertit de la
présence d’une tension
dangereuse et non isolée à l’intérieur de l’appareil - elle peut provoquer des chocs électriques.
Attention
Ce symbol signale les
consignes d’utilisation et d’entre ! Tien importantes dans la documentation fournie. Lisez les consignes de sécurité du manuel d’utilisation de l’appareil.
Attention
Pour éviter tout risque de
choc électrique, ne pas ouvrir le capot de l’appareil ni démonter le panneau arrière. L’intérieur de l’appareil ne possède aucun élément réparable par l’utilisateur. Laisser toute réparation à un professionnel qualifi é.
Attention
Pour réduire les risques de feu
et de choc électrique, n’exposez pas cet appareil à la pluie, à la moisissure, aux gouttes ou aux éclaboussures. Ne posez pas de récipient contenant un liquide sur l’appareil (un vase par exemple).
Attention
Ces consignes de sécurité et
d’entretien sont destinées à un personnel qualifi é. Pour éviter tout risque de choc électrique, n’effectuez aucune réparation sur l’appareil qui ne soit décrite par le manuel d’utilisation. Les éventuelles réparations doivent être effectuées uniquement par un technicien spécialisé.
1. Lisez ces consignes.
2. Conservez ces consignes.
3. Respectez tous les avertissements.
4. Respectez toutes les consignes
d’utilisation.
5. N’utilisez jamais l’appareil à proximité d’un liquide.
6. Nettoyez l’appareil avec un chiffon sec.
7. Veillez à ne pas empêcher la bonne
ventilation de l’appareil via ses ouïes de ventilation. Respectez les consignes du fabricant concernant l’installation de l’appareil.
8. Ne placez pas l’appareil à proximité d’une source de chaleur telle qu’un chauffage, une cuisinière ou tout appareil dégageant de la chaleur (y compris un ampli de puissance).
9. Ne supprimez jamais la sécurité des prises bipolaires ou des prises terre. Les prises bipolaires possèdent deux contacts de largeur différente. Le plus large est le contact de sécurité. Les prises terre possèdent deux contacts plus une mise à la terre servant de sécurité. Si la prise du bloc d’alimentation ou du cordon d’ali-mentation fourni ne correspond pas à celles de votre installation électrique, faites appel à un électricien pour effectuer le changement de prise.
10. Installez le cordon d’alimentation de telle façon que personne ne puisse marcher dessus et qu’il soit protégé d’arêtes coupantes. Assurez-vous que le cordon d’alimentation est suffisamment protégé, notamment au niveau de sa prise électrique et de l’endroit où il est relié à l’appareil; cela est également valable pour une éventuelle rallonge électrique.
11. Utilisez exclusivement des accessoires et des appareils supplémentaires recommandés par le fabricant.
12. Utilisez exclusivement des chariots, des diables, des présentoirs, des pieds et des surfaces de travail recommandés
par le fabricant ou livrés avec le produit. Déplacez précautionneusement tout chariot ou diable chargé pour éviter d’éventuelles blessures en cas de chute.
13. Débranchez l’appareil de la tension secteur en cas d’orage ou si l’appareil reste inutilisé pendant une longue période de temps.
14. Les travaux d’entretien de l’appareil doivent être effectués uniquement par du personnel qualifié. Aucun entretien n’est nécessaire sauf si l’appareil est endommagé de quelque façon que ce soit (dommages sur le cordon d’alimentation ou la prise par exemple), si un liquide ou un objet a pénétré à l’intérieur du châssis, si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas correctement ou à la suite d’une chute.
15. L’appareil doit être connecté à une prise secteur dotée d’une protection par mise à la terre.
16. La prise électrique ou la prise IEC de tout appareil dénué de bouton marche/arrêt doit rester accessible en permanence.
17. Mise au rebut appropriée de ce produit: Ce symbole indique qu’en accord avec la directive DEEE (2012/19/EU) et les lois en vigueur dans votre pays, ce produit ne doit
pas être jeté avec les déchets ménagers. Ce produit doit être déposé dans un point de collecte agréé pour le recyclage des déchets d’équipements électriques et électroniques (EEE). Une mauvaise manipulation de ce type de déchets pourrait avoir un impact négatif sur l’environnement et la santé à cause des substances potentiellement dangereuses généralement associées à ces équipements. En même temps, votre coopération dans la mise au rebut de ce produit contribuera à l’utilisation effi cace des ressources naturelles. Pour plus d’informations sur l’endroit où vous pouvez déposer vos déchets d’équipements pour le recyclage, veuillez contacter votre mairie ou votre centre local de collecte des déchets.
DÉNI LÉGAL
MUSIC Group ne peut être tenu pour responsable pour toute perte pouvant être subie par toute personne se fi ant en partie ou en totalité à toute description, photographie ou affi rmation contenue dans ce document. Les caractéristiques, l’apparence et d’autres informations peuvent faire l’objet de modifi cations sans notifi cation. Toutes les marques appartiennent à leurs propriétaires respectifs. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA et DDA sont des marques ou marques déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Tous droits réservés.
GARANTIE LIMITÉE
Pour connaître les termes et conditions de garantie applicables, ainsi que les informations supplémentaires et détaillées sur la Garantie Limitée de MUSIC Group, consultez le site Internet music-group.com/warranty.
Wichtige Sicherheitshinweise
Vorsicht
Die mit dem Symbol
markierten Anschlü sse fü hren so viel Spannung, dass die Gefahr eines Stromschlags besteht. Verwenden Sie nur hochwertige, im Handel erhältliche Lautsprecherkabel mit vorinstallierten 6,3 mm TSSteckern. Alle anderen Installationen oder Modifi kationen sollten nur von qualifi ziertem Fachpersonal ausgefü hrt werden.
Achtung
Um eine Gefährdung durch
Stromschlag auszuschließen, darf die Geräteabdeckung bzw. Geräterückwand nicht abgenommen werden. Im Innern des Geräts befi nden sich keine vom Benutzer reparierbaren Teile. Reparaturarbeiten dürfen nur von qualifi ziertem Personal ausgeführt werden.
Achtung
Um eine Gefährdung durch
Feuer bzw. Stromschlag auszuschließen, darf dieses Gerät weder Regen oder Feuchtigkeit ausgesetzt werden noch sollten Spritzwasser oder tropfende Flüssigkeiten in das Gerät gelangen können. Stellen Sie keine mit Flüssigkeit gefüllten Gegenstände, wie z. B. Vasen, auf das Gerät.
Achtung
Die Service-Hinweise sind nur
durch qualifi ziertes Personal zu befolgen. Um eine Gefährdung durch Stromschlag zu vermeiden, führen Sie bitte keinerlei Reparaturen an dem Gerät durch, die nicht in der Bedienungsanleitung beschrieben sind. Reparaturen sind nur von qualifi ziertem Fachpersonal durchzuführen.
1. Lesen Sie diese Hinweise.
2. Bewahren Sie diese Hinweise auf.
3. Beachten Sie alle Warnhinweise.
4. Befolgen Sie alle Bedienungshinweise.
5. Betreiben Sie das Gerät nicht in der
Nähe von Wasser.
6. Reinigen Sie das Gerät mit einem trockenen Tuch.
7. Blockieren Sie nicht die Belüftungsschlitze. Beachten Sie beim Einbau des Gerätes die Herstellerhinweise.
8. Stellen Sie das Gerät nicht in der Nähe von Wärmequellen auf. Solche Wärmequellen sind z. B. Heizkörper, Herde oder andere Wärme erzeugende Geräte (auch Verstärker).
9. Entfernen Sie in keinem Fall die Sicherheitsvorrichtung von Zweipol- oder geerdeten Steckern. Ein Zweipolstecker hat zwei unterschiedlich breite Steckkontakte. Ein geerdeter Stecker hat zwei Steckkontakte und einen dritten Erdungskontakt. Der breitere Steckkontakt oder der zusätzliche Erdungskontakt dient Ihrer Sicherheit. Falls das mitgelieferte Steckerformat nicht zu Ihrer Steckdose passt, wenden Sie sich bitte an einen Elektriker, damit die Steckdose entsprechend ausgetauscht wird.
10. Verlegen Sie das Netzkabel so, dass es vor Tritten und scharfen Kanten geschützt ist und nicht beschädigt werden kann. Achten Sie bitte insbesondere im Bereich der Stecker, Verlängerungskabel und an der Stelle, an der das Netzkabel das Gerät verlässt, auf ausreichenden Schutz.
11. Das Gerät muss jederzeit mit intaktem Schutzleiter an das Stromnetz angeschlossen sein.
12. Sollte der Hauptnetzstecker oder eine Gerätesteckdose die Funktionseinheit zum Abschalten sein, muss diese immer zugänglich sein.
13. Verwenden Sie nur Zusatzgeräte/ Zubehörteile, die laut Hersteller geeignet sind.
14. Verwenden Sie nur Wagen, Standvorrichtungen, Stative, Halter oder Tische, die vom Hersteller benannt oder im Lieferumfang des
Geräts enthalten sind. Falls Sie einen Wagen benutzen, seien Sie vorsichtig beim Bewegen der Wagen- Gerätkombination, um Verletzungen durch Stolpern zu vermeiden.
15. Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gerät längere Zeit nicht benutzen.
16. Lassen Sie alle Wartungsarbeiten nur von qualifi ziertem Service-Personal ausführen. Eine Wartung ist notwendig, wenn das Gerät in irgendeiner Weise beschädigt wurde (z. B. Beschädigung des Netzkabels oder Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, das Gerät nicht ordnungsgemäß funktioniert oder auf den Boden gefallen ist.
17. Korrekte Entsorgung dieses Produkts: Dieses Symbol weist darauf hin, das Produkt entsprechend der WEEE Direktive (2012/19/EU) und der jeweiligen nationalen
Gesetze nicht zusammen mit Ihren Haushaltsabfällen zu entsorgen. Dieses Produkt sollte bei einer autorisierten Sammelstelle für Recycling elektrischer und elektronischer Geräte (EEE) abgegeben werden. Wegen bedenklicher Substanzen,
die generell mit elektrischen und elektronischen Geräten in Verbindung stehen, könnte eine unsachgemäße Behandlung dieser Abfallart eine negative Auswirkung auf Umwelt und Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag zur richtigen Entsorgung dieses Produkts die effektive Nutzung natürlicher Ressourcen. Für weitere Informationen zur Entsorgung Ihrer Geräte bei einer Recycling-Stelle nehmen Sie bitte Kontakt zum zuständigen städtischen Büro, Entsorgungsamt oder zu Ihrem Haushaltsabfallentsorger auf.
HAFTUNGSAUSSCHLUSS
MUSIC Group übernimmt keine Haftung für Verluste, die Personen entstanden sind, die sich ganz oder teilweise auf hier enthaltene Beschreibungen, Fotos oder Aussagen verlassen haben. Technische Daten, Erscheinungsbild und andere Informationen können ohne vorherige Ankündigung geändert werden. Alle Warenzeichen sind Eigentum der jeweiligen Inhaber. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA und DDA sind Warenzeichen oder eingetragene Warenzeichen der MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Alle Rechte vorbehalten.
BESCHRÄNKTE GARANTIE
Die geltenden Garantiebedingungen und zusätzliche Informationen bezüglich der von MUSIC Group gewährten beschränkten Garantie fi nden Sie online unter music-group.com/warranty.
6
TCS Passive R series Quick Start Guide
7
Instruções de Segurança Importantes
Aviso!
Terminais marcados com o
símbolo carregam corrente elétrica de magnitude sufi ciente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes comercialmente disponíveis de alta qualidade com plugues TS de ¼" pré-instalados. Todas as outras instalações e modifi cações devem ser efetuadas por pessoas qualifi cadas.
Este símbolo, onde quer que o
encontre, alerta-o para a leitura
das instruções de manuseamento que acompanham o equipamento. Por favor leia o manual de instruções.
Atenção
De forma a diminuir o
risco de choque eléctrico, não remover a cobertura (ou a secção de trás). Não existem peças substituíveis por parte do utilizador no seu interior. Para esse efeito recorrer a um técnico qualifi cado.
Atenção
Para reduzir o risco de
incêndios ou choques eléctricos o aparelho não deve ser exposto à chuva nem à humidade. Além disso, não deve ser sujeito a salpicos, nem devem ser colocados em cima do aparelho objectos contendo líquidos, tais como jarras.
Atenção
Estas instruções de operação
devem ser utilizadas, em exclusivo, por técnicos de assistência qualifi cados. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação, salvo se possuir as qualifi -cações necessárias. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação. Só o deverá fazer se possuir as qualifi cações necessárias.
1. Leia estas instruções.
2. Guarde estas instruções.
3. Preste atenção a todos os avisos.
4. Siga todas as instruções.
5. Não utilize este dispositivo perto
de água.
6. Limpe apenas com um pano seco.
7. Não obstrua as entradas de ventilação.
Instale de acordo com as instruções do fabricante.
8. Não instale perto de quaisquer fontes de calor tais como radiadores, bocas de ar quente, fogões de sala ou outros aparelhos (incluindo amplifi cadores) que produzam calor.
9. Não anule o objectivo de segurança das fi chas polarizadas ou do tipo de ligação à terra. Uma fi cha polarizada dispõe de duas palhetas sendo uma mais larga do que a outra. Uma fi cha do tipo ligação à terra dispõe de duas palhetas e um terceiro dente de ligação à terra. A palheta larga ou o terceiro dente são fornecidos para sua segurança. Se a fi cha fornecida não encaixar na sua tomada, consulte um electricista para a substituição da tomada obsoleta.
10. Proteja o cabo de alimentação de pisadelas ou apertos, especialmente nas fi chas, extensões, e no local de saída da unidade. Certifi que-se de que o cabo eléctrico está protegido. Verifi que particularmente nas fi chas, nos receptáculos e no ponto em que o cabo sai do aparelho.
11. O aparelho tem de estar sempre conectado à rede eléctrica com o condutor de protecção intacto.
12. Se utilizar uma fi cha de rede principal ou uma tomada de aparelhos para desligar a unidade de funcionamento, esta deve estar sempre acessível.
13. Utilize apenas ligações/acessórios especifi cados pelo fabricante.
14. Utilize apenas com o carrinho, estrutura, tripé, suporte, ou mesa especifi cados pelo fabricante ou vendidos com o dispositivo.
Quando utilizar um carrinho, tenha cuidado ao mover o conjunto carrinho/dispositivo para evitar danos provocados pela terpidação.
15. Desligue este dispositivo durante as trovoadas ou quando não for utilizado durante longos períodos de tempo.
16. Qualquer tipo de reparação deve ser sempre efectuado por pessoal qualifi cado. É necessária uma reparação sempre que a unidade tiver sido de alguma forma danifi cada, como por exemplo: no caso do cabo de alimentação ou fi cha se encontrarem danifi cados; na eventualidade de líquido ter sido derramado ou objectos terem caído para dentro do dispositivo; no caso da unidade ter estado exposta à chuva ou à humidade; se esta não funcionar normalmente, ou se tiver caído.
17. Correcta eliminação deste produto: este símbolo indica que o produto não deve ser eliminado juntamente com os resíduos domésticos, segundo a Directiva REEE
(2012/19/EU) e a legislação nacional. Este produto deverá ser levado para um centro de recolha licenciado para a reciclagem de resíduos de equipamentos eléctricos e electrónicos (EEE). O tratamento incorrecto deste tipo de resíduos pode ter um eventual impacto negativo no ambiente e na saúde humana devido a substâncias potencialmente perigosas que estão geralmente associadas aos EEE. Ao mesmo tempo, a sua colaboração para a eliminação correcta deste produto irá contribuir para a utilização efi ciente dos recursos naturais. Para mais informação acerca dos locais onde poderá deixar o seu equipamento usado para reciclagem, é favor contactar os serviços municipais locais, a entidade de gestão de resíduos ou os serviços de recolha de resíduos domésticos.
LEGAL RENUNCIANTE
O MUSIC Group não se responsabiliza por perda alguma que possa ser sofrida por qualquer pessoa que dependa, seja de maneira completa ou parcial, de qualquer descrição, fotografi a, ou declaração aqui contidas. Dados técnicos, aparências e outras informações estão sujeitas a modifi cações sem aviso prévio. Todas as marcas são propriedade de seus respectivos donos. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA e DDA são marcas ou marcas registradas do MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Todos direitos reservados.
GARANTIA LIMITADA
Para obter os termos de garantia aplicáveis e condições e informações adicionais a respeito da garantia limitada do MUSIC group, favor verifi car detalhes na íntegra através do website music-group.com/warranty.
安全にお使いいただくために
注意
感電の.恐れがありますので、 カバーやその他の部品を取り
外したり、開けたりしないでください。高 品質なプロ用スピーカーケーブル(¼" TS 標準ケーブルおよびツイストロッキング プラグケーブル)を使用してください。
注意
火事および感電の危険を防ぐ
ため、本装置を水分や湿気の あるところには設置しないで下さい。装置 には決して水分がかからないように注意 し、花瓶など水分を含んだものは、装置の 上には置かないようにしてください。
注意
このマークが 表 示されている
箇所には、内部に高圧電流が 生じています。手を触れると感電の恐れが あります。
注意
取り扱いとお手入れの方法に
ついての重要な説明が付属の 取扱説明書に記載されています。ご使用の 前に良くお読みください。
注意
1. 取扱説明書を通してご覧ください。
2. 取扱説明書を大切に保管してくだ
さい。
3. 警告に従ってください。
4. 指示に従ってください。
5. 本機を水の近くで使用しないでくだ
さい。
6. お手入れの際は常に乾燥した布巾を使 ってくだ さい 。
7. 本機は、取扱説明書の指示に従い、 適切な換気を妨げない場所に設置してく ださい。取扱説明書に従って設置してくだ さい。
8. 本機は、電気ヒーターや温風機器、 ストーブ、調理台やアンプといった熱源か ら離して 設 置 してください 。
9. ニ極式プラグおよびアースタイプ (三芯)プラグの安全ピンは取り外さないで ください 。ニ極式プラグにはピンが二本つ いており、そのうち一本はもう一方よりも幅 が広くなっています。アースタイプの三 芯 プ ラグにはニ本のピンに加えてアース用のピ ンが一本ついています。これらの幅の広い ピン、およびアースピンは、安全のためのも のです。備え付けのプラグが、お使いのコン セントの形 状と異なる場合は 、電器技師に 相談してコンセントの交換をして下さい。
10. 電源コードを踏みつけたり、挟んだり しないようご注 意ください。電源コードや プラグ、コンセント及び製 品との接 続には 十分にご注意ください。
11. すべての装置の接地(アース)が確保 されていることを確認して下さい。
12. 電源タップや 電源プラグは電 源遮断機として利 用されている場合 には、これが直ぐ に操作できるよう 手元に設置して下 さい。
13. 付属品は本機
製造元が指定したもののみをお使いくだ さい。
14. カートスタンド、三脚、ブラケット、 テーブルなどは、本機製造元が指定したも の、もしくは本機 の 付属品となるもののみ をお使いください。カートを使用しての運 搬の際は、器具の落下による怪我に十分ご 注意ください。
15. 雷雨の場合、もしくは長 期 間ご 使 用 に ならない 場 合 は、電源プラグをコンセント から抜いてください。
16. 故障の際は当社指定のサービス技術 者にお問い合わせください。電源コードも しくはプラグの損 傷 、液体の装置内への浸 入、装置の上に物が落下した場合、雨や湿 気に装置が晒されてしまった場合、正常に 作動しない場合、もしくは装 置 を地 面 に 落 下させてしまった場 合など、いかなる形で あれ装置に損傷が加わった場合は、装置 の修理・点検を受けてください。
17. 本製品に電源コード が付属されている場合、 付属の電源コードは本製 品以外ではご使用いただ けません。電源コードは 必ず本製 品に付属された 電源コードのみご使用く ださい。
法的放棄
ここに含まれる記 述 、写真、意見の全体 または一部に依拠して、いかなる人が損害 を生じさせた場合にも、MUSIC Group は一切の賠償責任を負いません。 技術仕様、外観およびその他の情報は 予告なく変更になる場合があります。 商標はすべて、それぞれの所有者に帰 属します。MIDAS、KLARK TEKNIK、
TURBOSOUND、BEHRINGER、 BUGERAおよびDDAはMUSIC Group IP Ltd.の商標または登録商標で
す。© MUSIC Group IP Ltd. 2014 無断転用禁止。
限定保証
適用される保証条件とMUSIC Group の限定保証に関する概要については、 オンライン上music-group.com/warranty にて詳細をご確認ください。
8
TCS Passive R series Quick Start Guide
9
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further
information about this or any other TURBOSOUND product, please visit our website at turbosound.com.
Unpacking the Loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify your
supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future
re-shipment.
System Requirements – Passive and Bi-amped Loudspeakers
TCS62-R 2-way loudspeaker operates as a passive system and requires only one amplifi er channel.
The input signal is divided between the low-frequency and high-frequency drivers internally with a
passive crossover.
TCS122-R and TCS152-R are switchable passive / bi-amp 2-way loudspeakers. Passive and bi-amp modes
are controlled by an internal switch. Passive operation (full range or with a subwoofer) requires 1 amplifi er
channel and 1 controller channel. The input signal is divided between the low-frequency and high-
frequency drivers internally with a passive crossover. Bi-amp operation (full range or with a subwoofer)
requires 2 amplifi er channels and 2 controller channels, one for low frequencies one for high frequencies.
The input signal is divided between the low frequency and high frequency driver in the controller and the
individual amplifi ed signals are fed to the speaker input.
TCS218B-R subwoofer has a 4-wire input to allow operation in parallel or discrete modes. Parallel operation
is achieved by wiring inputs 1 and 2 in parallel and requires only 1 amplifi er channel and 1 controller
channel. Discrete operation is achieved by wiring inputs 1 and 2 separately, requiring 2 amplifi er channels
and 2 controller channels.
TCS115B subwoofer operates as a passive system and requires only one amplifi er channel.
Correct controller settings for all models, horn variants and operation with subwoofers can be downloaded
from the website, and are also available as presents for the LMS series controllers.
TCS weather-resistant loudspeakers are equipped with a 2 metre 4-core cable tail for connection to your
chosen cabling infrastructure, with the exception of TCS62-R and TCS115B-R, which use a 2-core cable tail.
To avoid wasting amplifi er power, you should use heavy-duty speaker cable, with a minimum wire size of
1.5 mm2 (16 AWG), and preferably 2.5 mm2 (14 AWG) for longer runs. Use larger wire sizes for TCS218B-R
and speakers wired in parallel. For extreme cable lengths, be aware of cable impedance and resistive
losses. Always observe the correct polarity.
᧙᜷ᄋ߸Мᮍᅽ
ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధ ܹᄋႄุߜڛᝐႄԁᬘǎᬎ Ώၺࣝధ ¼" TSᩛତ݁
ᄋᰵַ᠐˅ˋܧ٩ጴǎధᄋ߸ᜊួ ஠ڪᮍႁՍಬᄋ˅ˋցᤊᛢǎ
൦ಗ঄ଣᧉ১ַаߜڛఴ ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ
൦ಗ঄ଣᧉ১ಋ󰪀ᬅᄋ᧙᜷ ᄋΏၺԤ፦οឮ௛ǎឱ󰪀឵ధ Угǎ
࠶
˟ᥙГᝐႄԁᬘឱӉ఼
ᮈᄧᑁ᭨૖ౝǎ᝻ܭа෦ ధԼΚၺ፦οΏၺᄋᦋǎឱ࠳፦ο ᮋႁՍಬᄋ˅ˋցᤊᛢǎ
࠶
˟ᥙГᅍ༣ᝐႄԁᬘឱӉ
࠳൦᝻ܭᎷᭂ๹໾ິ˘ǎ ൦᝻ܭ˸ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ ٩˸ˁԼᎷЦʾݡᔊၬ኏ǎ
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘ᦢǎ
12. ឱԷΏၺԉࠓ
૊ࠁᄋᬥ᠏ᩚ ׭ᄋଏᢽ౷ߖ ʽᝉ౷஄౷֘ಹ ߖǎᔫΏၺଏᢽ ౐ୄᤃ᝻ܭឱญ ߸М஋Ꮇ᝻ܭ ᥙГଏᢽ֘᝻
ܭϛωᏬԫǎ
13. ᥆󰩧ႄᭈᲟ󰩤ఱˁΏၺశ᝻ܭ௒ ឱફѤႄ຺ତ݁ǎ
14. ధ፦οڪᮍႁՍಬᄋ፦οցᤊ ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴ ႄ຺ତ݁ԫ૰๰͵ุЛྮᗁЛ᝻ܭ а᝻ܭᥔᭂ๹ԫ໾᝻ܭˁᑠ൥ࣣᤃͼ ᜃ୒گǎ
15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ εઑǎ
16. ᔫႄ຺ତ݁٩Ч ᏺՍ٩ၺͼளႄᜊᎷ ε᝾߳ܬᬥ௒Լ ஶΨ୳ͼ࿅ঘǎ
17. శַᤡၺ๓ફ 2000ዜʿڢӞశַ ᤡၺ᭥མࣝජό౏ ʿǎ
ฃܧ௛
ࠬͶڃڛ൦ឮ௛˻ଣ҃ᄋМᦋ ᦋଢᤙǍڐྠܧ௛Ꮼᤶᄋ૰ ݀MUSIC Groupˁ᠈Ͷ᠋ǎ ઀సԡஞ֘ܲ᜻ᔫధటஉিˁԴᛢ ᤱᅽǎధᄋ׹ಗڪ˟ЦՋᒮధᏩ ᄋ᠊ǎMIDASKLARK TEKNIK TURBOSOUNDBEHRINGERBUGERA ֘DDA௨MUSIC Group IP Ltd.ОՄᄋ ׹ಗญг׹ಗǎ© MUSIC Group IP Ltd. 2014ྡీధǎ
εο౏൝
ధУᮄˮᬸڅεοᄋᤡၺ౏ ൝ԤЦ߳ᄲУθ্ឱᄇᬇ music-group.com/warranty Ꭻቤಋᄻߺ஠ᄋឡጻθ্ǎ
࠶
፦οឮ௛௨ፍՍಬᄋ˅ˋ፦
οցΏၺ ᄋǎ˟ᥙГᝐႄԁ ᬘᬕΏၺឮ௛˻ଣ҃ᄋܲឱӉᤊᛢ ͶЦ߳፦οǎధ፦οڪᮍႁՍಬᄋ˅ ˋցᤊᛢǎ
1. ឱ󰪀឵ᤉឮ௛ǎ
2. ឱݱؔεߜᤉឮ௛ǎ
3. ឱญధᄋ᝞ᇩǎ
4. ឱᥗ߷ధᄋឮ௛ǎ
5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַǎ
6. ឱၺࣱ࣌ຎพశַǎ
7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ௒ឱᥗ
ཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ߸ᜊڛམ຺ᬅᤄ ݡ఍ජྠ༰ߖЦ߳ၸམ᧛ᄋ᝻ܭ Ӌ઻ҫ஋٩ǎ
9. ឱӉሩᬕ౞মତ݁଍ڢତ݁ᄋ߸М ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕ ଍ڢ݁౟ǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১ ᄋତឱႄࢻట૲ʸ˕Սᤡᄋତǎ
10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇ҉ ᆢࡀЦญႄ຺ତ݁Ǎܴၺ᤮ତԤ᝻ܭ ᤍ଍ܬǎ
10
TCS Passive R series Quick Start Guide
11
Connections
TCS62-R
Amplifi er Considerations
The TCS series loudspeakers are optimised for use with the TURBOSOUND T series amplifi ers with the
LMS series controllers. A full range of DSP settings to suit any confi guration are provided for download
on the TURBOSOUND website. The use of third party amplifi cation and processing is only advised using
the matrix of manual settings as well as the limiter calculator provided on the TURBOSOUND website.
The TCS series loudspeaker enclosures should be driven by high quality power amplifi ers designed for
true professional use. Power amplifi ers should be capable of delivering long term broadband power equal
to half the loudspeaker’s peak power rating at its stated nominal impedance. The use of underpowered
amplifi ers must be avoided as heavily clipped signals can cause permanent loudspeaker damage.
Limiters, crossovers and equalisation points must be set in accordance with the settings provided on the
TURBOSOUND website. This will ensure the optimum sound quality and long-term reliability as well as
protection from damage.
2 meter 4-core cable tails are provided, allowing options for passive, bi-amp, parallel and discrete
operation, with the exception of TCS62-R and TCS115B-R, which use a 2-core cable tail.
Recommended Minimum Amplifi er Power
Outdoor Applications
TCS weather-resistant products are designed to provide robust protection against the elements when
used outdoors in harsh environments. The cabinet is fully sealed inside and out, protected with a weather-
resistant paint fi nish, and the plated and outdoor powder-coated perforated steel grille backed with
reticulated foam resists the impact of showers. Hard wired speaker connection is made via a 4 or 2-core
cable tail fi tted through a weather-sealed cable gland mounted on an aluminium connector plate. Stainless
steel external fi xings are used throughout. Internally, the drivers are treated to resist moisture absorption
while the internal corner brackets are zinc plated and outdoor powder-coated.
While TCS series loudspeakers with the “R” suffi x are constructed for outdoor use, care should be taken
when installing these loudspeakers outdoors in coastal areas where high salinity and extreme temperature
variations are present in addition to high humidity and UV light exposure.
Loudspeakers must always be mounted with a downward angle. Do not allow loudspeakers to become
fully immersed in water at any time. Routine inspection and maintenance programs must be carried out on
a regular basis and parts replaced as necessary to provide continued satisfactory performance.
Model TCS62-R TCS122-R TCS152-R TCS115B-R TCS218B-R
Mode Passive Passive Bi-amp LF Bi-amp LF Passive Bi-amp LF Bi-amp HF Passive Passive
Impedance 8 Ohms 8 Ohms 8 Ohms 6 Ohms 8 Ohms 8 Ohms 6 Ohms 8 Ohms 4 Ohms
Minimum Amplifi er Power
Continuous RMS
175 W 600 W 600 W 75 W 600 W 600 W 75 W 500 W 1600 W
Peak 700 W 2400 W 2400 W 750 W 2400 W 2400 W 750 W 2000 W 6400 W
Passive Only
HPF
HF
2-core cable tail
RED + BLUE -
> >
LPF
LF
Mode Back Panel Internal Schematic
Passive (Internal Switch)
Bi-Amp (Internal Switch)
HF
4-core cable tail
RED LOW +
BLUE LOW -
YELLOW HIGH +
GREEN HIGH -
> > > >
LF
HPF
HF
4-core cable tail
RED + BLUE -
YELLOW N/C
GREEN N/C
> >
>
>
LPF
LF
Mode Back Panel Internal Schematic
TCS122-R, TCS152-R
12
TCS Passive R series Quick Start Guide
13
Mounting and Fixing
The table below summarises the rigging parts or kits required for various applications, and some examples
of the possible rigging options are illustrated.
TCS series cabinets are designed with multiple internal rigging points to suit many possible mounting
methods in permanent installations. All cabinets can be simply suspended using optional M8 or M10
shoulder eyebolts coupled to the internal rigging points provided. Remove the appropriate countersunk
screws and replace them with eyebolts, which must have a thread length of at least 18mm. Use the rear
rigging point to angle the cabinet for optimum room coverage. Cabinets may be hung upside down if
required. Turbosound WB-20, WB-55 and CB-55 wall and ceiling brackets are optionally available for TCS
series cabinets, and these are also compatible with OmniMount* wall and ceiling brackets which use
60 mm x 60 mm hole spacing.
Some typical examples of the possible rigging options are shown here:
Model Wall Ceiling Downfi ll Array Kit Eyebolts
TCS62-R
WB-20
TCS62-SB
CB-55
TCS62-SB
TCS62-SB M8 Thread
TCS122-R WB-55 CB-55
TCS122-FP
TCS-FK1 TCS-FK2
EB-10-40
TCS152-R WB-55 CB-55
TCS152-FP
TCS-FK1 TCS-FK2
EB-10-40
TCS115B-R
TCS115-FP
TCS-FK3
EB-10-40
TCS-R Subwoofers EB-10-40
Passive
> >
LF
RED + BLUE -
2-core cable tail
Mode Back Panel Internal Schematic
Parallel or Discrete are configured with external connection
LF 1
> >
LF 2
4-core cable tail
RED SUB 1 +
BLUE SUB 1 -
YELLOW SUB 2 +
GREEN SUB 2 -
>
>
Mode Back Panel Internal Schematic
TCS115B-R
TCS218B-R
14
TCS Passive R series Quick Start Guide
15
TCS Series Flying Components
Wall and Ceiling Brackets
To install a loudspeaker using Turbosound wall and ceiling brackets, fi rst separate the brackets into their
wall/ceiling plate and speaker plate component parts. Remove the countersunk bolts on the rear panel of
the cabinet. Attach the speaker plate to the cabinet with the bolts supplied. Fix the wall/ceiling plate in the
venue using appropriate fi xings (not supplied). Lift the loudspeaker on to the wall plate and re-assemble
the bracket parts, adjust the vertical angle and tighten all bolts.
Downfi ll Applications
The TCS62-R can be mounted underneath a TCS122-R or TCS152-R
cabinet to provide downfi ll coverage using the TCS62-SB swivel bracket.
First disassemble the swivel bracket into its component parts. Remove
the countersunk bolts from the bottom panel of the TCS152-R cabinet
and fi t the section with the elongated holes using the fi xings supplied.
Remove the countersunk bolts on the top panel and fi t the swivel bracket
using the supplied fi xings. Re-assemble the swivel bracket, angle as
appropriate and tighten all fi xings.
To install the TCS62-R in a ceiling-mount application, separate the component parts as above, and fi x the
top section to the ceiling with appropriate fi xings (not supplied). Fit the other half to the TCS62-R cabinet,
re-assemble the bracket, angle as appropriate and tighten all fi xings.
Loudspeaker Arrays and Clusters
An array of two or more cabinets requires the use of kits of fl yplates and inter-cabinet couplers, which are
fi xed to the cabinet sides through the M10 rigging points and assembled together in a ‘daisy chain’ fashion
to build up the required array. For all loudspeaker arrays consisting of two or more cabinets:
The number of inter cabinet coupler kits required = the number of boxes – 1, The number of fl yplate kits
required = the number of boxes.
Illustrated here are the components parts available for TCS cabinets:
TCS62-SB SWIVEL BRACKET
TCS62-SB (WH) Swivel bracket for TCS62-R
Contents:
1 x Bracket
2 x M8 Bolts
2 x M8 Spring Washers
2 x M8 Flat Washers
TCS122-FP (WH) Fly Plate Kit for TCS122-R
Contents:
2 x Fly Plates
2 x M10 Bolts
2 x M10 Spring Washers
2 x M10 Flat Washers
TCS152-FP (WH) Fly Plate Kit for TCS152-R
Contents:
TCS115-FP (WH) Fly Plate Kit for TCS115B-R
Contents:
2 x Fly Plates
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
2 x Fly Plates
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
TCS-FK1 (WH) Inter-Cabinet Coupler Kit for TCS122-R or TCS152-R
Contents:
2 x ICC
TCS-FK2 (WH) Inter-Cabinet Coupler Kit for TCS122-R or TCS152-R
Contents:
2 x ICC
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
TCS-FK3 (WH) Inter-Cabinet Coupler Kit for TCS115B-R
Contents:
2 x ICC
EB-10-40 Eyebolt M10 x 40mm
Contents:
1 x Eyebolt
16
TCS Passive R series Quick Start Guide
17
Suspending with Eyebolts
TCS cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided on
the top, bottom and sides and back. The simplest method is to use the two rigging points on the top and a
single pull-back rigging point in the centre of the rear panel.
Remove the appropriate countersunk screws and replace them withshoulder eyebolts, which must have
a thread length of at least 18 mm. Use the rear rigging point to angle the cabinet for optimum room
coverage. Cabinets may be hung upside down if required.
IMPORTANT NOTE FOR ALL INSTALLATION METHODS: The mounting of a permanently installed sound system
may be dangerous unless undertaken by qualifi ed personnel with the required experience and certifi cation
to perform the necessary tasks. Walls, fl oors or ceilings must be capable of safely and securely supporting
the actual load. The mounting accessory used must be safely and securely fi xed both to the loudspeaker
and to the wall, fl oor or ceiling.
When mounting rigging components on walls, fl oors or ceilings, ensure that all fi xings and fasteners
used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and
composition of walls and ceilings, all need to be taken into account when determining whether a
particular fi xing arrangement can be safely employed for a particular load. Cavity plugs or other specialist
fi xings, if required, must be of an appropriate type, and must be fi tted and used in accordance with the
maker’s instructions.
The operation of your speaker cabinet as part of a fl own system, if installed incorrectly and improperly,
can potentially expose persons to serious health risks and even death. In addition, please ensure that
electrical, mechanical and acoustic considerations are discussed with qualifi ed and certifi ed (by local state
or national authorities) personnel prior to any installation or fl ying.
Make sure that speaker cabinets are set up and fl own by qualifi ed and certifi ed personnel only,
using dedicated equipment and original parts and components delivered with the unit. If any parts or
components are missing please contact your Dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group,
including the MUSIC Group companies listed on the enclosed “Service Information Sheet”, assumes no
liability for any damage or personal injury resulting from improper use, installation or operation of the
product. Regular checks must be conducted by qualifi ed personnel to ensure that the system remains in a
secure and stable condition. Make sure that, where the speaker is fl own, the area underneath the speaker is
free of human traffi c. Do not fl y the speaker in areas that can be entered or used by members of the public.
Speakers create a magnetic fi eld, even if not in operation. Therefore, please keep all materials that can
be affected by such fi elds (discs, computers, monitors, etc) at a safe distance. A safe distance is usually
between 1 and 2 metres.
Rotating the HF horn pattern
The high frequency horn in all TCS122-R and TCS152-R models can be rotated through 90° in order to swap
the horizontal and vertical dispersion patterns, particularly useful when assembling clusters or for example
to retain the original dispersion when the cabinet is installed in a horizontal orientation.
1. Place the cabinet on its back on a suitable work surface. Take care of the protruding cable gland.
2. Remove the 10 posi-drive screws that hold the grille in place and set the grille aside (fi g 1).
3. Remove and disconnect the bass driver (fi g 2) to access the compression driver retaining brace, making a
note of the bass driver polarity for later reconnection.
4. Reach in through the bass driver cavity and loosen the two wing nuts securing the compression driver
retaining brace (fi g 3).
5. Remove the horn fi xing screws that secure the horn to the enclosure and lift out the horn and
compression driver assembly (fi g 4). (If required for servicing or replacement, disconnect the cables from
the compression driver, making a note of the polarity for later reconnection.)
6. Rotate the horn to achieve the desired coverage pattern (fi g 5).
7. Re-assemble the cabinet and drivers by reversing steps 1-5.
8. If the compression driver cables have been disconnected, reconnect the cables while observing the
correct polarity (white cable to the +ve terminal, black cable to the –ve terminal).
9. Place the horn and compression driver back into the cabinet, making sure that the driver cables pass
underneath the compression driver retainer and that the compression driver fi ts squarely back into the
retaining brace.
10. Tighten the wing nuts back onto the compression driver retaining brace (fi g 3).
11. Replace the horn fi xing screws and tighten to secure the horn back into the enclosure (fi g 4).
12. Reconnect the bass driver cables, observing the correct polarity (red cable to the +ve terminal, blue cable
to the –ve terminal).
13. Check all components and confi rm the horn orientation is correct (fi g 6).
14. Replace the grille (fi g 1) and phase check the cabinet before use.
Fig. 1
Fig. 2 Fig. 3
BEFORE AFTER
Fig. 4 Fig. 5 Fig. 6
18
TCS Passive R series Quick Start Guide
19
Technical Specifi cations
TCS62-R (-WH) TCS122/64 -R (-WH) TCS122/94 -R (-WH) TCS122/96-R (-WH) TCS152/64 -R (-WH) TCS152/94-R (-WH) TCS152/96-R (-WH)
System
Frequency response
60 Hz - 20 kHz ±3 dB 50 Hz - 20 kHz -10 dB
50 Hz - 18 kHz ±3 dB 45 Hz - 20 kHz -10 dB
50 Hz - 18 kHz ±3 dB 45 Hz - 20 kHz -10 dB
50 Hz - 18 kHz ±3 dB 45 Hz - 20 kHz -10 dB
41 Hz - 18 kHz ±3 dB 35 Hz - 20 kHz -10 dB
41 Hz - 18 kHz ±3 dB 35 Hz - 20 kHz -10 dB
41 Hz - 18 kHz ±3 dB 35 Hz - 20 kHz -10 dB
Nominal dispersion
100° H x 60° V @ -6dB points, rotatable
60° H x 40° V @ -6 dB points, rotatable
90° H x 40° V @ -6 dB points, rotatable
90° H x 60° V @ -6 dB points, rotatable
60° H x 40° V @ -6 dB points, rotatable
90° H x 40° V @ -6 dB points, rotatable
90° H x 60° V @ -6 dB points, rotatable
Directivity factor (Q)
12.8 18.3 12.9 8.7 18.3 12.9 8.7
Directivity index (DI)
11.1 12.6 11.1 9.4 12.6 11.1 9.4
Power handling (IEC)
Passive 175 W continuous, 700 W peak 600 W continuous, 2400 W peak 600 W continuous, 2400 W peak 600 W continuous, 2400 W peak 600 W continuous, 2400 W peak 600 W continuous, 2400 W peak 600 W continuous, 2400 W peak
Bi-amp
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
LF:600 W continuous, 2400 W peak HF:75 W continuous, 300 W peak
Sensitivity
90 dB (1 W @ 1 m) 96 dB (1 W @ 1 m) 96 dB (1 W @ 1 m) 96 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m)
Maximum SPL
Passive 112.5 dB continuous, 118.5 dB peak 124 dB continuous, 130 dB peak 124 dB continuous, 130 dB peak 124 dB continuous, 130 dB peak 125 dB continuous, 131 dB peak 125 dB continuous, 131 dB peak 125 dB continuous, 131 dB peak
Bi-amp
LF: 124 dB continuous, 130 dB peak HF: 128 dB continuous, 134 dB peak
LF: 124 dB continuous, 130 dB peak HF: 128 dB continuous, 134 dB peak
LF: 124 dB continuous, 130 dB peak HF: 128 dB continuous, 134 dB peak
LF: 125 dB continuous, 131 dB peak HF: 128 dB continuous, 134 dB peak
LF: 125 dB continuous, 131 dB peak HF: 128 dB continuous, 134 dB peak
LF: 125 dB continuous, 131 dB peak HF: 128 dB continuous, 134 dB peak
Impedance
Passive 8 Ω 8 Ω 8 Ω 8 Ω 8 Ω 8 Ω 8 Ω
Bi-amp
LF: 8 Ω HF: 6 Ω
LF: 8 Ω HF: 6 Ω
LF: 8 Ω HF: 6 Ω
LF: 8 Ω HF: 6 Ω
LF: 8
Ω
HF: 6 Ω
LF: 8 Ω HF: 6 Ω
Crossover type
Passive
Passive / Bi-amp, internally switchable
Passive / Bi-amp, internally switchable
Passive / Bi-amp, internally switchable
Passive / Bi-amp, internally switchable
Passive / Bi-amp, internally switchable
Passive / Bi-amp, internally switchable
Components
1 x 6" (162 mm) LF driver 1 x 1" (25 mm) HF compression driver
1 x 12" (312 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
1 x 12" (312 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
1 x 12" (312 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
1 x 15" (394 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
1 x 15" (394 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
1 x 15" (394 mm) LF driver 1 x 1.4" (36 mm) HF compression driver
Enclosure
Connectors
2-core captive cable tail 4-core captive cable tail 4-core captive cable tail 4-core captive cable tail 4-core captive cable tail 4-core captive cable tail 4-core captive cable tail
Wiring
Passive Red/Blue input + / -
Red/Blue input + / - , Yellow/Green NC
Red/Blue input + / - , Yellow/Green NC
Red/Blue input + / - , Yellow/Green NC
Red/Blue input + / - , Yellow/Green NC
Red/Blue input + / - , Yellow/Green NC
Red/Blue input + / - , Yellow/Green NC
Bi-amp
Red/Blue LF + / -, Yellow/Green HF + / -
Red/Blue LF + / -, Yellow/Green HF + / -
Red/Blue LF + / -, Yellow/Green HF + / -
Red/Blue LF + / -, Yellow/Green HF + / -
Red/Blue LF + / -, Yellow/Green HF + / -
Red/Blue LF + / -, Yellow/Green HF + / -
Dimensions (HWD)
224 x 402 x 198 mm (18.8 x 15.8 x 7.8")
834 x 399 x 425 mm (32.8 x 15.7 x 16.7")
834 x 399 x 425 mm (32.8 x 15.7 x 16.7")
834 x 399 x 425 mm (32.8 x 15.7 x 16.7")
834 x 473 x 451 mm (32.8 x 18.6 x 17.8")
834 x 473 x 451 mm (32.8 x 18.6 x 17.8")
834 x 473 x 451 mm (32.8 x 18.6 x 17.8")
Net weight
7.3 kg (16.1 lbs) 26.9 kg (59.3 lbs) 26.9 kg (59.3 lbs) 26.9 kg (59.3 lbs) 28.6 kg (63.1 lbs) 28.6 kg (63.1 lbs) 28.6 kg (63.1 lbs)
Construction
12 mm (½") birch plywood 15 mm (
5
/8") birch plywood 15 mm (5/8") birch plywood 15 mm (5/8") birch plywood 15 mm (5/8") birch plywood 15 mm (5/8") birch plywood 15 mm (5/8") birch plywood
Finish
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Grille
Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel
Flying hardware
M8 X 8, M6 X 2 Points M10 x 9, M8 X 8 Points M10 x 9, M8 X 8 Points M10 x 9, M8 X 8 Points M10 x 9, M8 X 8 Points M10 x 9, M8 X 8 Points M10 x 9, M8 X 8 Points
Accessories
TCS62-SB (WH) swivel bracket for TCS62
TCS122-FP (WH) fl y plate kit for TCS122 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS122-FP (WH) fl y plate kit for TCS122 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS122-FP (WH) fl y plate kit for TCS122 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS152-FP (WH) fl y plate kit for TCS152 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS152-FP (WH) fl y plate kit for TCS152 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS152-FP (WH) fl y plate kit for TCS152 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
20
TCS Passive R series Quick Start Guide
21
Other important information
1. Register online. Please register your
new MUSIC Group equipment right after you purchase it by visiting turbosound. com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and effi ciently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction. Should your MUSIC Group Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fulfi ller for your country listed under “Support” at turbosound. com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at turbosound. com. Alternatively, please submit an online warranty claim at turbosound. com BEFORE returning the product.
3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.
Important information
Technical Specifi cations
TCS115B-R (-WH) TCS218B -R (-WH)
System
Frequency response
45 Hz - 150 Hz ± 3 dB 40 Hz - 200 Hz - 10 dB
33 Hz - 200 Hz ± 3 dB 27 Hz - 200 Hz - 10 dB
Nominal dispersion
Half space Half space
Power handling (IEC)
500 W continuous, 2000 W peak 1600 W continuous, 6400 W peak
Sensitivity
97 dB (1 W @ 1 m) 99 dB (1 W @ 1 m)
Maximum SPL
124 dB continuous, 130 dB peak 131 dB continuous, 137 dB peak
Impedance
8 Ω Parallel: 4 Ω Discrete: 8 Ω x 2
Components
1 x 15" (387 mm) LF driver 2 x 18" (460 mm) LF driver
Enclosure
Connectors
2-core captive cable tail 4-core captive cable tail
Wiring
Parallel / No switch Red/Blue input + / -
Red/Blue input + / -, Yellow/Green link + / -
Discrete
Red/Blue input 1 + / -, Yellow/Green input 2 + / -
Dimensions (HWD)
834 x 469 x 452 mm (32.9 x 18.5 x17.8")
1130 x 710 x 730 mm (44.5 x 28.0 x 28.8")
Net weight
33.9 kg (74.7 lbs) 94 kg (207.2 lbs)
Construction
15 mm (
5
/8") birch plywood 18 mm (5/8") birch plywood
Finish
Semi matt black paint (white optional)
Semi matt black paint (white optional)
Grille
Powder-coated perforated steel Powder-coated perforated steel
Flying hardware
M10 x 8 M10 x 8
Accessories
TCS115-FP (WH) fl y plate kit for TCS115B TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152 TCS-FK3 (WH) inter-cabinet coupler kit for TCS115B
Loading...