Turbosound TCS218B-AN, TCS122/96-AN, TCS115B-AN, TCS152/64, TCS122/64-AN Quick Start Guide

...

SERIES

TCS-AN

TCS122/64-AN (-WH), TCS122/94-AN (-WH), TCS122/96-AN (-WH), TCS152/64-AN (-WH), TCS152/94-AN (-WH), TCS152/96-AN (-WH), TCS115B-AN (WH), TCS218B-AN (WH)

Arrayable 2,500 Watt 2 Way Full Range Loudspeakers with Dendritic Waveguides 6,000 Watt and Arrayable 3,000 Watt Subwoofers KLARK TEKNIK DSP Technology and ULTRANET Networking

TCS-AN series Quick Start Guide

Important Safety Instructions

Terminals marked with this symbol carry electrical

current of sufﬁ cient magnitude to constitute risk of electric shock. Use only high-quality commercially-available speaker cables with plugs pre-installed. All other installation or modiﬁ cation should be performed only by qualiﬁ ed personnel.

This symbol, wherever it

appears, alerts you to the

presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufﬁ cient to constitute a risk of shock.

This symbol, wherever it

appears, alerts you to important

operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution

To reduce the risk of electric

shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualiﬁ ed personnel.

Caution

To reduce the risk of ﬁ re or

electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects ﬁ lled with liquids, such as vases, shall be placed on the apparatus.

Caution

These service instructions are

for use by qualiﬁ ed service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualiﬁ ed service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation

openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁ ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories speciﬁ ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU)

and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efﬁ cient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city ofﬁ ce, or your household waste collection service.

LEGAL DISCLAIMER

MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical speciﬁ cations, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC Group’s Limited Warranty, please see complete details online at music-group.com/warranty.

Instrucciones de seguridad

Las terminales marcadas con este símbolo transportan

corriente eléctrica de magnitud suﬁ ciente como para constituir un riesgo de descarga eléctrica. Utilice solo cables de altavoz de alta calidad con clavijas TS de 6,3 mm pre-instaladas (puede adquirirlos en comercios especializados en audio). Cualquier otra instalación o modiﬁ cación debe ser realizada únicamente por un técnico cualiﬁ cado.

Este símbolo, siempre que

aparece, le advierte de la

presencia de voltaje peligroso sin aislar dentro de la caja; este voltaje puede ser suﬁ ciente para constituir un riesgo de descarga.

Este símbolo, siempre que

aparece, le advierte sobre

instrucciones operativas y de mantenimiento que aparecen en la documentación adjunta. Por favor, lea el manual.

Atención

Para reducir el riesgo de

descarga eléctrica, no quite la tapa (o la parte posterior). No hay piezas en el interior del equipo que puedan ser reparadas por el usuario. Si es necesario, póngase en contacto con personal cualiﬁ cado.

Atención

Para reducir el riesgo de

incendio o descarga eléctrica, no exponga este aparato a la lluvia, humedad o alguna otra fuente que pueda salpicar o derramar algún líquido sobre el aparato. No coloque ningún tipo de recipiente para líquidos sobre el aparato.

Atención

Las instrucciones de servicio

deben llevarlas a cabo exclusivamente personal cualiﬁ cado. Para evitar el riesgo de una descarga eléctrica, no realice reparaciones que no se encuentren descritas en el manual de operaciones. Las reparaciones deben ser realizadas exclusivamente por personal cualiﬁ cado.

1. Lea las instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas

las advertencias.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Limpie este aparato con un paño seco.

7. No bloquee las aberturas de

ventilación. Instale el equipo de acuerdo con las instrucciones del fabricante.

8. No instale este equipo cerca de fuentes de calor tales como radiadores, acumuladores de calor, estufas u otros aparatos (incluyendo ampliﬁ cadores) que puedan producir calor.

9. No elimine o deshabilite nunca la conexión a tierra del aparato o del cable de alimentación de corriente. Un enchufe polarizado tiene dos polos, uno de los cuales tiene un contacto más ancho que el otro. Una clavija con puesta a tierra dispone de tres contactos: dos polos y la puesta a tierra. El contacto ancho y el tercer contacto, respectivamente, son los que garantizan una mayor seguridad. Si el enchufe suministrado con el equipo no concuerda con la toma de corriente, consulte con un electricista para cambiar la toma de corriente obsoleta.

10. Coloque el cable de suministro de energía de manera que no pueda ser pisado y que esté protegido de objetos aﬁ lados. Asegúrese de que el cable de suministro de energía esté protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato.

11. Use únicamente los dispositivos o accesorios especiﬁ cados por el fabricante.

12. Use únicamente la carretilla, plataforma, trípode, soporte o mesa especiﬁ cados por el fabricante o suministrados junto con el equipo.

Al transportar el equipo, tenga cuidado para evitar daños y caídas al tropezar con algún obstáculo.

13. Desenchufe el equipo durante tormentas o si no va a utilizarlo durante un periodo largo.

14. Confíe las reparaciones únicamente a servicios técnicos cualiﬁ cados. La unidad requiere mantenimiento siempre que haya sufrido algún daño, si el cable de suministro de energía o el enchufe presentaran daños, se hubiera derramado un líquido o hubieran caído objetos dentro del equipo, si el aparato hubiera estado expuesto a la humedad o la lluvia, si ha dejado de funcionar de manera normal o si ha sufrido algún golpe o caída.

15. Al conectar la unidad a la toma de corriente eléctrica asegúrese de que la conexión disponga de una unión a tierra.

16. Si el enchufe o conector de red sirve como único medio de desconexión, éste debe ser accesible fácilmente.

17. Cómo debe deshacerse de este aparato: Este símbolo indica que este aparato no debe ser tratado como basura orgánica, según lo indicado en la Directiva

WEEE (2012/19/EU) y a las normativas aplicables en su país. En lugar de ello deberá llevarlo al punto limpio más cercano para el reciclaje de sus elementos eléctricos / electrónicos (EEE). Al hacer esto estará ayudando a prevenir las posibles consecuencias negativas para el medio ambiente y la salud que podrían ser provocadas por una gestión inadecuada de este tipo de aparatos. Además, el reciclaje de materiales ayudará a conservar los recursos naturales. Para más información acerca del reciclaje de este aparato, póngase en contacto con el Ayuntamiento de su ciudad o con el punto limpio local.

NEGACIÓN LEGAL

MUSIC Group no admite ningún tipo de responsabilidad por cualquier daño o pérdida que pudiera sufrir cualquier persona por conﬁ ar total o parcialmente en la descripciones, fotografías o aﬁ rmaciones contenidas en este documento. Las especiﬁ caciones técnicas, imágenes y otras informaciones contenidas en este documento están sujetas a modiﬁ caciones sin previo aviso. Todas las marcas comerciales que aparecen aquí son propiedad de sus respectivos dueños. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA y DDA son marcas comerciales o marcas registradas de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Reservados todos los derechos.

GARANTÍA LIMITADA

Si quiere conocer los detalles y condiciones aplicables de la garantía así como información adicional sobre la Garantía limitada de MUSIC group, consulte online toda la información en la web music-group.com/warranty.

TCS-AN series Quick Start Guide

Consignes de sécurité

Les points repérés par ce symbole portent une tension

électrique sufﬁ sante pour constituer un risque d’électrocution. Utilisez uniquement des câbles d’enceintes de haute qualité disponibles dans les points de vente avec les connecteurs Jack mono 6,35 mm déjà installés. Toute autre installation ou modiﬁ cation doit être effectuée uniquement par un personnel qualiﬁ é.

Ce symbole avertit de la

présence d’une tension

dangereuse et non isolée à l’intérieur de l’appareil - elle peut provoquer des chocs électriques.

Attention

Ce symbol signale les

consignes d’utilisation et d’entre ! Tien importantes dans la documentation fournie. Lisez les consignes de sécurité du manuel d’utilisation de l’appareil.

Attention

Pour éviter tout risque de

choc électrique, ne pas ouvrir le capot de l’appareil ni démonter le panneau arrière. L’intérieur de l’appareil ne possède aucun élément réparable par l’utilisateur. Laisser toute réparation à un professionnel qualiﬁ é.

Attention

Pour réduire les risques de feu

et de choc électrique, n’exposez pas cet appareil à la pluie, à la moisissure, aux gouttes ou aux éclaboussures. Ne posez pas de récipient contenant un liquide sur l’appareil (un vase par exemple).

Attention

Ces consignes de sécurité et

d’entretien sont destinées à un personnel qualiﬁ é. Pour éviter tout risque de choc électrique, n’effectuez aucune réparation sur l’appareil qui ne soit décrite par le manuel d’utilisation. Les éventuelles réparations doivent être effectuées uniquement par un technicien spécialisé.

1. Lisez ces consignes.

2. Conservez ces consignes.

3. Respectez tous les avertissements.

4. Respectez toutes les consignes

d’utilisation.

5. N’utilisez jamais l’appareil à proximité d’un liquide.

6. Nettoyez l’appareil avec un chiffon sec.

7. Veillez à ne pas empêcher la bonne

ventilation de l’appareil via ses ouïes de ventilation. Respectez les consignes du fabricant concernant l’installation de l’appareil.

8. Ne placez pas l’appareil à proximité d’une source de chaleur telle qu’un chauffage, une cuisinière ou tout appareil dégageant de la chaleur (y compris un ampli de puissance).

9. Ne supprimez jamais la sécurité des prises bipolaires ou des prises terre. Les prises bipolaires possèdent deux contacts de largeur différente. Le plus large est le contact de sécurité. Les prises terre possèdent deux contacts plus une mise à la terre servant de sécurité. Si la prise du bloc d’alimentation ou du cordon d’ali-mentation fourni ne correspond pas à celles de votre installation électrique, faites appel à un électricien pour effectuer le changement de prise.

10. Installez le cordon d’alimentation de telle façon que personne ne puisse marcher dessus et qu’il soit protégé d’arêtes coupantes. Assurez-vous que le cordon d’alimentation est sufﬁsamment protégé, notamment au niveau de sa prise électrique et de l’endroit où il est relié à l’appareil; cela est également valable pour une éventuelle rallonge électrique.

11. Utilisez exclusivement des accessoires et des appareils supplémentaires recommandés par le fabricant.

12. Utilisez exclusivement des chariots, des diables, des présentoirs, des pieds et des surfaces de travail recommandés

par le fabricant ou livrés avec le produit. Déplacez précautionneusement tout chariot ou diable chargé pour éviter d’éventuelles blessures en cas de chute.

13. Débranchez l’appareil de la tension secteur en cas d’orage ou si l’appareil reste inutilisé pendant une longue période de temps.

14. Les travaux d’entretien de l’appareil doivent être effectués uniquement par du personnel qualiﬁé. Aucun entretien n’est nécessaire sauf si l’appareil est endommagé de quelque façon que ce soit (dommages sur le cordon d’alimentation ou la prise par exemple), si un liquide ou un objet a pénétré à l’intérieur du châssis, si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas correctement ou à la suite d’une chute.

15. L’appareil doit être connecté à une prise secteur dotée d’une protection par mise à la terre.

16. La prise électrique ou la prise IEC de tout appareil dénué de bouton marche/arrêt doit rester accessible en permanence.

17. Mise au rebut appropriée de ce produit: Ce symbole indique qu’en accord avec la directive DEEE (2012/19/EU) et les lois en vigueur dans votre pays, ce produit ne doit

pas être jeté avec les déchets ménagers. Ce produit doit être déposé dans un point de collecte agréé pour le recyclage des déchets d’équipements électriques et électroniques (EEE). Une mauvaise manipulation de ce type de déchets pourrait avoir un impact négatif sur l’environnement et la santé à cause des substances potentiellement dangereuses généralement associées à ces équipements. En même temps, votre coopération dans la mise au rebut de ce produit contribuera à l’utilisation efﬁ cace des ressources naturelles. Pour plus d’informations sur l’endroit où vous pouvez déposer vos déchets d’équipements pour le recyclage, veuillez contacter votre mairie ou votre centre local de collecte des déchets.

DÉNI LÉGAL

MUSIC Group ne peut être tenu pour responsable pour toute perte pouvant être subie par toute personne se ﬁ ant en partie ou en totalité à toute description, photographie ou afﬁ rmation contenue dans ce document. Les caractéristiques, l’apparence et d’autres informations peuvent faire l’objet de modiﬁ cations sans notiﬁ cation. Toutes les marques appartiennent à leurs propriétaires respectifs. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA et DDA sont des marques ou marques déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Tous droits réservés.

GARANTIE LIMITÉE

Pour connaître les termes et conditions de garantie applicables, ainsi que les informations supplémentaires et détaillées sur la Garantie Limitée de MUSIC Group, consultez le site Internet music-group.com/warranty.

Wichtige Sicherheitshinweise

Vorsicht

Die mit dem Symbol

markierten Anschlü sse fü hren so viel Spannung, dass die Gefahr eines Stromschlags besteht. Verwenden Sie nur hochwertige, im Handel erhältliche Lautsprecherkabel mit vorinstallierten 6,3 mm TSSteckern. Alle anderen Installationen oder Modiﬁ kationen sollten nur von qualiﬁ ziertem Fachpersonal ausgefü hrt werden.

Achtung

Um eine Gefährdung durch

Stromschlag auszuschließen, darf die Geräteabdeckung bzw. Geräterückwand nicht abgenommen werden. Im Innern des Geräts beﬁ nden sich keine vom Benutzer reparierbaren Teile. Reparaturarbeiten dürfen nur von qualiﬁ ziertem Personal ausgeführt werden.

Achtung

Um eine Gefährdung durch

Feuer bzw. Stromschlag auszuschließen, darf dieses Gerät weder Regen oder Feuchtigkeit ausgesetzt werden noch sollten Spritzwasser oder tropfende Flüssigkeiten in das Gerät gelangen können. Stellen Sie keine mit Flüssigkeit gefüllten Gegenstände, wie z. B. Vasen, auf das Gerät.

Achtung

Die Service-Hinweise sind nur

durch qualiﬁ ziertes Personal zu befolgen. Um eine Gefährdung durch Stromschlag zu vermeiden, führen Sie bitte keinerlei Reparaturen an dem Gerät durch, die nicht in der Bedienungsanleitung beschrieben sind. Reparaturen sind nur von qualiﬁ ziertem Fachpersonal durchzuführen.

1. Lesen Sie diese Hinweise.

2. Bewahren Sie diese Hinweise auf.

3. Beachten Sie alle Warnhinweise.

4. Befolgen Sie alle Bedienungshinweise.

5. Betreiben Sie das Gerät nicht in der

Nähe von Wasser.

6. Reinigen Sie das Gerät mit einem trockenen Tuch.

7. Blockieren Sie nicht die Belüftungsschlitze. Beachten Sie beim Einbau des Gerätes die Herstellerhinweise.

8. Stellen Sie das Gerät nicht in der Nähe von Wärmequellen auf. Solche Wärmequellen sind z. B. Heizkörper, Herde oder andere Wärme erzeugende Geräte (auch Verstärker).

9. Entfernen Sie in keinem Fall die Sicherheitsvorrichtung von Zweipol- oder geerdeten Steckern. Ein Zweipolstecker hat zwei unterschiedlich breite Steckkontakte. Ein geerdeter Stecker hat zwei Steckkontakte und einen dritten Erdungskontakt. Der breitere Steckkontakt oder der zusätzliche Erdungskontakt dient Ihrer Sicherheit. Falls das mitgelieferte Steckerformat nicht zu Ihrer Steckdose passt, wenden Sie sich bitte an einen Elektriker, damit die Steckdose entsprechend ausgetauscht wird.

10. Verlegen Sie das Netzkabel so, dass es vor Tritten und scharfen Kanten geschützt ist und nicht beschädigt werden kann. Achten Sie bitte insbesondere im Bereich der Stecker, Verlängerungskabel und an der Stelle, an der das Netzkabel das Gerät verlässt, auf ausreichenden Schutz.

11. Das Gerät muss jederzeit mit intaktem Schutzleiter an das Stromnetz angeschlossen sein.

12. Sollte der Hauptnetzstecker oder eine Gerätesteckdose die Funktionseinheit zum Abschalten sein, muss diese immer zugänglich sein.

13. Verwenden Sie nur Zusatzgeräte/ Zubehörteile, die laut Hersteller geeignet sind.

14. Verwenden Sie nur Wagen, Standvorrichtungen, Stative, Halter oder Tische, die vom Hersteller benannt oder im Lieferumfang des

Geräts enthalten sind. Falls Sie einen Wagen benutzen, seien Sie vorsichtig beim Bewegen der Wagen- Gerätkombination, um Verletzungen durch Stolpern zu vermeiden.

15. Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gerät längere Zeit nicht benutzen.

16. Lassen Sie alle Wartungsarbeiten nur von qualiﬁ ziertem Service-Personal ausführen. Eine Wartung ist notwendig, wenn das Gerät in irgendeiner Weise beschädigt wurde (z. B. Beschädigung des Netzkabels oder Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, das Gerät nicht ordnungsgemäß funktioniert oder auf den Boden gefallen ist.

17. Korrekte Entsorgung dieses Produkts: Dieses Symbol weist darauf hin, das Produkt entsprechend der WEEE Direktive (2012/19/EU) und der jeweiligen nationalen

Gesetze nicht zusammen mit Ihren Haushaltsabfällen zu entsorgen. Dieses Produkt sollte bei einer autorisierten Sammelstelle für Recycling elektrischer und elektronischer Geräte (EEE) abgegeben werden. Wegen bedenklicher Substanzen,

die generell mit elektrischen und elektronischen Geräten in Verbindung stehen, könnte eine unsachgemäße Behandlung dieser Abfallart eine negative Auswirkung auf Umwelt und Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag zur richtigen Entsorgung dieses Produkts die effektive Nutzung natürlicher Ressourcen. Für weitere Informationen zur Entsorgung Ihrer Geräte bei einer Recycling-Stelle nehmen Sie bitte Kontakt zum zuständigen städtischen Büro, Entsorgungsamt oder zu Ihrem Haushaltsabfallentsorger auf.

HAFTUNGSAUSSCHLUSS

MUSIC Group übernimmt keine Haftung für Verluste, die Personen entstanden sind, die sich ganz oder teilweise auf hier enthaltene Beschreibungen, Fotos oder Aussagen verlassen haben. Technische Daten, Erscheinungsbild und andere Informationen können ohne vorherige Ankündigung geändert werden. Alle Warenzeichen sind Eigentum der jeweiligen Inhaber. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA und DDA sind Warenzeichen oder eingetragene Warenzeichen der MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Alle Rechte vorbehalten.

BESCHRÄNKTE GARANTIE

Die geltenden Garantiebedingungen und zusätzliche Informationen bezüglich der von MUSIC Group gewährten beschränkten Garantie ﬁ nden Sie online unter music-group.com/warranty.

TCS-AN series Quick Start Guide

Instruções de Segurança Importantes

Aviso!

Terminais marcados com o

símbolo carregam corrente elétrica de magnitude suﬁ ciente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes comercialmente disponíveis de alta qualidade com plugues TS de ¼" pré-instalados. Todas as outras instalações e modiﬁ cações devem ser efetuadas por pessoas qualiﬁ cadas.

Este símbolo, onde quer que o

encontre, alerta-o para a leitura

das instruções de manuseamento que acompanham o equipamento. Por favor leia o manual de instruções.

Atenção

De forma a diminuir o

risco de choque eléctrico, não remover a cobertura (ou a secção de trás). Não existem peças substituíveis por parte do utilizador no seu interior. Para esse efeito recorrer a um técnico qualiﬁ cado.

Atenção

Para reduzir o risco de

incêndios ou choques eléctricos o aparelho não deve ser exposto à chuva nem à humidade. Além disso, não deve ser sujeito a salpicos, nem devem ser colocados em cima do aparelho objectos contendo líquidos, tais como jarras.

Atenção

Estas instruções de operação

devem ser utilizadas, em exclusivo, por técnicos de assistência qualiﬁ cados. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação, salvo se possuir as qualiﬁ -cações necessárias. Para evitar choques eléctricos não proceda a reparações ou intervenções, que não as indicadas nas instruções de operação. Só o deverá fazer se possuir as qualiﬁ cações necessárias.

1. Leia estas instruções.

2. Guarde estas instruções.

3. Preste atenção a todos os avisos.

4. Siga todas as instruções.

5. Não utilize este dispositivo perto

de água.

6. Limpe apenas com um pano seco.

7. Não obstrua as entradas de ventilação.

Instale de acordo com as instruções do fabricante.

8. Não instale perto de quaisquer fontes de calor tais como radiadores, bocas de ar quente, fogões de sala ou outros aparelhos (incluindo ampliﬁ cadores) que produzam calor.

9. Não anule o objectivo de segurança das ﬁ chas polarizadas ou do tipo de ligação à terra. Uma ﬁ cha polarizada dispõe de duas palhetas sendo uma mais larga do que a outra. Uma ﬁ cha do tipo ligação à terra dispõe de duas palhetas e um terceiro dente de ligação à terra. A palheta larga ou o terceiro dente são fornecidos para sua segurança. Se a ﬁ cha fornecida não encaixar na sua tomada, consulte um electricista para a substituição da tomada obsoleta.

10. Proteja o cabo de alimentação de pisadelas ou apertos, especialmente nas ﬁ chas, extensões, e no local de saída da unidade. Certiﬁ que-se de que o cabo eléctrico está protegido. Veriﬁ que particularmente nas ﬁ chas, nos receptáculos e no ponto em que o cabo sai do aparelho.

11. O aparelho tem de estar sempre conectado à rede eléctrica com o condutor de protecção intacto.

12. Se utilizar uma ﬁ cha de rede principal ou uma tomada de aparelhos para desligar a unidade de funcionamento, esta deve estar sempre acessível.

13. Utilize apenas ligações/acessórios especiﬁ cados pelo fabricante.

14. Utilize apenas com o carrinho, estrutura, tripé, suporte, ou mesa especiﬁ cados pelo fabricante ou vendidos com o dispositivo.

Quando utilizar um carrinho, tenha cuidado ao mover o conjunto carrinho/dispositivo para evitar danos provocados pela terpidação.

15. Desligue este dispositivo durante as trovoadas ou quando não for utilizado durante longos períodos de tempo.

16. Qualquer tipo de reparação deve ser sempre efectuado por pessoal qualiﬁ cado. É necessária uma reparação sempre que a unidade tiver sido de alguma forma daniﬁ cada, como por exemplo: no caso do cabo de alimentação ou ﬁ cha se encontrarem daniﬁ cados; na eventualidade de líquido ter sido derramado ou objectos terem caído para dentro do dispositivo; no caso da unidade ter estado exposta à chuva ou à humidade; se esta não funcionar normalmente, ou se tiver caído.

17. Correcta eliminação deste produto: este símbolo indica que o produto não deve ser eliminado juntamente com os resíduos domésticos, segundo a Directiva REEE

(2012/19/EU) e a legislação nacional. Este produto deverá ser levado para um centro de recolha licenciado para a reciclagem de resíduos de equipamentos eléctricos e electrónicos (EEE). O tratamento incorrecto deste tipo de resíduos pode ter um eventual impacto negativo no ambiente e na saúde humana devido a substâncias potencialmente perigosas que estão geralmente associadas aos EEE. Ao mesmo tempo, a sua colaboração para a eliminação correcta deste produto irá contribuir para a utilização eﬁ ciente dos recursos naturais. Para mais informação acerca dos locais onde poderá deixar o seu equipamento usado para reciclagem, é favor contactar os serviços municipais locais, a entidade de gestão de resíduos ou os serviços de recolha de resíduos domésticos.

LEGAL RENUNCIANTE

O MUSIC Group não se responsabiliza por perda alguma que possa ser sofrida por qualquer pessoa que dependa, seja de maneira completa ou parcial, de qualquer descrição, fotograﬁ a, ou declaração aqui contidas. Dados técnicos, aparências e outras informações estão sujeitas a modiﬁ cações sem aviso prévio. Todas as marcas são propriedade de seus respectivos donos. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA e DDA são marcas ou marcas registradas do MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2015 Todos direitos reservados.

GARANTIA LIMITADA

Para obter os termos de garantia aplicáveis e condições e informações adicionais a respeito da garantia limitada do MUSIC group, favor veriﬁ car detalhes na íntegra através do website music-group.com/warranty.

安全にお使いいただくために

注意

感電の.恐れがありますので、 カバーやその他の部品を取り

外したり、開けたりしないでください。高品質なプロ用スピーカーケーブル（¼" TS 標準ケーブルおよびツイストロッキング プラグケーブル）を使用してください。

注意

火事および感電の危険を防ぐ

ため、本装置を水分や湿気のあるところには設置しないで下さい。装置には決して水分がかからないように注意し、花瓶など水分を含んだものは、装置の上には置かないようにしてください。

注意

このマークが表示されている

箇所には、内部に高圧電流が生じています。手を触れると感電の恐れがあります。

注意

取り扱いとお手入れの方法に

ついての重要な説明が付属の取扱説明書に記載されています。ご使用の前に良くお読みください。

注意

1. 取扱説明書を通してご覧ください。

2. 取扱説明書を大切に保管してくだ

さい。

3. 警告に従ってください。

4. 指示に従ってください。

5. 本機を水の近くで使用しないでくだ

さい。

6. お手入れの際は常に乾燥した布巾を使ってください。

7. 本機は、取扱説明書の指示に従い、適切な換気を妨げない場所に設置してください。取扱説明書に従って設置してください。

8. 本機は、電気ヒーターや温風機器、ストーブ、調理台やアンプといった熱源から離して設置してください。

9. ニ極式プラグおよびアースタイプ (三芯)プラグの安全ピンは取り外さないでください。ニ極式プラグにはピンが二本ついており、そのうち一本はもう一方よりも幅が広くなっています。アースタイプの三芯プラグにはニ本のピンに加えてアース用のピンが一本ついています。これらの幅の広いピン、およびアースピンは、安全のためのものです。備え付けのプラグが、お使いのコンセントの形状と異なる場合は、電器技師に相談してコンセントの交換をして下さい。

10. 電源コードを踏みつけたり、挟んだりしないようご注意ください。電源コードやプラグ、コンセント及び製品との接続には十分にご注意ください。

11. すべての装置の接地(アース)が確保されていることを確認して下さい。

12. 電源タップや電源プラグは電源遮断機として利用されている場合には、これが直ぐに操作できるよう手元に設置して下さい。

13. 付属品は本機

製造元が指定したもののみをお使いください。

14. カートスタンド、三脚、ブラケット、テーブルなどは、本機製造元が指定したもの、もしくは本機の付属品となるもののみをお使いください。カートを使用しての運搬の際は、器具の落下による怪我に十分ご注意ください。

15. 雷雨の場合、もしくは長期間ご使用にならない場合は、電源プラグをコンセントから抜いてください。

16. 故障の際は当社指定のサービス技術者にお問い合わせください。電源コードもしくはプラグの損傷、液体の装置内への浸入、装置の上に物が落下した場合、雨や湿気に装置が晒されてしまった場合、正常に作動しない場合、もしくは装置を地面に落下させてしまった場合など、いかなる形であれ装置に損傷が加わった場合は、装置の修

理

・点検を受けてください。

17. 本製品に電源コードが付属されている場合、付属の電源コードは本製品以外ではご使用いただけません。電源コードは必ず本製品に付属された電源コードのみご使用ください。

法的放棄

ここに含まれる記述、写真、意見の全体または一部に依拠して、いかなる人が損害を生じさせた場合にも、MUSIC Group は一切の賠償責任を負いません。技術仕様、外観およびその他の情報は予告なく変更になる場合があります。商標はすべて、それぞれの所有者に帰属します。MIDAS、KLARK TEKNIK、

TURBOSOUND、BEHRINGER、 BUGERAおよびDDAはMUSIC Group IP Ltd.の商標または登録商標で

す。© MUSIC Group IP Ltd. 2015 無断転用禁止。

限定保証

適用される保証条件とMUSIC Group の限定保証に関する概要については、 オンライン上music-group.com/warranty にて詳細をご確認ください。

TCS-AN series Quick Start Guide

᧙᜷ᄋ߸Мᮍᅽ

ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధ ܹᄋႄุߜڛᝐႄԁᬘǎᬎ Ώၺࣝధ ¼" TSᩛତ݁

ᄋᰵַ᠐˅ˋܧ٩ጴǎధᄋ߸ᜊួ ஠ڪᮍႁՍಬᄋ˅ˋցᤊᛢǎ

൦ಗ঄ଣᧉ১ַаߜڛఴ ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ

൦ಗ঄ଣᧉ১ಋ󰪀ᬅᄋ᧙᜷ ᄋΏၺԤ፦οឮ௛ǎឱ󰪀឵ధ Угǎ

࠶

˟ᥙГᝐႄԁᬘឱӉ఼

ᮈᄧᑁ᭨૖ౝǎ᝻ܭа෦ ధԼΚၺ፦οΏၺᄋᦋǎឱ࠳፦ο ᮋႁՍಬᄋ˅ˋցᤊᛢǎ

࠶

˟ᥙГᅍ༣ᝐႄԁᬘឱӉ

࠳൦᝻ܭᎷᭂ๹໾ິ˘ǎ ൦᝻ܭ˸ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ ٩˸ˁԼᎷЦʾݡᔊၬ኏ǎ

11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘ᦢǎ

12. ឱԷΏၺԉࠓ

૊ࠁᄋᬥ᠏ᩚ ׭ᄋଏᢽ౷ߖ ʽᝉ౷஄౷֘ಹ ߖǎᔫΏၺଏᢽ ౐ୄᤃ᝻ܭឱญ ߸М஋Ꮇ᝻ܭ ᥙГଏᢽ֘᝻

ܭϛωᏬԫǎ

13. ᥆󰩧ႄᭈᲟ󰩤ఱˁΏၺశ᝻ܭ௒ ឱફѤႄ຺ତ݁ǎ

14. ధ፦οڪᮍႁՍಬᄋ፦οցᤊ ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴ ႄ຺ତ݁ԫ૰๰͵ุЛྮᗁЛ᝻ܭ а᝻ܭᥔᭂ๹ԫ໾᝻ܭˁᑠ൥ࣣᤃͼ ᜃ୒گǎ

15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ εઑǎ

16. ᔫႄ຺ତ݁٩Ч ᏺՍ٩ၺͼளႄᜊᎷ ε᝾߳ܬᬥ௒Լ ஶΨ୳ͼ࿅ঘǎ

17. శַᤡၺ๓ફ 2000ዜʿڢӞశַ ᤡၺ᭥མࣝජό౏ ʿǎ

ฃܧ௛

ࠬͶڃڛ൦ឮ௛˻ଣ҃ᄋМᦋ ᦋଢᤙǍڐྠܧ௛Ꮼᤶᄋ૰ ݀MUSIC Groupˁ᠈Ͷ᠋ǎ ઀సԡஞ֘ܲ᜻ᔫధటஉিˁԴᛢ ᤱᅽǎధᄋ׹ಗڪ˟ЦՋᒮధᏩ ᄋ᠊ǎMIDASKLARK TEKNIK TURBOSOUNDBEHRINGERBUGERA ֘DDA௨MUSIC Group IP Ltd.ОՄᄋ ׹ಗญг׹ಗǎ© MUSIC Group IP Ltd. 2015ྡీధǎ

εο౏൝

ధУᮄˮᬸڅεοᄋᤡၺ౏ ൝ԤЦ߳ᄲУθ্ឱᄇᬇ music-group.com/warranty Ꭻቤಋᄻߺ஠ᄋឡጻθ্ǎ

Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further

information about this or any other TURBOSOUND product, please visit our website at turbosound.com.

Unpacking the Loudspeaker

After unpacking the unit please check carefully for damage. If damage is found, please notify your

supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of

future re-shipment.

Controls

(1) (2)

(3)

(4)

(5)

(8) (9)

(10) (11)

(12)

(13)

࠶

፦οឮ௛௨ፍՍಬᄋ˅ˋ፦

οցΏၺ ᄋǎ˟ᥙГᝐႄԁ ᬘᬕΏၺឮ௛˻ଣ҃ᄋܲឱӉᤊᛢ ͶЦ߳፦οǎధ፦οڪᮍႁՍಬᄋ˅ ˋցᤊᛢǎ

1. ឱ󰪀឵ᤉឮ௛ǎ

2. ឱݱؔεߜᤉឮ௛ǎ

3. ឱญధᄋ᝞ᇩǎ

4. ឱᥗ߷ధᄋឮ௛ǎ

5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַǎ

6. ឱၺࣱ࣌ຎพశַǎ

7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ௒ឱᥗ

ཱིԉࠓᄋឮ௛ǎ

8. ឱӉ࠳శַ߸ᜊڛམ຺ᬅᤄ ݡ఍ජྠ༰ߖЦ߳ၸམ᧛ᄋ᝻ܭ Ӌ઻ҫ஋٩ǎ

9. ឱӉሩᬕ౞মତ݁଍ڢତ݁ᄋ߸М ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕ ଍ڢ݁౟ǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১ ᄋତឱႄࢻట૲ʸ˕Սᤡᄋତǎ

10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇ҉ ᆢࡀЦญႄ຺ତ݁Ǎܴၺ᤮ତԤ᝻ܭ ᤍ଍ܬǎ

(6)

(7)

TCS-AN series Quick Start Guide

(1) LCD SCREEN displays the current DSP module and parameter settings.

(2) SETUP button steps through parameters within DSP processing modules.

(3) PROCESS button steps through the DSP processing modules.

(4) AUDIO LINK XLR connector provides an un-processed copy of the AUDIO INPUT signal.

(5) AUDIO INPUT combo jack accepts input signals using XLR, balanced ¼" TRS or unbalanced

¼" TS connectors.

(6) POWER switch turns the unit on and off.

(7) AC INPUT accepts power connections from power cables ﬁ tted with Neutrik powerCON

twist-locking connectors.

(8) ENCODER KNOB toggles between Graphic and Edit modes (when pressed) and changes parameter

values (when rotated).

(9) EXIT button returns to the top-level DSP screen when pressed.

(10) ENTER button saves changes and deactivates Edit mode when pressed.

(11) ULTRANET THRU sends out unprocessed digital audio from the ULTRANET IN connector to additional

ULTRANET-equipped devices.

(12) USB connection enables ﬁ rmware updates and remote control over parameters via computer.

Please visit turbosound.com to download DSP control software for your computer.

(13) ULTRANET IN RJ45/Neutrik etherCON jack for connection to additional ULTRANET-equipped devices.

Networking capability

All TCS-AN powered loudspeakers offer remote control via USB. The USB connection allows the user to

conﬁ gure and monitor all DSP parameters using dedicated software for PC.

The DSP ﬁ rmware can also be updated via the USB connection. Visit turbosound.com for the latest

ﬁ rmware version.

TCS-AN speakers also offer proprietary ULTRANET networking capabilities through the ULTRANET IN and

ULTRANET THRU connections using CAT5 cables with RJ45 connectors. ULTRANET allows the user to

transmit unidirectionally up to 16 independent channels of 24-bit audio throughout the TCS-AN system,

as well as other ULTRANET-equipped devices such as digital mixers and personal monitor systems.

Up to 7 devices can be connected in series on a single ULTRANET cable.

MIDAS DL16

MIDAS M32

TCS-AN series Quick Start Guide

TCS-AN DSP Menu Structure

Fullrange Subwoofer Function

PROCESS

None None

Sets the frequency response to the default setting.

Array2 -

Sets a corrected frequency response for 2 cabinets arrayed together.

Array3 -

Sets a corrected frequency response for 3 or more cabinets arrayed together.

User User

Lets you deﬁ ne your own frequency response setting by entering the corresponding sub-menu.

Sub menu

Low/ High Shelving Low/ High Shelving

Lets you deﬁ ne a low and high shelving ﬁ lter.

Parametric 1 & 2 Parametric 1 & 2

Lets you deﬁ ne a parametric bell-type EQ (Frequency, Qual. and Gain).

XOVER

None -

Unit is set for default full-range reproduction.

HP 100 Hz LP 100 Hz

Preset with 100 Hz, 24 dB/octave ﬁ lter for crossover between subwoofer and full-range speakers.

HP 120 Hz LP 120 Hz

Preset with 120 Hz, 24 dB/octave ﬁ lter for crossover between subwoofer and full-range speakers.

User User

User crossover sub menu for combination with other full-range or subwoofer speaker systems

Sub Menu

Freq Freq

Select the desired crossover frequency:

• Fullrange Systems: 75 Hz to 400 Hz.

• Subwoofer Systems: 50 Hz to 150 Hz.

Phase Phase

Adjust the absolute phase (0° or 180°).

FBQ

Auto Auto

Automatically sets as many ﬁ lters as required. Whenever a new feedback frequency is discovered, the ﬁ rst ﬁ lter will be released to attenuate the new frequency, and so forth.

Single Single

Activates the FBQ (feedback detection) functionality, up to 8 feedback ﬁ lters.

Learn Learn

Automatic procedure which searches for feedback frequencies and locks settings after all 8 ﬁ lters have been set.

WARNING!

Please use ear protection during this procedure. The feedback signal may approach the system's maximum level, which may cause hearing damage!

Reset Reset

Resets all ﬁ lters.

SETUP

(page 1)

INPUT

Input Input

Lets you choose the audio input source. Choose between Local (analogue Input) or ULTRANET (e.g., P16 monitoring system or M32 audio via ULTRANET).

Fullrange Subwoofer Function

Volume Volume

Adjusts the input gain. With ULTRANET digital inputs over a range from + 10 dB to - 30 dB. With analogue input from 0 dB to - ∞ dB.

Sensitivity

Adjusts input sensitivity for maxium output when using an analogue source +4 dBu for normal opperation, + 14 dBu for high level input.

POSITION

Free -

For positioning the speaker in free suspension or ground stacked away from walls.

Wall Floor

For positioning the speaker on or next to a wall, or on the ﬂ oor (subwoofer)

Ceiling Wall

For positioning the speaker near the ceiling and wall, or ﬂ oor and wall (subwoofer)

Corner Corner

For positioning the speaker in a corner next to the ceiling (ﬁ xed install) or in a corner on the ﬂ oor (subwoofer)

Screenshot update

DELAY

Delay Delay

Adjusts the amount of delay (max 300 msec = 103 m or 338 feet).

Unit Unit

Selects between msec, meters and feet.

LIMITER

Limit Limit

Adjust the limiter threshold for the input signal (from OFF up to -30 dB). This threshold adjustment allows you to set a max output power which is below the loudspeaker system’s rated max output.

SETUP

(page 2)

Version Version

Displays the installed ﬁ rmware version.

LOAD

1. - 20. 1. - 20.

To load a speciﬁ c preset, turn the encoder to select the desired preset's number, and then press either the ENTER button or the encoder. When asked to conﬁ rm press the encoder again or EXIT to abort.

SAVE

1. - 20. 1. - 20.

To save a preset choose the respective preset slot and press ENTER or the encoder.

Sub Menu

Save Preset Save Preset

Name the preset by choosing the characters with the encoder and pressing to conﬁ rm each character. When ﬁ nished, press the ENTER button to save the preset.

SETUP

Contrast Contrast

Adjust LCD panel contrast. The default contrast value is 15.

Screen Screen

ON: LCD screen saver (default) turns on automatically after approx. 2 minutes.

OFF : LCD turns off automatically after approx. 5 minutes.

TCS-AN series Quick Start Guide

Mounting and Fixing

The table below summarises the rigging parts or kits required for various applications, and some examples

of the possible rigging options are illustrated.

TCS-AN series cabinets are designed with multiple internal rigging points to suit many possible mounting

methods in permanent installations. All cabinets can be simply suspended using optional M8 or M10

shoulder eyebolts coupled to the internal rigging points provided. Remove the appropriate countersunk

screws and replace them with eyebolts, which must have a thread length of at least 18mm. Use the rear

rigging point to angle the cabinet for optimum room coverage. Cabinets may be hung upside down if

required. Turbosound WB-55 and CB-55 wall and ceiling brackets are optionally available for TCS-AN

series cabinets, and these are also compatible with industry standard wall and ceiling brackets which use

60 mm x 60 mm hole spacing.

Some typical examples of the possible rigging options are shown here:

Model Wall Ceiling Downﬁ ll Array Kit Eyebolts

TCS122 WB-55 CB-55

TCS122-FP TCS-FK1 TCS-FK2

EB-10-40

TCS152

WB-55 CB-55

TCS152-FP TCS-FK1 TCS-FK2

EB-10-40

TCS115B

TCS115-FP TCS-FK3

EB-10-40

TCS Subwoofers EB-10-40

Fullrange Subwoofer Function

Sub Menu

Lock Lock

Lock the device and create a password by choosing the password characters with the encoder and pressing to conﬁ rm each character. When ﬁ nished press the ENTER button. Unlock the device by entering the password or connecting the unit via USB to a PC running proprietary remote software. The software does not require a password.

Warning Warning

In case of overheating, an alert appears on the LCD screen, and the ampliﬁ er will shut down until the unit cools

LCD Graphic Indicators

To help the user immediately recognize that a parameter has been selected and changed from the initial

default setting, the parameter’s related text on the top-level screen will invert and change to black text on a

white background. As an example, the following screenshots show how the text for the EQ function

changes when the TCS-AN default EQ setting has been changed:

This indicator function occurs only on the main DSP menu level and works for all DSP-related functions,

except for the LOAD, SAVE and SETUP sub-sections on the second page of the top-level SETUP menu.

TCS-AN series Quick Start Guide

TCS-AN Series Flying Components

Wall and Ceiling Brackets

To install a loudspeaker using Turbosound wall and ceiling brackets, ﬁ rst separate the brackets into their

wall/ceiling plate and speaker plate component parts. Remove the countersunk bolts on the rear panel of

the cabinet. Attach the speaker plate to the cabinet with the bolts supplied. Fix the wall/ceiling plate in the

venue using appropriate ﬁ xings (not supplied). Lift the loudspeaker on to the wall plate and re-assemble

the bracket parts, adjust the vertical angle and tighten all bolts.

Loudspeaker Arrays and Clusters

An array of two or more cabinets requires the use of kits of ﬂ yplates and inter-cabinet couplers, which are

ﬁ xed to the cabinet sides through the M10 rigging points and assembled together in a ‘daisy chain’ fashion

to build up the required array. For all loudspeaker arrays consisting of two or more cabinets:

The number of inter cabinet coupler kits required = the number of boxes – 1, The number of ﬂ yplate kits

required = the number of boxes.

Illustrated here are the components parts available for TCS cabinets:

TCS122-FP (WH) Fly Plate Kit for TCS122

TCS115-FP (WH) Fly Plate Kit for TCS115B

TCS152-FP (WH) Fly Plate Kit for TCS152

4 x M10 Bolts

4 x M10 Spring Washers

4 x M10 Flat Washers

4 x M10 Bolts

4 x M10 Spring Washers

4 x M10 Flat Washers

4 x M10 Bolts

4 x M10 Spring Washers

Contents:

2 x Fly Plates

Contents:

2 x Fly Plates

TCS-FK1 (WH) Inter-Cabinet Coupler Kit for TCS122 or TCS152

Contents:

2 x ICC

TCS-FK2 (WH) Inter-Cabinet Coupler Kit for TCS122 or TCS152

Contents:

2 x ICC

TCS-FK3 (WH) Inter-Cabinet Coupler Kit for TCS115B

Contents:

2 x ICC

EB-10-40 Eyebolt M10 x 40mm

Contents:

1 x Eyebolt

TCS-AN series Quick Start Guide

Suspending with Eyebolts

TCS-AN cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided

on the top, bottom and sides and back. The simplest method is to use the two rigging points on the top and

a single pull-back rigging point in the centre of the rear panel.

Remove the appropriate countersunk screws and replace them withshoulder eyebolts, which must have

a thread length of at least 18 mm. Use the rear rigging point to angle the cabinet for optimum room

coverage. Cabinets may be hung upside down if required.

IMPORTANT NOTE FOR ALL INSTALLATION METHODS: The mounting of a permanently installed sound system

may be dangerous unless undertaken by qualiﬁ ed personnel with the required experience and certiﬁ cation

to perform the necessary tasks. Walls, ﬂ oors or ceilings must be capable of safely and securely supporting

the actual load. The mounting accessory used must be safely and securely ﬁ xed both to the loudspeaker

and to the wall, ﬂ oor or ceiling.

When mounting rigging components on walls, ﬂ oors or ceilings, ensure that all ﬁ xings and fasteners

used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and

composition of walls and ceilings, all need to be taken into account when determining whether a

particular ﬁ xing arrangement can be safely employed for a particular load. Cavity plugs or other specialist

ﬁ xings, if required, must be of an appropriate type, and must be ﬁ tted and used in accordance with the

maker’s instructions.

The operation of your speaker cabinet as part of a ﬂ own system, if installed incorrectly and improperly,

can potentially expose persons to serious health risks and even death. In addition, please ensure that

electrical, mechanical and acoustic considerations are discussed with qualiﬁ ed and certiﬁ ed (by local state

or national authorities) personnel prior to any installation or ﬂ ying.

Make sure that speaker cabinets are set up and ﬂ own by qualiﬁ ed and certiﬁ ed personnel only,

using dedicated equipment and original parts and components delivered with the unit. If any parts or

components are missing please contact your Dealer before attempting to set up the system.

Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group,

including the MUSIC Group companies listed on the enclosed “Service Information Sheet”, assumes no

liability for any damage or personal injury resulting from improper use, installation or operation of the

product. Regular checks must be conducted by qualiﬁ ed personnel to ensure that the system remains in a

secure and stable condition. Make sure that, where the speaker is ﬂ own, the area underneath the speaker is

free of human trafﬁ c. Do not ﬂ y the speaker in areas that can be entered or used by members of the public.

Speakers create a magnetic ﬁ eld, even if not in operation. Therefore, please keep all materials that can

be affected by such ﬁ elds (discs, computers, monitors, etc) at a safe distance. A safe distance is usually

between 1 and 2 metres.

Rotating the HF horn pattern

The high frequency horn in all TCS122 and TCS152 models can be rotated through 90° in order to swap the

horizontal and vertical dispersion patterns, particularly useful when assembling clusters or for example to

retain the original dispersion when the cabinet is installed in a horizontal orientation.

1. Place the cabinet on its back on a suitable work surface.

2. Remove the 10 posi-drive screws that hold the grille in place and set the grille aside (ﬁ g 1).

3. Remove and disconnect the bass driver (ﬁ g 2) to access the compression driver retaining brace, making a

note of the bass driver polarity for later reconnection.

4. Reach in through the bass driver cavity and loosen the two wing nuts securing the compression driver

retaining brace (ﬁ g 3).

5. Remove the horn ﬁ xing screws that secure the horn to the enclosure and lift out the horn and

compression driver assembly (ﬁ g 4). (If required for servicing or replacement, disconnect the cables from

the compression driver, making a note of the polarity for later reconnection.)

6. Rotate the horn to achieve the desired coverage pattern (ﬁ g 5).

7. Re-assemble the cabinet and drivers by reversing steps 1-5.

8. If the compression driver cables have been disconnected, reconnect the cables while observing the

correct polarity (white cable to the +ve terminal, black cable to the –ve terminal).

9. Place the horn and compression driver back into the cabinet, making sure that the driver cables pass

underneath the compression driver retainer and that the compression driver ﬁ ts squarely back into the

retaining brace.

10. Tighten the wing nuts back onto the compression driver retaining brace (ﬁ g 3).

11. Replace the horn ﬁ xing screws and tighten to secure the horn back into the enclosure (ﬁ g 4).

12. Reconnect the bass driver cables, observing the correct polarity (red cable to the +ve terminal, blue cable

to the –ve terminal).

13. Check all components and conﬁ rm the horn orientation is correct (ﬁ g 6).

14. Replace the grille (ﬁ g 1) and phase check the cabinet before use.

Fig. 1

Fig. 2 Fig. 3

BEFORE AFTER

Fig. 4 Fig. 5 Fig. 6

TCS-AN series Quick Start Guide

Technical Speciﬁ cations

TCS122/64-AN (-WH) TCS122/94 -AN (-WH) TCS122/96 -AN (-WH) TCS152/64 -AN (-WH)

System

Frequency response

50 Hz – 18 kHz ±3 dB 45 Hz – 20 kHz -10 dB

41 Hz – 18 kHz ±3 dB 35 Hz – 20 kHz -10 dB

Nominal dispersion

60° H x 40° V @ -6 dB points, rotatable

90° H x 40° V @ -6 dB points, rotatable

90° H x 60° V @ -6 dB points, rotatable

60° H x 40° V @ -6 dB points, rotatable

Maximum SPL

131 dB peak 131 dB peak 131 dB peak 133 dB peak

Crossover type

Active Active Active Active

Transducers

1 x 12" (312 mm) LF Driver 1 x 1.4" (36 mm) HF compression driver

1 x 15" (394 mm) LF Driver 1 x 1.4" (36 mm) HF compression driver

Limiter

Independent HF, LF, peak and rms

Ampliﬁ er

Maximum output power*

2500 W 2500 W 2500 W 2500 W

Type

Class-D Class-D Class-D Class-D

Protection

Short circuit, thermal Short circuit, thermal Short circuit, thermal Short circuit, thermal

Connectors

Input/link

1 x Combo Jack/XLR, 1 x XLR

1 x Combo Jack/XLR 1 x XLR

Sensitivity

+4dBu or +14 dBu software switchable

Input impedance 40 kΩ balanced 40 kΩ balanced 40 kΩ balanced 40 kΩ balanced

Maximum input level +22 dBu +22 dBu +22 dBu +22 dBu

Ultranet input/link

2 x RJ45 2 x RJ45 2 x RJ45 2 x RJ45

Mains Supply

Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A

Controls

DSP

Rotary push-encoder and level control Buttons for Process, Setup, Exit, Enter

User DSP Func tion s

Factory EQ Presets

Positioning, Sound mode, FBQ

Display

LCD 128 x 32, blue, backlit

Delay

0 - 300 ms 0 - 300 ms 0 - 300 ms 0 - 300 ms

Equalisation

High and low shelving EQ 2 x parametric EQ

Limiter

Zero attack input limiter Zero attack input limiter Zero attack input limiter Zero attack input limiter

Presets

20 total presets, 19 user-deﬁ nable

Crossover

High Pass L-R 24 dB/oct High Pass L-R 24 dB/oct High Pass L-R 24 dB/oct High Pass L-R 24 dB/oct

Protection

Lock-out function for all settings

TCS122/64-AN (-WH) TCS122/94 -AN (-WH) TCS122/96 -AN (-WH) TCS152/64 -AN (-WH)

Ultranet Digital Network

Digital processing

A/D conversion Converter type

24-bit,44.1/48kHz sample rate 24-bit,delta-sigma

System

Signal Latency Frequency response Dynamic range

16 channels < 0.9 ms 20 Hz to 20 kHz (+0 / -3 dB) typical 92 dB

Cabling

Cables Shielded CAT5 Shielded CAT5 Shielded CAT5 Shielded CAT5

Cable length

max. 246 ft / 75 m recommended

Power Supply

Power consumption

90 W @

/8 max power 90 W @ 1/8 max power 90 W @ 1/8 max power 90 W @ 1/8 max power

Voltage (fuses)

USA / Canada

120 V~, 60 Hz (T 15 A H 250 V)

UK / Australia / Europe

220-240 V~, 50/60 Hz (T 10 A H 250 V)

Korea / China

220-240 V~, 50/60 Hz (T 10 A H 250 V)

Japan

100 V~, 50/60 Hz (T 15 A H 250 V)

Enclosure

Dimensions HWD

834 x 399 x 425 mm (32.8 x 15.7 x 16.7")

834 x 473 x 451 mm (32.8 x 18.6 x 17.8")

Net weight

27.8 kg (61.2 lbs) 27.8 kg (61.2 lbs) 27.8 kg (61.2lbs) 30.6 kg (67.3 lbs)

Construction

15 mm (

/8")

Birch plywood

15 mm (5/8") Birch plywood

Finish

Semi matt black paint (white optional)

Grille

Powder coated perforated steel

Flying hardware

M10 x 9, M8 X 8 points M10 x 9, M8 X 8 points M10 x 9, M8 X 8 points M10 x 9, M8 X 8 points

Accessories

TCS122-FP (-WH) Fly plate kit for TCS122

TCS152-FP (-WH) Fly plate kit for TCS152

TCS-FK1 (-WH) Intercabinet coupler kit for TCS122 or TCS152

TCS-FK2 (-WH) Intercabinet coupler kit for TCS115B with TCS122 or TCS152

TCS-AN series Quick Start Guide

Technical Speciﬁ cations

TCS152/94-AN (-WH) TCS152/96-AN (-WH) TCS115B-AN (WH) TCS218B-AN (WH)

System

Frequency response

41 Hz – 18 kHz ±3 dB 35 Hz – 20 kHz -10 dB

45 Hz – 150 Hz ±3 dB 40 Hz – 200 Hz -10 dB

33 Hz – 200 Hz ±3 dB 27 Hz – 200 kHz -10 dB

Nominal dispersion

90° H x 40° V @ -6 dB points, rotatable

90° H x 60° V @ -6 dB points, rotatable

Half Space Half Space

Maximum SPL

133 dB peak 133 dB peak 133 dB peak 141 dB peak

Crossover type

Active Active Active Active

Transducers

1 x 15" (394 mm) LF Driver 1 x 1.4" (36 mm) HF compression driver

1 x 15" (387 mm) LF driver /

2 x 18" (460 mm) LF driver /

Limiter

Independent HF, LF, peak and rms

Peak and rms Peak and rms

Ampliﬁ er

Maximum output power*

2500 W 2500 W 3000 W 6000 W

Type

Class-D Class-D Class-D Class-D

Protection

Short circuit, thermal Short circuit, thermal Short circuit, thermal Short circuit, thermal

Connectors

Input/link

1 x Combo Jack/XLR 1 x XLR

Sensitivity

+4dBu or +14 dBu software switchable

Input impedance 40 kΩ balanced 40 kΩ balanced 40 kΩ balanced 40 kΩ balanced

Maximum input level +22 dBu +22 dBu +22 dBu +22 dBu

Ultranet input/link

2 x RJ45 2 x RJ45 2 x RJ45 2 x RJ45

Mains Supply

Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A

Controls

DSP

Rotary push-encoder and level control Buttons for Process, Setup, Exit, Enter

User DSP Func tion s

Factory EQ Presets

Positioning, Sound mode, FBQ

Positioning, Sound mode

Display

LCD 128 x 32, blue, backlit

Delay

0 - 300 ms 0 - 300 ms 0 - 300 ms 0 - 300 ms

Equalisation

High and low shelving EQ 2 x parametric EQ

Limiter

Zero attack input limiter Zero attack input limiter Zero attack input limiter Zero attack input limiter

Presets

20 total presets, 19 user-deﬁ nable

Crossover

High Pass L-R 24 dB/oct High Pass L-R 24 dB/oct Low Pass L-R 24 dB/oct Low Pass L-R 24 dB/oct

Protection

Lock-out function for all settings

TCS152/94-AN (-WH) TCS152/96-AN (-WH) TCS115B-AN (WH) TCS218B-AN (WH)

Ultranet Digital Network

Digital processing

A/D conversion Converter type

24-bit,44.1/48kHz sample rate 24-bit,delta-sigma

System

Signal Latency Frequency response Dynamic range

16 channels < 0.9 ms 20 Hz to 20 kHz (+0 / -3 dB) typical 92 dB

Cabling

Cables Shielded CAT5 Shielded CAT5 Shielded CAT5 Shielded CAT5

Cable length

max. 246 ft / 75 m recommended

Power Supply

Power consumption

90 W @

/8 max power 90 W @ 1/8 max power 180 W @ 1/8 max power 350 W @ 1/8 max power

Voltage (fuses)

USA / Canada

120 V~, 60 Hz (T 15 A H 250 V)

UK / Australia / Europe

220-240 V~, 50/60 Hz (T 10 A H 250 V)

Korea / China

220-240 V~, 50/60 Hz (T 10 A H 250 V)

Japan

100 V~, 50/60 Hz (T 15 A H 250 V)

Enclosure

Dimensions HWD

834 x 473 x 451 mm (32.8 x 18.6 x 17.8")

834 x 469 x 452 mm (32.8 x 18.5 x 17.8")

710 x 1130 x 730 mm (28 x 44.5 x 28.7")

Net weight

30.6 kg (67.3 lbs) 30.6 kg (67.3 lbs) 34.5 kg (75.9 lbs) 95.5 kg (210.1 lbs)

Construction

15 mm (

/8")

Birch plywood

15 mm (5/8") Birch plywood

18 mm (5/8") Birch plywood

Finish

Semi matt black paint (white optional)

Grille

Powder coated perforated steel

Flying hardware

M10 x 9, M8 X 8 points M10 x 9, M8 X 8 points M10 x 8 M10 x 8

Accessories

TCS152-FP (-WH) Fly plate kit for TCS152

TCS115-FP (-WH) Fly plate kit for TCS115B

TCS-FK1 (-WH) Intercabinet coupler kit for TCS122 or TCS152

TCS-FK2 (-WH) Intercabinet coupler kit for TCS115B with TCS122 or TCS152

TCS-FK3 (-WH) Intercabinet coupler kit for TCS115B

*independent of limiters and driver protection circuits †Only qualiﬁ ed personnel are allowed to modify the AC-Main cord and to adhere to all applicable national standards.

TCS-AN series Quick Start Guide

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: MUSIC Group Services NV Inc.

Address: 5270 Procyon Street

Las Vegas, NV 89118 USA

Phone Number: +1 702 800 8290

TCS-AN Series

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• • Reorient or relocate the receiving antenna.

• • Increase the separation between the equipment and receiver.

• • Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• • Consult the dealer or an experienced radio/TV

technician for help.

This equipment complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Important information:

Changes or modiﬁ cations to the equipment not expressly approved by MUSIC Group can void the user’s authority to use the equipment.

TCS-AN Series

Other important information

1. Register online. Please register your

new MUSIC Group equipment right after you purchase it by visiting turbosound. com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efﬁ ciently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your MUSIC Group Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fulﬁ ller for your country listed under “Support” at turbosound. com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at turbosound. com. Alternatively, please submit an online warranty claim at turbosound. com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

Important information

TURBOSOUND

Turbosound TCS218B-AN, TCS122/96-AN, TCS115B-AN, TCS152/64, TCS122/64-AN Quick Start Guide

Specifications and Main Features

Frequently Asked Questions

User Manual