Turbo Force terminator 120V Operating Instructions Manual
TERMINATOR
https://harrissupplyind.com - To Order Parts Call 608-268-8080
INFORMATION
&
OPERATING
INSTRUCTIONS
120V
CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ
ALL SECTIONS OF THIS INSTRUCTION MANUAL
IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.
2. Before each use, remove the spray tool from the hose, and check to make sure the spray
nozzles are securely tightened to the spray tool. A loose nozzle could fly off during use.
3. Keep machine from r ain and snow , extr emes in temperatures, and stor e in a heated
location. Use the machine indoors. Do not use outdoors.
4. Never allow the spray to remain fixed in one spot.
5. Use approved chemicals only. NO SOL VENTS.
6. Never use this machine to strip finish from floors.
7. Never use water above 130º F/54º C in the solution tank.
8. Always use your pre-filter bag and keep both it and all other filters clean.
56041962
4-2010
IMPORTANT SAFETY INSTRUCTIONS
https://harrissupplyind.com - To Order Parts Call 608-268-8080
This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,
shops and offices other than normal residential housekeeping purposes.
When using any electrical appliance, basic precautions should always be followed, including the
following:
NOTE: Read all instructions before using this machine.
WARNING!
To reduce the risk of fire, electric shock, or injury:
• Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet
when not in use and before servicing.
• To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.
• Do not allow to be used as a toy. Close attention is necessary when used near children.
• Use only as described in this manual. Use only the manufacturer’s recommended attachments.
• Never add water over 130º F/54º C to the solution tank.
• Do not use with damaged cord or plug. If the machine is not working as it should, has been
dropped, damaged, left outdoors or dropped into water, return it to a service center.
• Protect the cord. Do not: use the cord as a handle, close a door on the cord, or pull the cord
around sharp edges or corners. Do not run the machine over the cord. K eep the cord a wa y f r om
heated surfaces. To unplug, grasp the plug, not the cord.
• Do not handle the plug, the cord or the machine with wet hands.
• Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug
immediately if the ground prong becomes damaged.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
• Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or
any health endangering dusts. Do not use to pick up flammable or combustible liquids such as
gasoline or use in areas where they may be present.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Connect to a properly grounded outlet only.
• Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure, or
chemical content.
SAVE THESE INSTRUCTIONS
INSPECTION:
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Carefully unpack and inspect your TERMINA TOR f or shipping damage. Each machine is tested and inspected
before shipping. Any shipping damage incurred is the responsibilit y of the carrier . Y ou should notify the carrier
immediately if you notice damage to the box or to the machine or parts.
CLEANING SOLUTIONS:
Select a proper pre-spray for the surf ace to be cleaned, and apply the pre-spray. Use a neutral pH rinse or
detergent (6 to 10 pH) in the King Cobra to prevent premature wear of the pumps, seals, and other components.
Damage caused by the use of improper or harsh chemicals is not covered by warranty. Powders are not
recommended.
MAINTENANCE:
For optimum performance, flush the machine with clear water at the end of each working day . Alw ays use the
pre-filter bag and keep it and both pump inlet filters clean. Once a month, minimum, run a flushing compound
through the machine to break up any mineral or chemical bui ld-up that may have formed. The vacuum motor,
pump motors, and the pumps do not require any scheduled maintenance; however, the motors may require
replacement brushes after 1000 - 1500 hours, and the high pressure pump and unloader valve may require
rebuild kits after 500 -1000 hours (refer to machine part list for numbers). Clean the body with an all purpose
detergent, and protect it with an automobile interior polish. Lubricate the wheels, castors, and quick disconnects
with an all purpose silicone spray .
Record the serial number and model of your new extractor here:
(and be sure to register your purchase to activate your warranty)
Serial Number: __________________ Model: TERMINATOR
Purchase Date:
Write the name and phone number of your distributor:
____________________________________________________________________
____________________________________________________________________
_____________
SAVE THESE INSTRUCTIONS
KNOW YOUR MACHINE
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Latch
Solution
Tank
Vacuum
Hose
Connection
Hoses
Recovery
Tank Lid
Wand Holder
Switches
Recovery
Tank
1200 PSI
Quick
Disconnect
Auto-fill
Hose
Connector
Wheel
Base
Compartment
Recovery Tank
Dump Hose
Recepticle
Wheel
150 psi
Quick Disconnect
Wand Holder
Recovery
Tank
Power
Cord
Vacuum Hose
Connection
Auto-Dump
Pump
Castor
Power Prime
Pedal
Loading...