OWNER’ S MANUAL
83 1/2"
RLM-855WS
45 1/4"
Lat Machine W/200 Lbs Steel
Weight Stack
AMERICA’S PREMIER EXERCISE EQUIPMENT
64 3/4"
RLM-855WS Rev0
Revision Date 5-30-2007
Introduction
About the Lat Machine W/200 Lbs Steel Weight Stack
RLM-855WS
Congratulations on your new purchase of the Lat Machine W/200
Lbs Steel Weight Stack. We hope you are completely satisfi ed
with this product and wish you many years of enjoyment.
Tuff Stuff Equipment
This Tuffstuff product has been built to precise quality standards
and has been carefully packaged to ensure that damage will not
occur during shipment. The Home Lifetime Warranty and signature
indicating fi nal inspection has been conducted by our line foreman,
is an expression of our confi dence in the completeness, the
materials, and workmanship of this product.
Warranty
SEE A COPY OF WARRANTY ON BACK PAGE.
Registration Card
To avoid unnecessary delays in warranty service and to insure that
a permanent record of your purchase is on fi le with our factory,
be sure to complete the warranty registration card and send it to
TuffStuff Fitness Equipment today.
Specifi cations
1. Maximum Wt. Capacity - 200 lbs.
2. Total Machine Weight - 375 lbs.
3. Footprint (LWH) - See Front Cover.
Note: Due to continuing product improvements, specifi cations and designs are subject to change
without notice.
Prior to the Assembly of the Lat Machine W/200 Lbs Steel
Weight Stack
1. We advise you to consult your local Tuff Stuff retailer if you should
have a question or problem regarding the proper assembly of
this unit.
Tool Requirements
1. One 7/8” combination wrench
2. One 3/4” combination wrench
3. One 9/16” combination wrench
4. One ratchet
5. One 9/16” socket
6. One rubber mallet
7. Windex or household glass cleaner
8. Measuring tape
9. Utility knife
Hardware Measurement Diagram
H
T
G
N
E
L
W
E
R
C
S
R
E
H
S
A
W
H
T
D
I
WW
E
R
C
S
R
E
T
E
M
A
I
D
R
E
T
E
M
A
I
D
T
U
N
Step 1 Assembly List
Item # Description Qty.
1 REINFORCEMENT PLATE 1/4 X 2 X 7 1
3 BASE FRAME 1
7 FOOT ROLL TUBE 1 X 16 1
13 LOW ROW FOOT SUPPORT 1
15 STABILIZER 1
33 FLAT WASHER SAE Z/P 3/8” 4
40 HEX HEAD CAP SCREW 3/8-16 X 5 2
47 NYLON INSERT JAM LOCK NUT 3/8-16 2
49 PLASTIC ELLIPTICAL SHOE 2
51 PLASTIC INSERT CAP 1” RD 10-12 GA 2
63 SOCKET SET SCREW 3/8-16 X 3/4 1
51
63
13
7
47
3
33
51
49
47
1
33
15
33
40
33
49
2 RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
Step 2 Assembly List
Item # Description Qty.
4 BENCH FRAME 1
5 CENTER POST 1
6 FOAM FOOT ROLL 1 X 4 X 7 2
9 HOLD DOWN T BAR 1
20 ALUMINUM WASHER .390 ID X 1.500 2
24 BUTTON HEAD SCREW 3/8-16 X 1 2
33 FLAT WASHER SAE 3/8” 8
34 FOAM ROLL 1” NYLINER BUSHING 4
35 HEX HEAD CAP SCREW 3/8-16 X 1 4
38 HEX HEAD CAP SCREW 3/8-16 X 2 3/4 2
47 NYLON INSERT JAM LOCK NUT 3/8-16 2
66 SPLIT LOCK WASHER 3/8” 6
24
66
20
34
5
34
6
34
20
66
24
33
6
35
66
33
34
9
35
66
33
4
38
38
33
33
35
66
33
47
33
35
66
33
3
3RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
35
66
16
66
33
38
33
66
Step 3 Assembly List
Item # Description Qty.
8 GUIDE ROD 3/4 X 73 1/8 2
10 LAT BAR HOLDER 1
14 SELECTOR PIN W/COIL 3/8 X 4 1
16 TOP ASSEMBLY 1
18 10 LB STEEL WEIGHT PLATE BLACK 19
19 10 LB TOP PLATE W/22” SLTR BAR 1
30 DECAL-WEIGHT NUMBERS 1
33 FLAT WASHER SAE 3/8” 7
35 HEX HEAD CAP SCREW 3/8-16 X 1 7
38 HEX HEAD CAP SCREW 3/8-16 X 2 3/4 2
57 RUBBER DONUT 3/4 X 2 1/2 2
66 SPLIT LOCK WASHER 3/8” 7
8
8
10
33
33
66
35
33
66
35
5
19
14
18
30
57
Step 4 Assembly List
2 ADJ PULLEY PLATE 1/8 X 2 X 9 2
11 LAT CABLE 1
12 LOW ROW CABLE 1
21 NYLON PULLEY 3/8 X 1 1/2 X 4 1/2 2
22 NYLON PULLEY 3/8 X 1 X 4 1/2 5
31 FINISHED HEX NUT 1/2-13 1
33 FLAT WASHER SAE 3/8” 14
36 HEX HEAD CAP SCREW 3/8-16 X 1 3/4 4
37 HEX HEAD CAP SCREW 3/8-16 X 2 3/8 1
39 HEX HEAD CAP SCREW 3/8-16 X 4 1/2 2
44 LAT BAR 48” 1
47 NYLON INSERT JAM LOCK NUT 3/8-16 7
48 NYLON INSERT LOCK NUT 5/16-18 2
58 RUBBER GRIP 1 X 6 1/4 2
60 SHOULDER BOLT 3/8 X 3/4 2
61 SNAP LINK 8MM X 80MM 3
63 SOCKET SET SCREW 3/8-16 X 3/4 3
64 SPLIT BOLT 1/2-13 X 1 1
65 SPLIT HEX TAP BOLT 1/2-13 X 3 1/2 1
67 SPLIT WASHER 1/2” 2
68 STRAP BRACKET 20 #SF20 2
3
33
66
57
Item # Description Qty.
33
66
35
4 RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
48
58
44
47
3347
47
33
33
22
36
33
36
22
33
36
47
2
33
21
37
33
22
36
68
61
FIG. A
46
60
14
FIG. C
63
FIG. B
64
67
11
19
39
65
31
67
12
5
11
33
39 33
21
22
33 47
33 47
5RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
RLM-855WS Exploded View Diagram
35
66
47
33
33
10
23
21
50
34
6
24
66
20
34
34
33
66
35
20
47
33
33
37
66
53
24
22
66
33
33
33 36
33
66
35
38
47
33
38
47
47
16
33
33
14
53
22
2
33
33
36
38
66
33
8
22
36
8
19
18
35
66
33
53
21
17
39
6
33
13
51
34
33
9
55
35
33
47
59
63 3
4
38
54
56
38
38
33
17
33
33
22
35
66
33
54
39
47
33
33
52
33
66
33
47
33
35
5
33
38
35
66
33
22
33
47
2
66
33
47
30
33
36
49
52
57
26
15
1
49
33
57
40
32
69
59
59
7
51
6 RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
COLOR CHART
BOLD FONT = SUB-ASSEMBLY PARTS
BLACK= HARDWARE
RLM-855WS
Parts List
REV0
ITEM DESCRIPTION REV PART NO. QTY ITEM DESCRIPTION PART NO. QTY
1 REINFORCEMENT PLATE 1/4 X 2 X 7 (BEND) 0 UP3720 1
2 ADJ PULLEY PLATE 1/8 X 2 X 9 0 UP0092 2
3 BASE FRAME 0 UP3915 1
4 BENCH FRAME 0 UP3916 1
5 CENTER POST 0 UP3917 1
6 FOAM FOOT ROLL 1 X 4 X 7 W/VINYL 0 UP3785 2
7 FOOT ROLL TUBE 1 X 16 0 UP0053 1
8 GUIDE ROD 3/4 X 73 1/8 0 UP3918 2
9 HOLD DOWN T BAR 0 UP3919 1
10 LAT BAR HOLDER 0 UP3744 1
11 LAT CABLE 0 UP3920 1
12 LOW ROW CABLE 0 UP3921 1
13 LOW ROW FOOT SUPPORT 0 UP3922 1
14 SELECTOR PIN W/COIL 3/8 X 4 0 UP3035 1
15 STABILIZER 0 UP3924 1
16 TOP ASSEMBLY 0 UP3925 1
17 UPH PAD 0 UP3914 2
18 10 LB STEEL WEIGHT PLATE BLACK 4 9/16 X 9 7/16 BNH1650 19 53 PLASTIC INSERT CAP ELLIPTICAL 2 X 4 BNH1794 3
19 10 LB TOP PLATE W/22" SLTR BAR 19 BLK WTS BNH2020 1 54 PLASTIC STOPPER 1 ID X 1 3/8 OD X 1 BNH2053 2
20 ALUMINUM WASHER .390 ID X 1.500 OD X .150 THK BNH1541 2 55 PLASTIC TUBE GUIDE W/LIP 2" SQ BNH0058 1
21 BLACK NYLON PULLEY 3/8 X 1 1/2 X 4 1/2 (V3700) BNH1694 2 56 PULL PIN 1/2 X 2 3/4 SHORT NOSE (YELLOW) BNH0640 1
22 BLACK NYLON PULLEY 3/8 X 1 X 4 1/2 BNH0506 5 57 RUBBER DONUT 3/4 X 2 1/2 BNH0068 2
23 BLACK RUBBER GRIP 1/2 X 4 7/8 BNH1818 2 58 RUBBER GRIP 1 X 6 1/4 BNH0296 4
24 BUTTON HEAD SOCKET CAP SCREW Z/P 3/8-16 X 1 BNH2033 2 59 SAFETY TAPE ANTI-SLIP 4 9/16 X 7 1/4 BNH2054 4
25 COIL CHAIN Z/P 3/16" X 12 BNH2055 1 60 SHOULDER BOLT ALLOY 3/8 X 3/4 BNH0718 2
26 DECAL-ADJUST CABLE HERE BNH1751 2 61 SNAP LINK Z/P 8MM X 80MM BNH0065 3
27 DECAL-CAUTION WEIGHT TRAINING SAFETY... BNH0126 1 62 SOCKET SET SCREW ALLOY 10-32 X 1/8 BNH0473 1
28 DECAL-DANGER TIGHTEN THIS RET..., 3/4 X 1-1/2 BNH0142 1 63 SOCKET SET SCREW ALLOY 3/8-16 X 3/4 BNH0476 3
29 DECAL-FOR BEST PERFORMANCE 1 1/4 X 1 1/2 BNH0143 1 64 SPLIT BOLT Z/P 1/2-13 X 1 BNH0479 1
30 DECAL-WEIGHT NUMBERS REF TP-10 (200 lbs) BNH1542 1 65 SPLIT HEX TAP BOLT GR-5 B/O 1/2-13 X 3 1/2 BNH1131 1
31 FINISHED HEX NUT B/O 1/2-13 BNH0201 1 66 SPLIT LOCK WASHER Z/P 3/8" BNH2032 13
32 FLAT PHILLIPS SCREW ZINC # 2 X 1/2 BNH1480 2 67 SPLIT WASHER Z/P 1/2" BNH0572 2
33 FLAT WASHER SAE Z/P 3/8" BNH2030 37 68 STRAP BRACKET 20 #SF20 BNH0562 2
34 FOAM ROLL 1" NYLINER BUSHING BNH2025 4 69 TUFFSTUFF LOGO ALUMINUM SMALL BNH1323 1
35 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 1 BNH2037 9 70 LOW ROW BAR 20" BNH0294 1
36 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 1 3/4 BNH2040 4
37 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 2 3/8 BNH2043 1
38 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 2 3/4 BNH2045 8
39 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 4 1/2 BNH2052 2
40 HEX HEAD CAP SCREW GR-5 Z/P 3/8-16 X 5 BNH2051 2
41 HEX KEY 3/16" BNH0371 1
42 HEX KEY ALLOY 3/32" BNH0373 1
43 HEX KEY ALLOY 7/32" BNH0575 1
44 LAT BAR 48" BNH0295 1
45 LITHIUM GREASE SMALL CONTAINER BNH0705 1
46 NYLON BALL W/THREADED SOCKET 1 3/4 X 5/16 BNH0022 2
47 NYLON INSERT JAM LOCK NUT Z/P 3/8-16 BNH2026 11
48 NYLON INSERT LOCK NUT Z/P 5/16-18 BNH2056 2
49 PLASTIC HORIZONTAL ELLIPTICAL SHOE BNH1847 2
50 PLASTIC INSERT CAP 1 3/4" SQ 10-14 GA BNH0053 1
51 PLASTIC INSERT CAP 1" RD 10-12 GA BNH0002 2
52 PLASTIC INSERT CAP 1" X 3" _ 11 GA. BNH0007 2
7RLM-855WS Lat Machine W/200 Lbs Steel Weight Stack
DO NOT DISCARD THIS MANUAL
HOME LIFETIME WARRANTY
TuffStuff products are warranted to the retail purchaser to be free from defects in materials and workmanship.
TuffStuff exclusive Home Lifetime Warranty coverage extends for the life of the product while owned by the
original retail purchaser, and used only in a home or residential setting unless otherwise noted in the owner’s
manual.
This warranty does not cover:
1. TuffStuff products sold for and used in a commercial or institutional setting.
2. Any damage, failure or loss caused by accident, misuse, neglect, abuse, improper assembly, improper
maintenance, or failure to follow instructions or warnings in the owner’s manual and warning labels
posted on the machine.
3. Use of products in a manner for which they were not designed.
4. Original product that is altered, or the use of replacement parts and components of another manufacturer other than TuffStuff.
Limitations:
The foregoing shall constitute the sole remedy of the purchaser and the sole liability of TuffStuff with regard to
warranty, whether express or implied by operation of law or otherwise, including but not limited to any implied
warranties of merchantability or fitness. TuffStuff shall in no event be liable for incidental or consequential
losses, damages or expenses in connection with exercise products. TuffStuff’s liability hereunder is expressly
limited to the repairs or replacements of warranted defective parts.
Procedures:
Warranty service will be performed at TuffStuff’s facility in Pomona, California. TuffStuff will have the option of
either repair or replacement at no charge for any defective product. Purchaser is responsible for installation of
repaired or replaced parts and all transportation and insurance costs on returned or replaced equipment to and
from TuffStuff’s facility in Pomona.
This warranty gives you specific legal rights and you may also have other rights, which may vary from state to
state. Effective July 1, 2004.
This warranty is the final, complete and exclusive agreement of the parties with respect to the quality or performance of the equipment
and no action for breach of this written warranty or any implied warranty shall be commenced more than one (1) year after the accrual
of the cause of action. No modification of this warranty or waiver of its terms shall be binding on either party unless approved in
writing by an authorized representative of the party. Contact TuffStuff at 1325 E. Franklin Avenue, Pomona, California 91766, before
returning any defective equipment.
Note: Retain your sales receipt and be sure to mail in the warranty registration card to insure that a
permanent record of your purchase is on file with the factory and to avoid unnecessary delays in
warranty service.
TuffStuff Fitness Equipment, Inc.
1325 E. Franklin Avenue
Pomona, CA 91766, USA
Ph: 909-629-1600 Fax: 909-629-4967
E-mail: service@tuffstuff.net Net: www.tuffstuff.net
Loading...