Chicken Coop
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
Step by Step Assembly Instruction
Finished Size:2*3*2m
Step 1 Check parts before assembly.
(1815mm)
B Tube
(1420mm)
C Tube
(1420mm)
(940mm)
( )
515(1 mm)
515(1 mm)
(1670mm)
D Tube
E Tube
F Tube
2
2
4
2
2
G Tube
H Tube
A Tube
5
cs
cs
cs
cs
cs
cs
2
1
cs
cs
L connection
M connection
N connection
connection
P
0
cs
4
cs
6
cs
0
cs
(430mm)
(570mm)
J Tube
K Tube
cs
1
cs
1
Hexagonal wire mesh
2
rolls
Carriage Bolts with nuts
6
pcs
Clip spring 35pcs
I Tube
1
cs
Carriage Bolts with nuts
4
pcs
Clamps
1
cs
12
A bundle of cable ties
A tarp
Bungee Ball 20 pcs
Please note before assembly: put each clip spring into each tube with narrowed ends as below:
Please note before assembly: put each clip spring into each tube with narrowed ends as below:
Step 2 Assemble coop on a level surface and connect the bottom frame.
Gather2 A-tubes, B-tubes, and
2
C-tubes,2
4
M-connections.
(1815mm)
(1420mm)
(1420mm)
Slip ends of tubing into the connections.
(1420mm)
(1420mm)
(1815mm)
Step 3 Add uprights.
Gather: 4 D-tubes, and put them into the connections.
(940mm)
2
Step 4 Add connections.
Gather:
4 N -connections
and put
into the D-tubes.
them
Step 5 Add A-tubes.
Gather: 2 A-tubes. And put them into the connections.
(1892mm)
Step 6 Add roof frame.
Gather: ,
2 E -tubes,2 F -tubes
into the connections.
(1515mm)
and 2 N -connections.
Put the ends of
the tube
3
Step 7 Add top tubes.
Gather: A-tubes. And put them into the connections.
1
(1815mm)
4
Step 8 Add gate post.
Gather: 2 G-tubes.
And put the narrow side of G-tubes into F-tubes.
(1670mm)
clamps
4 , 2 carriage bolts with nuts.
clamps
Connect the G-tubes and B-tubes with 2
4
and
carriage bolts with
nuts.
5
Step 9 Add K-tube.
Gather: 1 K-tube, 4 , 2 carriage bolts with nuts.
Connect the K-tube and F-tube with
clamps
, .
carriage bolts with nuts.
2
and
(570mm)
clamps
4
.
6
Step 10 Assemble the gate frame.
Gather: 1 H-tube, 1 I -tube, 4
Connect the tubes, with
(430mm)
4
clamps
1 J-tube,
and
clamps
carriage bolts with nuts.
2
, 2 carriage bolts with nuts.
.
.
Step 11 Install the gate.
1. Gather male and female hinges, 4 carriage bolts with nuts, and the gate.
2. Install the upper and lower female hinge.
3. Position the gate centered in the gate opening.
4. Attach bottom male hinge and slide up to meet bottom female hinge. Tighten
securely .
5. Attach top male hinge and slide down to meet top female hinge. Tighten securely .
6. With an adjustable wrench, install the gate latch.
7
Step 12 Add wire mesh
1. Tie the ire mesh and the tube at the
start
of part 1
with
And drape long side of wire
2. Repeat above step to cover part 2 to 6.
3. Tie the tubes and wire mesh together
for all the coop frame.
2
the
Gather 2 roll wire mesh and
w
cable ties is advised to be 20cm, same with next steps.)
cable ties.
cable ties.(The space between
mesh over the frame. Tie the wire mesh and the tube of other end of part 1. Cut the
extra mesh.
8
Step 13 Add Tarp and Secure with Ball Bungees
Gather tarp and 20 ball bungees. Drape
sides of tarp over frame. Attach all
four
bungees to the tarp and coop frame.
Important: Tarp is not designed to withstand the weight of snow.
9
Loading...