Tucker GTR6 SS, GTR6 S, GTR5 SS, GTR5 S, GTR5 User Manual

ASSEMBLY AND INSTALLATION INSTRUCTIONS

GTR BARBECUE INSULATION JACKET

MODELS:

GTR3, GTR4, GTR5, GTR6.

GTR3 SS, GTR4 SS, GTR5 SS, GTR6 SS.

GTR3 S, GTR4 S, GTR5 S, GTR6 S.

IMPORTANT – PLEASE READ ALL INSTRUCTIONS
BEFORE YOU ASSEMBLE, INSTALL OR
OPERATE THIS APPLIANCE.

CONTENTS

GENERAL WARNINGS

INSULATION JACKET
ASSEMBLY INSTRUCTIONS

INSTALLATION INSTRUCTIONS
& WARNINGS

DIMENSIONS

3

4

8

10

2

IMPORTANT SAFETY
INSTRUCTIONS

• Tucker GTR Barbecues are approved for
outdoor use only.

• Remove all plastic protection lm from
stainless steel components before assembly.

• Keep this manual for future reference.

• Read all instructions carefully before
assembly and usage of barbecue.

• Clean your barbecue regularly; check the
grease trays for excess grease build up as

damage by grease or fat re is not covered

by warranty.

• Always turn off the gas supply when you

nish barbecuing.

• A canvas cover for this barbecue will extend
its life and ensure trouble free operation.

• For installation of this barbecue onto its

cabinet refer to relevant instructions.

• Attend an operating barbecue at all times.

• Do not use this appliance indoors or in any
enclosed area.

• Read all instructions carefully before
assembly and usage of the barbecue.

• Do not use or store ammable materials in or
near this appliance.

• Always leak test /check hose connections

after lling cylinders.

• Check cylinder condition for rust and that
the date stamp is current as every gas
cylinder in Australia must be pressure tested
every ten years.

• Never disconnect the barbecue whilst it is
running.

• Do not modify this appliance in any way.

• Do not allow children to operate the
barbecue.

• If a grease/fat re should arise, turn off the
gas supply immediately until extinguished.

• Always open the Lid or Roasting Hood before
lighting.

• Do not spray aerosols in the vicinity of this
appliance while it is in operation.

• Do not place articles on or against this
appliance.

WARNING FOR

YOUR SAFETY

If you smell gas:

1. Shut off gas supply to appliance.

2. Extinguish any open ame.

3. Open lid or hood.

4. If odour continues, immediately call your
gas supplier or your Fire Department.

HAZARDOUS FIRE OR EXPLOSION MAY
RESULT IF INSTRUCTIONS ARE IGNORED.

It is the consumer’s responsibility to see that the
barbecue is properly assembled, installed and
taken care of. Failure to follow the instructions in
this manual could result in serious bodily injury
and /or property damage.

3

INSULATION JACKET
ASSEMBLY

JACKET ASSEMBLY

Tools required for assembly – Phillips head
screwdriver and shifting spanner.

• Unpack and check that you have all
components before building the Insulation
Jacket.

INSULATION JACKET PARTS LIST

• Left side panel and insulation wool.

• Right side panel and insulation wool.

• Base panel and insulation wool.

• Small hose cover panel and 2 x nuts and

bolts.

• Rear Back Panel and insulation wool.

• BBQ Front angle panel.

• Drip tray fascia panel.

• Packet of nuts and bolts.

1. Attach left and right hand side panels to the
base panel with the 6 bolts as per photo.

We recommend you remove the insulation

wool from the panels for this process and

have the side panels at and the base panel

vertical so that the bolts drop down into the
holes to make it easier to bolt the panels
together.

Do not tighten the bolts up.

2. Now attach the front drip tray fascia panel
to the front of the jacket, the front fascia
panel has a pin on either side of it, that
locates into the holes on either side of the
side panels.

The pins allow the drip tray fascia panel to

fold up and down.

2.1. Insert spacer into the pin.

4