T Therm Geo TST-***, TST-024, TST-036, TST-048, TST-060 Installation & Operating Instructions Manual

Two-Stage Split Geothermal Heat Pump

Installation & Operating Instructions

Model: (TST-***)

Application

 Retrofit existing forced air installations
 Dual Heat – combine this geothermal unit and A-coil with standby

gas or oil furnace

 LMC (Load management control), LMC/INT ready
 Tested to UL Standards 1995

Information

The air coil furnished with this product has been tested and certified
with this unit. To maintain the specification performance and product

certification, the air coil shipped with this unit must be used.

This unit may not be tax credit eligible when a coil other than the
furnished coil is used.

For optimum performance an ECM blower is recommended. The CFM airflow required in the
specification table must be matched to the compressor stage by the installed furnace blower/air handler.

Since this product requires line sets and air coil installation, an experienced and licensed refrigeration
technician is required.

Domestic Water Heater, Desuperheater

Energy Star promotes the desuperheater and it is offered as an optional item for all TTHERM GEO™
heat pumps. Our exclusive GEO Logic™ control system optimizes the operation of a desuperheater,
operating the systems only when there is adequate energy available to provide heat to the domestic hot
water. However, to maximize the times the desuperheater aides in providing domestic hot water, a hot
water preheat tank is suggested, see Desuperheater section of this manual.

Note – The GEO Logic control board has various required setup adjustments, see Field Setup section.

DO NOT DESTROY THIS MANUAL. PLEASE READ CAREFULLY AND KEEP IN A

SAFE PLACE FOR FUTURE REFERENCE BY A SERVICE TECHNICIAN.

Important information

Model Number:____________________________
Serial Number:_____________________________
Installing Contractor:________________________

12/03/2012 GI301

Table of Contents

Introduction 1

Product Configurator (GC002) 3

Mechanical Specifications 4

Electrical Data 5

Product Dimensions 6

Installation Requirements 7

Mechanical Installation Overview 8

Mechanical Installation Source Water 11

Desuperheater, Domestic Hot Water 16

Duct System/A-Coil Installation 18

Installing the TXV 19

Mechanical Installation Refrigeration 22

Charging Procedure 23

Superheat and Sub-Cooling 24

Unit Operating Conditions Heat & Cool 25

R-410A Pressure/Temperature Conversion Chart 27

Electrical Hookup 28

GEO Logic Controller 29

Accessories/Options 30

Field Setup Overview 32

Duel Fuel/Utility Control 32

Operation Indicators 34

Power On, Start Up 38

Operational Tips 40

Troubleshooting 41

Preventative Maintenance 44

Drawing GH001 – TT-INT-1 Hookup 46

Drawing GR301 – Refrigerant Hookup 47

Drawing UAW555 – Electrical Diagram 49

Warranty Information – GX002 50

12/03/2012 GI301

Introduction

Geothermal heat pumps are able to heat and cool spaces with efficiencies exceeding 350% by taking advantage
of solar heat stored in the earth’s crust and the earth’s relatively stable temperatures. In the winter time, heat is
moved from the earth into the home and concentrated using a refrigeration system. Since the heat already exists
in the soil, the cost of operation of the geothermal heat pump is, in effect transportation cost for the free heat. In
the summer, heat is removed from the home by reversing the refrigeration process and sending heat back out
into the earth. A geothermal system consists of an earth source (either open loop or earth loop heat exchanger),
a geothermal heat pump containing the refrigeration system and a ductwork system for delivering the
conditioned air to the individual rooms. To learn more about geothermal heating, please visit our web site at
www.tthermgeo.com

This is a pre-wired package for converting a new or existing oil or gas furnace into a dual heat system. This is a
complete package for both heating and air conditioning, utility load control, and compatible with DC drive
variable speed furnaces. The GEO Logic control uses a standard, multi-wire heat pump room thermostat to
initiate and terminate all heat/cool functions. There are various temperature sensors, pressure sensors, water
flow switch, etc. which continuously monitor the heat pump system. The interaction of these sensing
components, room thermostat requests, and the various heat pump refrigeration components are all controlled by
an integrated microprocessor system (GEO Logic). The various setup conditions for this microprocessor based
controller determine the application and geo product series. These setups are initially programmed by the
factory, but special PC software and cable are available for reprogramming as required for controller
replacement and/or other options which may apply to the specific installation. See Additional Equipment
Concerns, Field Setup or Programming, Operation Indicators, User Instructions, Control Sequence, and
Troubleshooting sections within this manual for further details on the GEO Logic control.

The utility load control receiver interfaces with the T2-TT-INT-1 which properly switches the heating mode and
properly controls the air conditioning mode during summer load interrupt. The blower circuit and control is also
designed for heating interrupt (blower handled by gas furnace only) and continuous operating blower during
cooling peak load interrupt. Typically these controls and design features are only found in this product.

Moving and Storage

Units should be stored in original packaging in a clean dry area. Store and move units in normal upright
position. Do not stack units. Transport in vertical position only.

Initial Inspection

Be certain to inspect all cartons and crates as units are received before signing the freight bill. Verify that all
items received have no physical damage. Report any damages or shortages on the freight bill. The purchaser is
responsible for filing the necessary claims with the carrier. Concealed or hidden damages not discovered until
removing packaging must be reported to the carrier within 15 days of receipt.

Unit Location and Mounting

Locate the unit in an indoor area where the ambient temperature will remain above 45°F [8°C]. TTHERM GEO
Heat Pump provides 4 removable panels for ease of servicing.. This unit is zero clearance rated; however, allow
enough room to remove panels for service and maintenance. Suggest setting unit on a sound vibration pad, see
accessories price sheet, part # E2-0122. Water supply should not be hard plumbed directly with copper or PVC
pipe as this could transfer any vibration to living space. Consider using Hose Kit part # L3-0015B to minimize
transferred vibration.

Please read and understand conditions associated with proper installation, unauthorized changes, and POWER ON
procedures.

Warranty Statement

See the last page of this manual for detailed limited warranty coverage explanation.

12/03/2012 1 GI301

WARNING

BEFORE PERFORMING SERVICE OR MAINTENANCE OPERATIONS ON A SYSTEM, TURN OFF
MAIN POWER SWITCHES TO THE INDOOR UNIT. IF APPLICABLE, TURN OFF THE ACCESSORY
HEATER POWER SWITCH. ELECTRICAL SHOCK COULD CAUSE PERSONAL INJURY.

Installing and servicing heating and air conditioning equipment can be hazardous due to system pressure and
electrical components. Only trained and qualified service personnel should install, repair or service heating and
air conditioning equipment. Untrained personnel can perform the basic maintenance functions of cleaning coils
and cleaning and replacing filters. All other operations should be performed by trained service personnel.
When working on heating and air conditioning equipment, observe precautions in the literature, tags and labels
attached to the unit and other safety precautions that may apply, such as the following safety measures:

 Follow all safety codes.
 Wear safety glasses and work gloves.
 Use a quenching cloth for brazing operations.
 Have a fire extinguisher available for all brazing operations.

Warnings, Cautions, and Notes

Throughout this manual there are warnings, cautions and notes containing various levels of important
information. Read all of these items carefully before performing any installation, servicing or troubleshooting
of the system.

Warnings are for any item which MUST be followed and failure to do so could result in serious injury or even

death and/or serious damage to the equipment.

Cautions relate to potentially hazardous situations or important practices which if ignored could cause minor to
moderate injury or cause equipment damage or performance problems.

Notes are used to indicate items of high importance but are not related to a hazardous situation.

Safety Considerations

12/03/2012 2 GI301

T V T - 0 4 8 - 1 C L D X 1 - X X

1 2 3 4 5 6 7 8 9 10 11 12 13 14

TTHERM GEO (1)

Unit Style (2)

C = Combo

H = Hydronic

S = Split

V = Vertical

Unit Type (3)

A = Single Stage

T = Two Stage

Nominal Tonnage (4, 5, 6)

Voltage Option (7)

Heat Exchanger Option (8)

M = Copper (Load) & Cupronickel

S = Stainless (THT only)

024 = 2-ton
036 = 3-ton

042 = 3.5-ton

048 = 4-ton
060 = 5-ton
072 = 6-ton

096 = 8-ton
120 = 10-ton
144 = 12-ton

1 = 208/230V, 1 Ph
2 = 208/230V, 3 Ph
3 = 460/480V, 3 Ph

C = Copper

N = Cupronickel

(Source)

TTHERM GEO Heat Pump Configurator

Model Number Digits

TVT-048-1CLDX1-XX

Auxiliary kW Option* (13, 14)

05 = 4.8 kW
10 = 9.6 kW
15 = 14.4 kW
20 = 19.2 kW
XX = None

*Can be factory or field installed

Vintage (12)

1

Miscellaneous Kits (11)

A = Soft Start Kit (Installed)
X = None

Desuperheater Option (10)

D = Desuperheater w/Factory

Installed Pump

X = None

Configuration Option (9)

L = Left Return (Standard)*
R = Right Return
C = Split Air Coil
X = N/A or No Split Air Coil

*Left return can be field converted to right return

10/12/2012 GC002

Mechanical Specifications – R410A Two-Stage Compressor

MODEL

TST-024

(2 ton)
Coax & Piping Water Volume – gal .43 .65 1.1 1.1
Source Temperature °F (min/max) 20°/120° 20°/120° 20°/120° 20°/120°
Nominal source differential* ° F (H/C) 3/12° 9/11° 6/11° 6/10°
Factory Charge R410A 3 lbs. 10 oz. 6 lbs. 1 oz. 7 lbs. 2 oz. 7 lbs. 2 oz.
Static Pressure – Nominal 0.3 0.3 0.3 0.3
Static Pressure – Design 0.5 0.5 0.5 0.5
Weight– Base Unit Only (lbs) 240 275 320 320

Model GPM PSID Model GPM PSID Model GPM PSID Model GPM PSID

4 1.2 6 1.8 8 1.3 10 1.9

2-ton

6 2.7 9 2.4 12 2.5 15 3.6
8 3.6 12 4.3 16 4.0 20 5.8

10 5.6

HEAT EXCHANGER PRESSURE DROP TABLE

Water-to-Air (Source Side, Pure Water @ 68° F)

3-ton

15 6.7

PRESSURE DROP MULTIPLIERS

Freeze Point (° F) 20° F 25° F 30° F 35° F 40° F

Pure Water Multiplier 32 1.00 1.00 1.00 1.00 1.00
Methanol 12.5%* Multiplier 16.2 − 1.25 1.21 1.18 1.15
Propylene Glycol 20%* Multiplier 18.4 1.39 1.35 1.31 1.28 1.24
Ethanol 20%* Multiplier 18.1 1.56 1.47 1.42 1.36 1.31

1. Capacities are based on temperatures shown in heading, source is left group, return air is right group.

2. Stated Btu/h is the ISO 13256-1 formula adjusted, actual HP supply energy delivered is 2% greater.

3. Temp rise is based on sensible only.

4. All ratings based upon operation at lower voltage of dual voltage rated models.

5. Ground Loop Heat Pump ratings based on 15% antifreeze solution.

*By volume Feet of Head = PSI x 2.31

HEATING – ISO 13256-1 SPECIFICATION – ENERGY STAR

Model Stage

TST-024

TST-036

TST-048

TST-060

FL 8 32.9 850 32 4.05 24.8 850 26 3.56
PL 8 21.8 725 29 21.6 18.5 725 26 3.89
FL 10 42.3 1200 31.8 4.01 33.0 1200 26.5 3.62
PL 10 30.1 1000 27.4 4.35 26.9 1000 24.0 3.90
FL 12 56.0 1500 37 4.02 47.7 1500 29 3.57
PL 12 38.5 1200 31 4.33 37.7 1200 29 3.98
FL 15 70.7 1875 36 4.10 55.7 1875 28 3.59
PL 15 51.9 1480 32 4.22 46.3 1480 30 3.86

Source

GPM

COOLING – ISO 13256-1 SPECIFICATION – ENERGY STAR

Model Stage

TST-024

TST-036

TST-048

TST-060

FL 8 32.8 950 22 19.4 30.6 950 20 16.3
PL 8 23.3 825 21 23.8 22.5 825 22 20.9
FL 10 45.1 1250 20.7 19.7 44.1 1250 19.4 15.8
PL 10 32.2 1050 19.4 22.5 30.5 1050 18.2 18.9
FL 12 63.8 1600 22 19.7 57.4 1600 23 15.4
PL 12 46.9 1275 24 23.5 45.1 1275 23 20.8
FL 15 70.2 2000 23 19.2 63.3 2000 23 14.7
PL 15 50.4 1650 21 23.0 51.3 1650 22 19.7

Source

GPM

GWHP – Ground Water GLHP – Ground Loop
50° F 68° F 32° F/41° F 68° F

Capacity

Btu/h

Blower

CFM

GWHP – Ground Water GLHP – Ground Loop
59° F 80.6° F 77° F/68° F 80.6° F

Capacity

Btu/h

Blower

CFM

4-ton

Temp

Rise

Temp

Drop

TST-036

(3 ton)

20 5.8

COP

EER

Capacity

Btu/h

Capacity

Btu/h

TST-048

(4 ton)

5-ton

Blower

CFM

Blower

CFM

TST-060

(5 ton)

25 8.5

Temp

Rise

Temp

Drop

COP

EER

12/03/2012 4 GI301

Electrical Data – Single Phase

Desup.

Pump

Model

Voltage Compressor

(60 Hz) RLA LRA FLA FLA FLA Ampac.

TST-024 208/230-1 13.1 73.0 .15 4.4 17.7 20.9 40
TST-036 208/230-1 17.9 96 .15 4.4 22.5 26.9 50
TST-048 208/230-1 27.1 152.9 .15 4.4 31.6 38.2 60
TST-060 208/230-1 29.7 179.2 .15 4.4 34.3 41.7 70

Loop

Pump

(Ext)

Total Min.

Max.
Fuse/

HACR

Electrical Data – Three-Phase

Desup.

Pump

Model

Voltage Compressor

(60 Hz) RLA LRA FLA FLA FLA Ampac.

TST-024 Not Available

TST-036 200/230-3 14.2 88 .15 4.4 18.6 22.1 30
TST-048 200/230-3 16.5 110.0 .15 4.4 20.9 25.0 40

TST-060 Not Available

Loop

Pump

(Ext)

Total Min.

Max.
Fuse/

HACR

TST Blower CFM Requirements

Model

G Y *Y2

Heat / Cool Heat / Cool
TST-024 Furnace Default 725 / 825 850 / 950
TST-036 Furnace Default 1000 / 1050 1200 / 1250
TST-048 Furnace Default 1200 / 1275 1500 / 1600
TST-060 Furnace Default 1450 / 1650 1875 / 2000

* When the TST unit is installed with a single speed furnace blower, the blower needs to be capable of

delivering the CFM required by Y2

12/03/2012 5 GI301

Product Dimensions

Forced Air Coil – Reference Information

12/03/2012 6 GI301

Installation Requirements

1. All installation work must be performed by trained, qualified contractors or technicians. TTHERM GEO

Heat Pump, sponsors installation and service schools to assist the installer. Contact TTHERM GEO at

[e-mail]

WARNING

ALL ELECTRICAL WIRING MUST BE IN ACCORDANCE WITH NATIONAL ELECTRIC CODE
AND LOCAL ELECTRIC CODES, ORDINANCES, AND REGULATIONS.

WARNING

OBSERVE ELECTRIC POLARITY AND WIRING COLORS. FAILURE TO OBSERVE COULD
CAUSE ELECTRIC SHOCK AND/OR DAMAGE TO THE EQUIPMENT.

CAUTION

This unit can only be used for its intended design as described in this manual. Any internal
wiring changes, modifications to the circuit board, modifications or bypass of any controls, or
installation practices not according to the details of this manual will void the product warranty,
the safety certification label, and manufacturer product liability. TTHERM GEO, cannot be
held responsible for field modifications, incorrect installations, and conditions which may
bypass or compromise the built-in safety features and controls.

2. If this is a Dual Heat system, this product relates only to the addition to the furnace ducting system external

to the gas or oil force air furnace. The owner/installer assumes all responsibility and/or liability associated
with any needed installation of the gas/oil furnace, fuel system, flue, chimney, etc. Any instructions or
comments made within this manual (or factory phone assistance) relating to the gas/oil furnace are provided
as comments of assistance and “helps” only.

for upcoming dealer training events.

CAUTION

This unit shall not be operated (either heating section or blower) until the interior of the
structure is completed and cleaned. This also means all duct work must be complete with filter,
etc. Manufacturer’s warranty is void if this unit is operated during structure construction.

CAUTION

Hazards or unsafe practices could result in property damage, product damage, severe personal
injury and/or death.

3. All removed or discharged refrigerant must be recovered. Local and federal statutes are to be observed.

Should a compressor need replacing, the compressor oil is to remain with the compressor. Refrigerant lines
on the compressor must be sealed.

4. Remember, safety is the installer’s responsibility and the installer must know this product well enough to

instruct the end user on its safe use.

At TTHERM GEO, the safety of the installer and the end user is of highest priority. Remember, safety is
the installer’s responsibility and the installer must know this product well enough to instruct the end user on
its safe use. Professional installers should be trained and experienced in the areas of handling electrical
components, sheet metal products, and material handling processes.

12/03/2012 7 GI301

Mechanical Installation Overview

This TTHERM GEO series unit cannot correct airflow problems inherent within the duct work system. The
following items should be carefully considered and properly followed for all installations:

Examination of the existing forced air furnace – Prior to starting this installation or furnace modification,

examine the total furnace system and make necessary comments or recommendations to the homeowner.
Remember, if a marginal condition exists within the existing forced air system, the installation of a geothermal
heat pump will not cure PRE-EXISTING conditions. Consider such items as proper fossil fuel ignition, is the
furnace cycling on hi-limit, filter, adequate cold air return, adequate supply duct and room register. Inspect and
count supply and return registers for size and number.

Heating capacity – Size the geothermal heat pump according to the normal heating requirements as the building

exists today
geothermal heat pump should be sized to the heat loss of the house. Heat loss and heat gain audits should be
done to determine proper equipment sizing.

Supply plenum – Carefully examine all sides of the plenum. Installing the coil in the supply plenum of a fossil

fuel furnace is the preferred location. If the coil is installed in the return ductwork, the cool air during cooling
could be detrimental to the life of the furnace. Either location would be fine in the case of a fan coil. Verify all
transitions have angles less than 30, the coil is centered within the plenum/ductwork, and there are no odd
shaped angles or odd shaped transitions within the plenum/ductwork.

Other plenum equipment – Auxiliary equipment such as humidifiers, zone plenum dampers, etc., located

within the plenum which may cause a non-uniform airflow issues may have to be removed if they cause to great
reduction to system airflow.

Insufficient cold air return capacity – Installation experience indicates this is a major concern. In fact, it

could represent a problem in as many as 60% of the installations, especially if there is a requirement to increase
airflow with the existing blower and the existing cold air return capacity is already undersized or restricted.
Check the static pressure within the return cabinet or the suction at the filter cabinet door. Do not assume
because there is a register on the wall, the hole behind the register or the passageways are equal to this register.
Sharp offsets and transitions in the cold air return system often cause severe restrictions. Expect to add
additional registers or a relief register in the main cold air return duct. Best practice would include both high and
low return registers.

Blower CFM capacity – The furnace forced air system must have an airflow capacity larger than the minimum
requirement on the TTHERM GEO Series specification sheet (see unit nameplate and/or Mechanical
Specifications). It is near impossible to correctly measure CFM airflow in an existing residential installation.

Experience and rule of thumb indicators will have to be followed to determine the existing furnace CFM
capacity. The following may be helpful:

. Do not necessarily match to the existing furnace nameplate because it may be oversized. The

Comment – zone dampers cause back pressure on the blower and overall reduced airflow. Reduced
airflow can cause the geothermal unit to perform poorly or in some cases cause icing or freeze ups in the
air coil. If the smallest zone cannot handle the minimum CFM requirements of the heat pump, create a
dump zone and/or allow air flow to bypass to other zones.

a. Existing furnace nameplate

the systems static pressure. What changes have been made to the heating system since
installation?

b. Blower motor size

- Used only as a minimal guide.

2 ton unit - 1/3 HP or larger
3 ton unit - 1/2 HP or larger
4 ton unit - 3/4 HP or larger
5 ton unit - 1 HP or larger

c. Observe/examine airflow ducting system and design

- Typically represents a high or optimistic rating and is a function of

- Use duct sizing table , or industry

12/03/2012 8 GI301

equivalent duct capacity airflow charts and determine if the system is capable of delivering the
CFM required on the nameplate. Especially check the number of registers and the number of “6
inch rounds”. The same would apply to cold air return duct capacity.

d. Calculated CFM

- By measuring the temperature rise across the existing furnace, the CFM can
be approximated. The accuracy of this formula will depend upon the estimated or determined
Btu output (actual heat energy across the furnace, not nameplate input).

CFM =

Btuh (output)

Temperature Rise x 1.08

Duct Sizing Chart
Acceptable Branch Duct Sizes Acceptable Main or Trunk Duct Sizes
CFM ROUND Rectangular Round Rectangular

100 6” 4x8, 4x6
150 7” 4x10, 5x8, 6x6
200 8” 5x10, 6/8,4x14,7x7
250 9” 6x10, 8x8, 4x16
300 10” 6x14, 8x10, 7x12
350 10” 6x20, 6x16. 9x10
400 12” 6x18, 10x10, 9x12 10” 4x20, 7x10, 6x12, 8x9
450 12” 6x20, 8x14, 9x12, 10x11 10” 5x20, 6x16, 9x10, 8x12
500 10” 10x10,6x8, 8x12, 7x14
600 12” 6x10, 7x18, 8x16, 10x12
800 12” 8x18, 9x15, 10x14, 12x12
1000 14” 10x18, 12x14, 8x24
1200 16” 10x20, 12x18, 14x15
1400 16” 10x25, 12x20, 14x18, 15x16
1600 18” 10x30, 15x18, 14x20
1800 20” 10x35, 15,20, 16x19, 12x30, 14x25
2000 20” 10x40, 12x30, 15x25, 18x20
2200 22” 10x40, 15x25, 20x20
2400 22” 12x40, 16x25, 20x20

12/03/2012 9 GI301

Closed Loop Applications – Closed loop system re-circulates the same water/antifreeze solution through a

closed system of underground high-density polyethylene pipe. As the solution passes through the pipe it
collects heat (in the heating mode) that is being transferred from the relatively warm surrounding soil through
the pipe and into the relatively cold solution. The solution is circulated back to the heat pump that extracts its
heat and then returns to the ground to absorb more heat from the earth. Earth loops must be sized properly for
each particular geographic area and individual capacity requirements.

The TTHERM GEO Series heat pumps are designed to operate

on either vertical or horizontal closed loop applications.

(Figures 1 & 2) Vertical loops are typically installed with a
well drilling rig up to 200 feet (61 meters) deep or more.
Horizontal systems are typically installed with excavating or
trenching equipment approximately six to eight feet (1.8 – 2.4
meters) deep, depending on geographic location and length of pipe used.
Horizontal bored loops are typically installed 15 feet deep.

Figure 1 – Horizontal Closed Loop

Lake or Pond Loops – Closed loop systems may also be used

in lakes or rivers to supply a heat source to the heat pump.
Typically a loop consisting of geothermal pipe can be designed
and placed in an area not much deeper than 12ft (3.7 meters)
deep with some water currents present. In any lake or pond,
municipal and area codes must be observed in regards to a lake
or pond loop. The use of an environmentally friendly loop
fluid like Propylene Glycol should be considered should
damage ever occur to the loop. Consult an IGSHPA or CGC
certified installer for proper lake loop design and installation.
State and local codes apply.

Figure 2 – Vertical Closed Loop

12/03/2012 10 GI301

Mechanical Installation Source Water

WARNING

LOOP DESIGN IS EXTREMELY IMPORTANT FOR PROPER HEAT PUMP OPERATION. INCORRECT LOOP
DESIGN WILL REDUCE HEAT PUMP EFFICIENCY, CAUSE POOR PERFORMANCE OR MAY RENDER THE
SYSTEM UNUSABLE. IF YOU LACK EXPERIENCE DESIGNING LOOP FIELDS, CONTACT AN IGSHPA OR CGC
CERTIFIED GEOTHERMAL LOOP CONTRACTOR FOR PROPER INSTALLATIONS.

Water Connections General – The following pages outline typical piping arrangements for the most common

source water connection options, as well as flushing and filling procedures and antifreeze requirements for closed
loop systems. TTHERM GEO recommends hose kits for the source water connection points at the heat pump. This
will provide a flexible connection to reduce and isolate vibrations transmitting from the compressor into other parts
of the system. Hose kits also provide P/T ports for monitoring pressure and temperature (see below).

Note

TTHERM GEO heat pumps are factory set for open loop. J11 must be removed for proper operation on an antifreeze
protected closed loop. See figure on page 30 for the location of J11.

Once closed loops are completed, they must be pressure tested to at least 60 PSI to insure integrity. Once
pressure is tested, the loop must be purged of all foreign debris and filled with fluid. All air must be removed at
this time by flushing the system. (Table 2) shows approximate fluid volumes.

Pressure/Temperature (P/T) plugs – Should be installed in the adaptor elbow on the entering and

leaving water line of the heat pump on a closed system. (Figure 3) A thermometer can be inserted
into the P/T ports to check entering and leaving water temperatures. A pressure gauge can also be
inserted into these P/T ports to determine the pressure differential between the entering and leaving
water. This pressure differential can then be compared to the engineering specifications data to
determine the flow rate of the system.

A Flow Meter is an important part of the system. It provides a visual indicator of loop flow in GPM. A flow

meter can be installed on either side of the pump pack, but must be installed per manufacturer recommendations
so it reads accurately.

Non Pressurized Loops require an air separator/stand pipe to eliminate air and to hold enough fluid to

compensate for the expansion and contraction of the loop pipe and fluid. Purge and fill valves should be placed
between the loop manifold valves and the insulated pump pack.

Pressurized Loops do not require an air separator. They require purge and fill ports between the loop manifold

valves and the insulated pump pack. After purging a pressurized loop, it should maintain 45 to 60 psi static
pressure. The Geothermal Loop Pipe stretches under pressure so may need to be pressurized above the desired
pressure several times to achieve the recommended static pressure. Pressurized loops must maintain enough
static pressure to compensate for the expansion and contraction of the loop pipe and fluid.

Loop Pump Selection – Select a loop circulation pump based upon the GPM required and total system pressure

drop. See specification, page 4. Geo heat pump Btu/h capacity and efficiency are directly related to the GPM

flow though the unit.
Vibration pad – suggest setting the unit on a sound vibration pad, available from most distributors or

accessories price sheet – E2-0122.

Water quality – models with standard copper heat exchanger coils require the installer to evaluate water quality

and meet minimum water properties.

 pH < 7.5
 Calcium hardness < 100 PPM
 Iron fouling < 0.2 PPM (Ferrous)

< 0.5 PPM of oxygen

 Hydrogen sulfide (H
 Chloride levels < 20 PPM
 Erosion/clogging 10 PPM, particles
 Filter, if required 800 micron size
 Softened water is recommended along with 2 oz of common house chlorine bleach for every 10 gallons of water.

S) < 0.5 PPM

2

P/T Adapter

Figure 3

12/03/2012 11 GI301

Figure 4 – Non-Pressurized Closed Loop with Flow Center – Typical piping arrangement.

Figure 5 – Pressurized Closed Loop with Flow Center – Typical piping diagram.

12/03/2012 12 GI301

Antifreeze

When considering the earth loop solution, water quality is very important. TTHERM GEO recommends a
minimum of soft water (not well water) treated with 2 oz. of household chlorine bleach for each 10 gallons of
total volume. TTHERM GEO’s recommended antifreeze concentration is 22% which will yield a freeze
protection of 18° F. This concentration of glycol requires additional additives to protect the system. TTHERM
GEO recommends Enviro-Guard HD propylene glycol for this reason.

Over antifreeze protecting a loop field decreases pumping capacity when the loop gets cold and reduces thermal
transfer. Under protecting a loop field will cause the THERM GEO heat pump to take action protecting itself
from damage. This action will result in a loss of geothermal capacity, and AUX heat may be required to
maintain the temperature in the home.

Table 2 – Approximate Fluid Volume (gal) per 100ft

Pipe Size Volume Pipe Size Volume

Polyethylene

¾” IPS SDR 11 3.02 1” 4.1
1” IPS SDR 11 4.73
1-1/4” IPS SDR 11 7.55 1” 4.5
1-1/2” IPS SDR 11 9.93 1.25” 6.8
2” IPS SDR 11 15.36

Rubber Hose

Copper

Type M

1.25” 6.4

1.5” 9.5

WARNING

PREVENTING FREEZE-UP IS INSTALLER/USER RESPONSIBILITY. DAMAGE CAUSED BY

FREEZE-UP IS NOT COVERED BY WARRANTY.

CAUTION

Softened water is recommended along with 2 oz. of common household chlorine bleach for every
10 gallons of water.

WARNING

NOT ALL GLYCOLS PROVIDE THE SAME LEVEL OF CONCENTRATION. MOST GLYCOLS

DO NOT CONTAIN ENOUGH INHIBITORS FOR THE RECOMMENDED CONCENTRATION

LEVELS.FOR GEOTHERMAL SYSTEMS.

Open Loop – An open system gets its name from the open discharge of water after it has been used by the heat

pump. A well must be available that can supply all of the water requirements of the heat pump along with any
other water requirements drawing off that same well. The well must be capable of supplying the heat pump’s
required flow rated for up to 24 hours per day for the coldest winter day.

Figure 6 shows the necessary components for water piping of an open system. First a bladder type pressure tank
with a “draw down” of at least 1-1/2 to 2 times the well pump capacity must be installed on the supply side of
the heat pump to prevent short cycling the well pump. Constant pressure well pumps need to deliver the GPM
flow rate of the TTHERM GEO heat pump and other possible consecutive demands. Shut off valves and boiler
drains on the entering and leaving water lines are necessary for future maintenance. A screen strainer is placed
on the supply line with a mesh size of 40 to 60 and enough surface area to allow for particle buildup between
cleanings. Hose kits are installed between the heat pump and ridged plumbing to reduce vibration transfer. Hose
kits have pressure temperature (P/T) plugs placed in the supply and discharge hydrant elbows so that
thermometers or pressure gauges can be inserted into the water stream. On the well water discharge side of the

12/03/2012 13 GI301

heat pump a flow meter is installed to provide a visual indicator of open loop flow in GPM. The water solenoid
valve must be installed to control water flow through the unit. After the water solenoid a flow control valve is
installed to limit maximum flow through the heat pump. The ball valve installed in the leaving water line can be
used to create a small amount of back pressure to quiet the flow control valve if needed. Discharge water
temperature should not drop below 39° at any time during the units operation. Remove handle on the entering
and leaving water ball valves to prevent accidental change of flow.

The solenoid valve is then wired to two leads (brown/yellow and gray) provided. This valve will open when the
unit is running and close when the unit stops. The visual flow meter will allow visual inspection of the flow
requirements, and can be useful in determining when maintenance is required. Schedule 40 PVC piping, copper
tubing, polyethylene or rubber hose can be used for supply and discharge water lines. Make sure line sizes are
large enough to supply the required flow with a reasonable pressure drop (generally 1.00” diameter). Water
discharge is generally made to a drain field, stream, pond, surface discharge, tile line, or storm sewer.

Solenoid Valve Wiring (for Open Loop Systems)

Inside the cabinet, tie-wrapped to the OUT water pipe, are two leads (brn/yel and gray) for direct connection to a
24VAC solenoid.

CAUTION

Using a drain field requires soil conditions and adequate sizing to assure rapid percolation or the required
flow rates will not be achieved. Consult local codes and ordinances to assure compliance. Do not
discharge water to a septic system. The heat pump should never be operated with flow rates (GPM) less
than specified. Discharge water should never be lower than 39° F. Operation of the unit with less than
required flow rate or no flow may result in freezing water in the water to refrigerant heat exchanger.
This will cause the unit to shut down on low-pressure lockout. If the unit locks out low pressure, verify
that the unit has the required flow and reset the unit by shutting off power to the unit for one minute. Do
not continually reset the unit; if the unit locks out more than once call your service professional.
Continued reset of the unit can freeze water inside the water coil to the point of rupturing the water coil

(no warranty for frozen coils).

12/03/2012 14 GI301