T-Tech ES6000, ES8000 User Manual
ES6000/ES8000
Failure to follow instructions may
cause damage or explosion,
always shield eyes. Read entire
instruction manual before use.
WARNING
User’s Manual
Warning: This product contains chemicals,
including lead, known to the State of
California to cause cancer, birth defects
and other reproductive harm.
Wash hands after handling.
Congratulations! You have just purchased the finest quality portable power source and
WARNING
Read these instructions completely before using the Tru ck PAC and save them for future
reference. Before using the Tru ck PAC to jump start a car, truck, boat or to power any
equipment, read these instructions and the instruction manual/safety information
provided by the car, truck, boat or equipment manufacturer. Following all manufacturers’
instructions and safety procedures will reduce the risk of accident.
Working around lead-acid batteries may be dangerous. Lead-acid batteries release
explosive gases during normal operation, charging and jump starting. Carefully read and
follow these instructions for safe use. Always follow the specific instructions in this
manual and on the Tru ck PAC each time you jump start using the Tru ck PAC.
All lead-acid batteries (car, truck and boat) produce hydrogen gas which may violently
explode in the presence of fire or sparks. Do not smoke, use matches or a cigarette
lighter while near batteries. Do not handle the battery while wearing vinyl clothing
because static electricity sparks are generated when vinyl clothing is rubbed. Review all
cautionary material on the Tru ck PAC and in the engine compartment.
Always wear eye protection, appropriate protective clothing and other safety equipment
when working near lead-acid batteries. Do not touch eyes while working on or around
lead-acid batteries.
Always store clamps in their holsters, away from each other or common conductors.
Improper storage of clamps may cause the clamps to come in contact with each other,
or a common conductor, causing the battery to short circuit and generate high enough
heat to ignite most materials.
Use extreme care while working within the engine compartment, because moving parts
may cause severe injury. Read and follow all safety instructions published in the vehicle's
Owner's Manual.
While the battery in the Tru ck PAC is a sealed unit with no free liquid acid, batteries
being jump started with the Tru ck PAC unit likely contain liquid acids which are
hazardous if spilled.
jump starter on the market. We have taken numerous measures in quality control and
in our manufacturing processes to ensure that your product arrives in top condition,
and that it will perform to your satisfaction.
In the rare event that your Truck PAC contains a damaged or missing item, does not
perform as specified, or requires warranty service, please call Technical Service at
(913) 310-1050.
Save your purchase receipt, it is required for warranty service.
This unit has a sealed lead-acid battery that should be kept at full charge. Recharge
when first received, immediately after each use, and every three months if not used.
Failure to perform maintenance charges may cause the battery life to be reduced
greatly.
SAFETY SUMMARY
PERSONAL PRECAUTIONS
Someone should always be within range of your voice or close enough to come to
your aid when you work near a lead-acid battery.
Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing or eyes. Protective eyewear should always be worn when working near
lead-acid batteries.
If battery acid contacts skin or clothing, wash immediately with soap and water. If acid
enters eye, immediately flood eye with running cold water for at least 10 minutes and
get medical attention immediately.
Be extra cautious to reduce risk of dropping a metal tool onto a battery. It might spark
or short circuit the battery or another electrical part that may cause explosion.
Remove personal metal items such as rings, bracelets, necklaces and watches when
working with a lead-acid battery. A lead-acid battery can produce a short-circuit
current high enough to weld a ring or the like to metal, causing a severe burn.
Use the Truck PAC for jump starting
dry-cell batteries that are commonly used with home appliances. These batteries may
burst and cause injury to persons and damage to property.
NEVER charge or jump start a frozen battery.
To prevent arcing,
piece of metal.
NEVER allow clamps to touch together or to contact the same
lead-acid batteries only. Do not use for charging
IMPORTANT SAFETY INSTRUCTIONS
Use of an attachment not recommended or sold by the manufacturer may result in a
risk of damage to the unit or injury to personnel.
When using the wall charger or power extension cord, pull on the plug and
the wire when disconnecting.
Do not recharge the Truck PAC with a damaged wall charger or power extension cord.
Replace them immediately.
The Truck PAC may be used under any weather condition – rain, snow, hot or cold
temperatures.
Do not submerge in water.
Do not operate with flammables such as gasoline, etc.
If the Truck PAC receives a sharp blow or is otherwise damaged in any way, have it
checked by a qualified service person. If the Truck PAC is leaking battery acid, do not
ship it. Take it to the closest battery recycler in your area.
AC. Have it checked by a qualified ser
uck P
Do not disassemble the T
The Truck PAC should never be left in a completely dischar
time. Damage to the battery could be permanent, with poor performance as a result.
When not in use, leave your Truck PAC connected to the wall charger or recharge
every three (3) months.
r
ged state for any period of
never on
vice person.
OPERATION AND MAINTENANCE
Portable Power Source Features
The Truck PAC provides plenty of power for starting vehicles – more than enough to
start most cars, vans, SUVs, light trucks and delivery vehicles.
The Truck PAC will power most 12 Vdc accessories equipped with a male 12 Volt
outlet plug (12 Volt Model ES6000 only). The DC outlet features automatic overload
protection.
The unit features a test switch and LED lights. State of the art circuitry allows the unit
to remain continuously connected to the charger without the risk of overcharging.
Safety Features
Safety storage holsters prevent accidental sparking of clamps and rotate 90° for easy
clamp removal and replacement. Always re-holster the clamps after use.
Cable grooves lock the cables for clean storage (no hazardous or unsightly dangling
wires). Always re-wrap cables and properly secure clamps after each use.
The Truck PAC contains the latest technology with its 12 Volt sealed, non-spillable
battery and may be stored in any position.
RECHARGING PROCEDURES
Note: Upon initial purchase, your Truck PAC should be charged for a minimum of 30
hours.
Figure 2. Test Button, Charging, Power Levels and Charge Complete LEDs
Recharging Your Truck PAC
There are two ways to charge your Truck PAC. The recommended method is
automatic charging with the provided wall charger. An alternative method is through
the DC power outlet using the provided 12 Volt Male-Male Extension Cord (not valid
for 24 Volt Model ES8000). This second method is not automatic and must be
monitored because the Truck PAC could be damaged due to overcharging.
Charging using the supplied wall char
recommended charging method because it featur
the possibility of overcharging. With this method, the wall charger is connected to the
Truck PAC through a small charging jack (pin jack), located on the rear of the unit.
Recharging takes approximately 4 to 6 hours for each light that does not come on
when the test button is pr
connected to the wall charger indefinitely. This is the only method for charging Model
No. ES8000.
essed. W
ger (recommended method).
es automatic charging, eliminating
ith this method, your T
ruck PAC can be left
This is the
1. Insert the wall charger pin into the CHARGING JACK (located in the rear of the
Truck PAC).
2. Connect the wall charger AC/DC ADAPTOR to the AC outlet (the yellow
CHARGING light will light). (See Figure 2.)
3. Allow the Truck PAC to charge until the CHARGE COMPLETE light comes on
(you can monitor the progress by checking the red POWER LEVEL lights –
when all three POWER LEVEL lights are lit the CHARGE COMPLETE light
should come on).
4. Once the CHARGE COMPLETE light comes on, charge another three to six
hours, (three hours is acceptable, but to ensure maximum output capability, six
hours is preferred).
Note: The CHARGING COMPLETE LED indicates that the charging process is
complete. It may illuminate for a short period after the charger is unplugged
from the unit due to the surface charge, but this will only occur for a short time,
which is normal. To assess the unit’s readiness, monitor the Power Level LED’s.
5. If you are not planning to use your Truck PAC right away, you may leave it
connected to the wall charger. We recommend that the wall charger remain
connected to the Truck PAC when not in use.
Charging using the supplied 12 Volt Male-Male Extension Cord. This alternative
charging method may be used when access to an AC outlet is unavailable.
Note: This method can only be used to charge Model No. ES6000. Model No.
ES8000 cannot be charged in this manner.
1. Start the vehicle’s engine.
2. Plug one end of the 12 Volt Male-Male Extension Cord into the Truck PAC
12 Volt outlet and the other end into a vehicle 12 Volt outlet.
3. Press the test button once every hour to check the POWER LEVEL. When all of
the red lights and the CHARGE COMPLETE light come on, charge the Truck
PAC another 1 to 2 hours to insure a complete recharge.
Note: The CHARGING COMPLETE LED indicates that the charging process is
complete. It may illuminate for a short period after the cord is unplugged from
the unit due to the surface charge, but this will only occur for a short time,
which is normal. To assess the unit’s readiness, monitor the Power Level LED’s.
Note: DO NOT OVERCHARGE! This is not an automatic method of charging
the Truck PAC. You must frequently monitor the charging process (POWER
LEVEL indicators by pressing the TEST button) to ensure the unit is not
overcharged. Overcharging will damage your Truck PAC.
OPERATING INSTRUCTIONS
WARNING
Never hook up a 12 Volt DC power sour
ce to a 24 Volt DC vehicle. This will grossly
overcharge the 12 Volt power source and generate flammable gasses that may explode
and cause property damage and/or bodily harm.
Used as an Emergency Jump Starter
Note: For optimum performance, do not store your Truck PAC below 50° when using
as a jump starter. Never charge or jump start a frozen battery.
1. Use in a well ventilated area.
2. Shield eyes. Always wear protective eyewear when working near batteries.
3. Review this instruction manual and the instruction/safety manual provided by
the manufacturer of the vehicle being jump started.
4. Turn ignition off before making cable connections.
5. Clamp the positive (red +) clamp to the positive terminal on the vehicle battery
(for negative ground system), or an alternate vehicle starting point as
recommended by vehicle manufacturer.
6. Clamp the negative (black –) clamp to the vehicle frame (ground).
7. Make sure the cables are not in the path of moving engine parts (belts, fans,
etc.).
8. Stay clear of batteries while jump starting.
9. Start the vehicle (turn on the vehicle ignition).
Note: If the vehicle doesn’t start within 6 seconds, let the Truck PAC cool for 3
minutes before attempting to start the vehicle again or you may damage the
Truck PAC.
10. When the vehicle is started, disconnect the negative (–) battery clamp from the
vehicle frame and return it to its holster.
11. Disconnect the positive (+) clamp and return it to it’s holster.
Used as an Alternative Power Supply for Vehicles - Model ES6000 Only
Your Truck PAC is an essential tool for all who replace automobile batteries.
Most vehicles have electronic components with memory, such as alarm systems,
computers, radios, phones, etc. and when the vehicle’s battery is replaced, the
memory is lost. However
to the 12 Volt outlet on the vehicle, the memories can be saved.
Note: To use the Truck PAC for this purpose, the chosen outlet must be live when the
vehicle is turned OFF. On some vehicles, 12 Volt outlets are deactivated when the
vehicle is turned OFF.
Note: The DC outlet on Model No. ES8000 is a 24 Volt outlet and should not be
connected to vehicle 12 V
, if the power extension cord is plugged from the Truck PAC
olt power outlets.
Used as a Multipurpose Power Supply
Your Truck PAC is also a portable power source for all 12 Vdc accessories equipped
with a male 12 Volt plug. The DC outlet on the Truck PAC has automatic overload
protection.
When your Truck PAC is used with a DC to AC power inverter, it can operate
appliances normally powered by 120 Vac or 220 Vac. Recommended inverter for the
portable power source is 300 watts maximum. For more information, contact your
nearest Truck PAC dealer.
Note: The DC outlet on Model No. ES8000 is a 24 Volt outlet and should only be used
to power 24 Volt accessories.
TROUBLESHOOTING
Problem: 1 or 2 red lights come on, charger is plugged in for 24 hours and there is
no change in status of lights.
Answer: Check charger to see if it is charging. Charger should be warm.
Problem: Charger works well but still no change in status of lights when the wall
charger is connected to the Truck PAC (yellow light is on).
Answer: Possible defective battery or faulty breaker. Try using a device (light, TV,
etc.) with a 12V plug on it to see if it works. If it operates, the Truck PAC
breaker is OK and the battery is the problem.
Problem: All of the lights come on when the charger is plugged into the Truck PAC,
but when the charger is unplugged and the test button pressed, no lights
come on.
Answer: Your Truck PAC has a defective battery which must be replaced.
Problem: The Truck PAC is fully charged but has no power.
Answer: Check where the wire meets the jaw on the Truck PAC clamp. Make sure
they are well crimped.
Problem: When trying to use an accessory through the 12 Volt outlet on the Truck
PAC, I heard a clicking sound coming from inside the Truck PAC.
Answer: The accessory is drawing too many amps, causing the internal circuit
breaker to cycle ON and OFF. There may be a problem with the
accessory (such as a short circuit) that is causing the overload condition.
QUESTIONS & ANSWERS
Question: How many jump star
needing to be r
Answer: 1 to 30. Factors impacting this ar
vehicle being jump started, engine type and size.
ts can a fully char
ged?
echar
ged T
e temperatur
m before
for
AC per
uck P
r
e, general condition of the
Question: Can the Truck PAC's battery be replaced?
Answer: Yes, call Technical Service at (913) 310-1050 (U.S.).
Question: Can the Truck PAC be recycled?
Answer: Yes, the environment was one of our main concerns in the development
and design of the Truck PAC. Most battery outlets can dispose of this
product at its life's end. In fact, your Truck PAC contains a sealed, nonspillable lead acid battery and
Battery Removal and Disposal Instructions.
Question: What is the ideal in-use temperature of the Truck PAC?
Answer: Room temperature. The Truck PAC will also operate at below zero
temperatures, however its power will be reduced. Intense heat will
accelerate self discharge of the Truck PAC battery.
Question: I have a regular 10 amp battery charger, can I use it to recharge the
Truck PAC?
Answer: No, only the supplied wall charger should be used.
Question: Is the Truck PAC goof proof?
Answer: No, jump starting instructions must be followed. Read and understand all
safety and operating instructions in this manual and those found in the
owner’s manual of any vehicle being jump started before using your
Truck PAC.
Question: I'm recharging my Truck PAC. Should the green CHARGE COMPLETE
light immediately come on?
Answer: No. First the yellow CHARGING light will come on to indicate the
charging process is beginning. Then, the red POWER LEVEL lights come
on in sequence as the level of charge increases. Finally, the green
CHARGE COMPLETE light will come on, but only when the Truck PAC
approaches full charge.
Question: How long should I charge the Truck PAC?
Answer: It should be charged for a minimum of 30 hours when new. Your Truck
PAC can be left on the wall charger continuously. When recharging with
the wall charger, the Truck PAC should be charged for 4 to 6 hours per
light that remains unlit when the TEST button is pressed.
Question: How do I know when the Truck PAC is fully charged?
Answer: Follow all charging instructions. Remove the Truck PAC from the wall
charger and press the TEST button. If all power indicator lights come on,
it is fully charged.
Question: How can I test the battery in my Truck PAC to see if it needs to be
replaced?
Answer: We recommend that you use a 100 amp battery load tester. Load the
Truck PAC battery for 6 seconds with a 100 amp load and it should
maintain at least 9 Vdc.
proper disposal is required by law. See
TESTING THE BATTERY
Pb
After fully charging the battery so all red lights come on, apply a 100 amp load to the
vehicle charging plug (on the Truck PAC), for a period of 6 seconds, while monitoring
the battery voltage (at the vehicle charging plug). The battery is good if the voltage is
9.5 Vdc or higher.
BATTERY REMOVAL AND DISPOSAL INSTRUCTIONS
CONTAINS SEALED LEAD-ACID BATTERY.
BATTERY MUST BE RECYCLED.
The battery inside this product is a sealed lead-acid battery. It is required by law to
be removed and recycled or disposed of properly. While there are federal regulations
that must be complied with throughout the United States, your individual state or local
governments may have additional regulations to be followed.
When the battery in this product is in need of replacement, remove it according to the
instructions provided below and take it to your local recycling center for proper
recycling or disposal. If you don’t have a local recycling center that handles sealed
lead-acid batteries, contact your local environmental agency for instructions.
Removal Instructions
Begin by making sure that both clamps are securely stowed in their holsters on each
side of the Truck PAC.
1. Lay the Truck PAC down on its front. Locate the 13 screws that hold the case
together (four on the left edge, four on the right edge, four along the bottom
and one under the front label).
2. Remove the 13 screws, then lift off the back half of the case.
3. On the top of each battery are two terminals, each with wires connected to
them. Disconnect these wires from the top battery first, by removing the bolts
that hold them to the battery terminals. Disconnect these wires from the
bottom battery by removing the bolts that hold them to the battery terminals.
To prevent accidental arcing, be careful not to touch both battery terminals with
the tools being used to remove the bolts.
4. Lift the batteries out of the front half of the case.
WARRANTY
Clore Automotive warrants this product to be free from defects in material or
workmanship for a period of one year from the date of original end user purchase.
This warranty extends to each person who acquires lawful ownership within one year
of the original retail purchase, but is void if the product has been abused, altered,
misused or improperly packaged and damaged when returned for repair.
This warranty applies to the product only and does not apply to any accessory items
included with the product which are subject to wear from usage; the replacement or
repair of these items shall be at the expense of the owner.
THE TERMS OF THE CLORE AUTOMOTIVE LIMITED WARRANTY CONSTITUTE THE
BUYER’S SOLE AND EXCLUSIVE REMEDY. THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN
DURATION TO THIS EXPRESS WARRANTY. AFTER 1 YEAR FROM DATE OF
PURCHASE, ALL RISK OF LOSS FROM WHATEVER REASON SHALL BE PUT UPON
THE PURCHASER.
CLORE AUTOMOTIVE SHALL NOT BE LIABLE FOR INCIDENTAL AND
CONSEQUENTIAL DAMAGES UNDER ANY CIRCUMSTANCES: CLORE
AUTOMOTIVE’S LIABILITY, IF ANY, SHALL NEVER EXCEED THE PURCHASE PRICE
OF THIS MACHINE REGARDLESS OF WHETHER LIABILITY IS PREDICATED UPON
BREACH OF WARRANTY (EXPRESS OR IMPLIED), NEGLIGENCE, STRICT TORT OR
ANY OTHER THEORY.
Some states do not permit the limitation of warranties or limitation of consequential or
incidental damages, so the above disclaimer and limitation may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Instructions for obtaining service under this warranty:
If this product fails within the first 30 days after retail purchase due to a defect in
material or workmanship, return it to your place of purchase for an exchange.
From day 31 to day 365 after retail purchase, contact Clore Automotive Technical
Service at the number below for warranty service. A valid, dated sales receipt is
required to obtain service under this warranty.
Registering Your Purchase
For best service and to receive periodic product updates, follow the instructions below
to register your purchase:
Please visit: www.cloreregistration.com
Click on the Truck PAC logo
Complete the information in the web form and click “submit”
It’s that easy!
For answers to questions concerning use, out-of-warranty service, or warranty/service
information on this or other Clore Automotive products, contact:
Clore Automotive Technical Service
800.328.2921
913.310.1050
www.cloreautomotive.com
Loading...