TSC Auto ID Technology RFWKD Users Manual
RF-WKD
Wi-Fi module
MANUAL
USER’S
Copyright Information
©2014 TSC Auto ID Technology Co., Ltd,
The copyright in this manual, the software and firmware in the printer described therein are
owned by TSC Auto ID Technology Co., Ltd, All rights reserved.
Information in this document is subject to change without notice and does not represent
a commitment on the part of TSC Auto ID Technology Co. No part of this manual may be
reproduced or transmitted in any form or by any means, for any purpose other than the
purchaser’s personal use, without the expressed written permission of TSC Auto ID Technology
Co.
Agency Compliance and Approvals
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions
and the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter. End-users and installers must be
provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: "Contains FCC ID: VTV-RFWKD ” and "Contains IC: 10524A-RF-WKD “
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
This device is slave equipment, the device is not radar detection and not ad-hoc operation in
the DFS band.
This radio transmitter FCC ID: VTV-RF-WKD has been approved by FCC to operate with
the antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Antenna List
No. Manufacturer Part No. Antenna Type Peak Gain
1 ARISTOTLE
ENTERPRISES INC.
2 ARISTOTLE
ENTERPRISES INC.
RFA-25-P393B-70-85-L FPC 3.2 dBi for 2.4 GHz
3.1 dBi for 5 GHz
RFA-25-P393B-70B140R FPC 0.9 dBi for 2.4 GHz
3.2 dBi for 5 GHz
Note: The antenna connector is I-PEX type.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit
pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les
interférences qui peuvent affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio
frequency exposure limits. The Wireless Device should be used in such a manner such that
the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits
under mobile exposure conditions. (antennas are greater than 20cm from a person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition
aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à
minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux
RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont
supérieures à 20 cm à partir du corps d'une personne).
This radio transmitter IC: 10524A-RF-WKD has been approved by Industry Canada to
operate with
the antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Cet émetteur radio IC: 10524A-RF-WKD a été approuvé par Industrie Canada pour
fonctionner avec les types d'antennes énumérés ci‐dessous avec le gain maximal
admissible et impédance d'antenne requise pour chaque type d'antenne indiqué. Types
d'antennes n'est pas inclus dans cette liste, ayant un gain supérieur au gain maximal
indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil.
Antenna List
No. Manufacturer Part No. Antenna Type Peak Gain
1 ARISTOTLE
ENTERPRISES INC.
2 ARISTOTLE
ENTERPRISES INC.
RFA-25-P393B-70-85-L FPC 3.2 dBi for 2.4 GHz
3.1 dBi for 5 GHz
RFA-25-P393B-70B140R FPC 0.9 dBi for 2.4 GHz
3.2 dBi for 5 GHz
Note: The antenna connector is I-PEX type.
1. Introduction
Product Introduction
The RF-WKD is an 802.11 a/b/g/n Wi-Fi module which supports 2 dual-band external
antennas. The module provides serial UART interface, enabling connection to any
embedded design utilizing a 32-bit microcontroller via simple commands.
The RF-WKD Wi-Fi module is compatible with other devices that use 802.11 a/b/g/n
technology. For more information, please refer the contents in this document.
Loading...