TSC TDP-244 Series, TDP-245 Series, TDP 245-Plus, TDP-247 Series, TDP-345 Series User Manual
...
TDP-244/ TDP-245/ TDP-245 Plus/ TDP-247/
TDP-345 Series
USER’S
MANUAL
DIRECT THERMAL BAR CODE PRINTER
i
COPYRIGHT DECLARATION ....................................................................................................... 1
COMPLIANCES ......................................................................................................................... 1
1. Introduction ................................................................................................................. 3
2. Getting Started ............................................................................................................ 3
2.1 Unpacking and Inspection ...................................................................................... 3
2.2 Equipment Checklist ............................................................................................... 3
2.3 Printer Parts ............................................................................................................ 5
2.3.1 Front View ....................................................................................................... 5
2.3.2 Rear View ........................................................................................................ 5
3 Setup ............................................................................................................................. 6
3.1 Setting Up the Printer ............................................................................................. 6
3.2 Loading Label Stock ............................................................................................... 7
3.3 Peel-Off Installation Assembly (Option) ................................................................. 9
3.4 Loading Label for Peel-off Mode (Option) ............................................................ 12
3.5 External Label Roll Mount Installation (Option) .................................................... 14
3.6 Cutter Module Installation (Option) ....................................................................... 15
3.7 Loading Label in Cutter Mode .............................................................................. 18
3.8 Diagnostic Tool ..................................................................................................... 19
3.8.1 Start the Diagnostic Tool ............................................................................... 19
3.8.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………) ........ 20
3.9 Setting Ethernet by Diagnostic Utility (Option) ..................................................... 21
3.9.1 Using USB interface to setup Ethernet interface .......................................... 21
3.9.2 Using RS-232 interface to setup Ethernet interface ..................................... 22
3.9.3 Using Ethernet interface to setup Ethernet interface .................................... 23
3.10. Install Memory Card .......................................................................................... 25
4. Power on Utilities ...................................................................................................... 27
4.1 Gap/Black Mark Sensor Calibration ..................................................................... 27
4.2 Gap/Black Mark Calibration, Self-test, Dump Mode ............................................. 28
4.3 Printer Initialization ............................................................................................... 33
4.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor . 34
4.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor ....................... 34
4.6 Skip AUTO.BAS ................................................................................................... 34
5. Maintenance .............................................................................................................. 35
5.1 Cleaning................................................................................................................ 35
6. Troubleshooting ........................................................................................................ 37
Contents
ii
LED Status .................................................................................................... 37
Print Quality ................................................................................................... 38
7. LED and Button Operation ....................................................................................... 39
7.1 LED ....................................................................................................................... 39
7.2 Button Operation .................................................................................................. 39
Revise History ............................................................................................................... 43
1
Copyright Declaration
Information in this subject to change without notice and does not represent a
commitment on the part of TSC Auto ID Technology Co., Ltd.. No part of this manual
may be reproduced or transmitted in any form by any means, for any purpose other than
the purchaser’s personal use, without the expressed written permission of T TSC Auto
ID Technology Co., Ltd..
Compliances
CE Class B:
EN55022: 1998+A1: 2000+A2: 2003
EN55024: 1998+A1: 2001+A2: 2003 IEC 61000-4 Series
EN61000-3-2: 2006 & EN61000-3-3: 1995+A1: 2001
FCC Part 15, Class B
UL, CUL
C-Tick:
CFR 47, Part 15/CISPR 22 3rd Edition: 1997, Class B
ANSI C63.4: 2003
Canadian ICES-003
TÜ V/Safety: EN60950: 2000
Wichtige Sicherheits-Hinweise
1. Bitte essen Sie diese Hinweis sorgfältig durch.
2. Heben Sie diese Anleitung fűr den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie
keine Flüssig-oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes
Tuch zur Reinigung.
4. Die Netzanschluß-Steckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schűtzen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.
7. Beachten Sie beim Anschluß ans Stromnetz die Anschlußwerte.
8. Dieses Gerät kann bis zu einer Außentemperatur von maximal 40℃ betrieben
werden.
2
CAUTION
1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER BODY
PARTS AWAY.
2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY
CR2032 INSTALLED. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE.
3. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS.
B 급기기
(가정용 정보통신기기)
이 기기는 가정용으로 전자파 적합등록을 한 기기로서
주거지역에서는 물론 모든 지역에서 사용할 수 있습니다.
3
4. Introduction
Thank you for purchasing the TSC TDP-245/245 Plus/247/345 Series Direct Thermal
Bar Code Printer. Although it is a compact desktop printer, it is reliable and with superior
throughput performance.
This printer provides direct thermal printing at user selectable speed of: 2.0, 3.0, 4.0, 5.0,
6.0 or 7.0 inches per second. It accepts roll feed, die-cut, and fan-fold labels for direct
thermal printing. All common bar codes formats are available. Fonts and bar codes can
be printed in 4 directions, 8 different alphanumeric bitmap fonts and a build-in true type
font capability. You will enjoy high throughput for printing labels with this printer.
2. Getting Started
2.1 Unpacking and Inspection
This printer has been specially packaged to withstand damage during shipping. Please
carefully inspect the packaging and printer upon receiving the bar code printer. Please
retain the packaging materials in cover you need to reship the printer.
2.2 Equipment Checklist
Printer
BarTender UltraLite CD disk
Quick start guide
USB port cable
External universal switching power supply
Power Cord
Label Spindle
Fixing tab x2
1.5” core adapter x2
If any parts are missing, please contact the Customer Service Department of your
purchased reseller or distributor.
4
Dealer option
Peel off module assembly.
Regular cutter (Guillotine cutter)
Full cut: Paper thickness: 0.06~ 0.19mm, 500,000 cuts
Paper thickness: 0.19mm 200,000 cuts
Partial cut: Paper thickness: 0.06~0.12mm, 500,000 cuts
Note: Except for the linerless cutter, all regular/heavy duty/care label cutters DO
NOT cut on media with glue.
Main board integrated with internal Ethernet
Internal Ethernet print server module
User option
KP-200
KU-007 plus
External Ethernet print server
External wireless (802.11b/g) print server
External roll mount, media OD. 214 mm (8.4”) with 3” core label spindle
Contact CCD contact scanner
Long range linear image bar code scanner
5
2.3 Printer Parts
2.3.1 Front View
2.3.2 Rear View
Note: The interface picture here is for reference only. Please refer to the product specification for
the interfaces availability.
1
2 3 4 5 6
1. USB Interface
2. Centronics Interface
3. RS-232C DB-9 Interface
4. Power Jack
5. Power Switch
6. Rear Label Guide
Top Cover Open Lever
LED Indicator
Feed Button
Top Cover
Clear Window
Backing Paper Opening
Label Opening
Front Panel
6
3 Setup
3.1 Setting Up the Printer
1. Place the printer on a flat, secure surface.
2. Make sure the power switch is off.
3. Connect the printer to the computer with the Centronics or USB cable.
4 Plug the DC power cord into the power jack at the rear of the printer, and then
plug the AC power cord into a properly grounded receptacle.
Note: When plug power code into the rear of printer please make sure the printer power switch is
off.
Power Cord
Power Switch
Power Supply
Plug
USB
RS-232C
Centronics
Power Jack
7
3.2 Loading Label Stock
1. Insert a 1” label spindle into a paper roll (If your paper core is 1 inch, remove the 1.5
inch core adapter from the fixing tab).
2. Open the printer’s top cover by releasing the green top cover open levers located
on both sides of the printer and lifting the top cover.
3. Place a roll of paper into internal paper roll mount.
4. Feed the paper, printing side face up, through the label guides and place the label
over the platen.
5. Adjust the black center-biased label guides in or out by turning adjustment knob so
they are slightly touch the edges of the label backing.
Label Roll
1” Label Spindle
Label Roll Mount
Platen
1.5” Core Adapter
Adjustment Knob
Fixing Tab
Label Guide
Printing Side Face up
8
6. Close the printer top cover slowly and make sure the cover locks levers securely.
Note: Failure to securely close and lock the cover will result in poor print quality.
Please refer to videos on TSC YouTube or driver CD.
9
3.3 Peel-Off Installation Assembly (Option)
1. Open the top cover.
2. Unscrew the 6 screws in the lower inner cover.
3. Upside down the printer.
4. Unscrew the 2 screws at the lower inner cover
5. Remove the screw at memory card cover.
Remove the
screw
Remove the
screw
Screw
Screws
Screws
10
6. Hold the lower cover and lift up the top cover opening levers to separate the lower
inner cover from the lower cover.
7. Thread the harness red connector through the cable hole at the front side of lower
inner cover. Plug the red peel off module harness connector at the location JP17
(TDP-245) / JP19 (TDP-245 Plus/TDP-247/TDP-345) on the main board. Place
lower inner cover to the lower cover. Install the peel-off module to the lower inner
cover slot.
8. Gently push peel-off panel to lock to the lower inner cover.
9. Reassemble parts in reverse procedures after installing the module.
Lower inner
cover
Lower cover
Peel-off module
assembly
Install one side first
and install another
side
11
12
3.4 Loading Label for Peel-off Mode (Option)
1. Open the peel-off module by pulling it out.
2. Thread the label, printing side facing up, through the label guides and place it on top
of the platen.
3. Thread the label through the liner opening, which is beneath the roller.
4. Adjust the black center-biased label guides by turning adjustment knob to fit the
edge of the label backing.
5. Push the peel-off panel back to the printer.
6. Close the top cover.
Note:
Please refer to videos on TSC YouTube or driver CD.
Peel-off Panel
Peel-off Roller
Roller
Adjustment Knob
Peel-off panel
Loading...