
Limited One Year Warranty
T&S warrants to the original purchaser (other than
for purposes of resale) that such product is free from
defects in material and workmanship for a period of
one (1) year from the date of purchase. During this
one-year warranty period, if the product is found to
be defective, T&S shall, at its options, repair and/
or replace it. To obtain warranty service, products
must be returned to...
T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690
Shipping, freight, insurance, and other transportation charges of the product to T&S and the return
of repaired or replaced product to the purchaser are
the responsibility of the purchaser. Repair and/or
replacement shall be made within a reasonable time
after receipt by T&S of the returned product. This
warranty does not cover Items which have received
secondary finishing or have been altered or modified after purchase, or for defects caused by physical abuse to or misuse of the product, or shipment
of the products.
Any express warranty not provided herein, and
any remedy for Breach of Contract which might arise,
is hereby excluded and disclaimed. Any implied
warranties of merchantability or fitness for a particular purpose are limited to one year in duration. Under
no circumstances shall T&S be liable for loss of
use or any special consequential costs, expenses
or damages.
Some states do not allow limitations on how long
and implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply
to you. Specific rights under this warranty and other
rights vary from state to state.
P/N: 098-005911-45 Rev.3
Date: 980507
Drawn: CW
Checked: MAB 7-23-98
Approved: MVW 7-23-98
Installation and
Maintenance
Instructions
B-0870 Series Lavatory
Faucets with or without
Pop-Up
Deutsch: Installations- und
Wartungsanleitungen
Español: la Instalación y las
Instrucciones de
Mantenimiento
Français: les Instructions
d’Installation et
d’Entretien

Exploded View
B-2970
11
10
12
9
6
14
16
15
12
11
13
2
3
4
5
* Some items are listed for instructional purposes
and may not be sold as separate parts.

Part Number Guide
Faucet Assemblies
1 Base Faucet *
2 Shank, Faucet *
3 Washer, Rosette 001000-45
4 Locknut 002954-45
5 Nut, Coupling 000958-20
6 Aerator, 13/16" MA B-0199-03
7 Asm, Drain w/Pop-Up B-0898
8 Asm, Spindle - Eterna LH 002713-40
Asm, Spindle - Eterna RH 002714-40
9 Spindle - Cold 005959-40
Spindle - Hot 005960-40
10 Handle - Cold 001636-45
Handle - Hot 001635-45
11 Index, Button - Blue (Cold) 001660-45
Index, Button - Blue (Hot) 001661-45
12 Screw, Handle 000922-45
13 Asm, Eterna Spindle - Hot 005960-40
14 Handle, Alpine - Lexan 001144-45
15 Screw, Lab Handle 000925-45
16 Index Button, Handle (Cold) 001327-40
Index Button, Handle (Hot) 001328-40
17 Handle, Lavatory, 3 Wing (Cold) 001784-40
Handle, Lavatory, 3 Wing (Hot) 001783-40

Installation: (Faucet)
1. Turn off water supply and drain
lines. Drill (2) two 1” diameter
holes, 4” center-to-center in sink
top where you will be installing
no.1.
2. After unpacking, remove no.5,
no.4 and no. 3 from each no.2.
1
2
3
4
5
sink
3. Place no.1 into holes in sink top
and replace no.3, no.4 and no.5 onto
no.2. Tighten no.5 with a wrench.
‘o’-ring
pop-up drain
stopper
stem
flange
screw
rubber washer
washer
locknut
ball rod
gasket
nut
drain body
lift rod
rod clip
3. Insert drain body from bottom
of sink drain hole, reassemble
flange to drain body, tightening
as far possible.
flange
drain pipe
4. Connect water supply lines and
check for leaks.
Installation: (Pop-Up Valve)
1. Remove pop-up drain stopper, with
‘o’-ring and flange from pop-up
assembly.
2. Remove rod clip, lift rod, rod guide
nut, rubber washer and rod ball
assembly from drain body.
drain body
sink base
flange flush with
sink bottom
washer
locknut
rubber
washer
4. Slide rubber washer on drain
pipe up against bottom of sink.
Tighten washer and locknut
firmly against base for a tight seal.