T&S Brass B-2710 Installation Manual

Limited One Year Warranty

T&S warrants to the original purchaser (other than
for purposes of resale) that such product is free from
defects in material and workmanship for a period of
one (1) year from the date of purchase. During this
one-year warranty period, if the product is found to
be defective, T&S shall, at its options, repair and/
or replace it. To obtain warranty service, products
must be returned to...

T&S Brass and Bronze Works, Inc.

Attn: Warranty Repair Department

2 Saddleback Cove

Travelers Rest, SC 29690

Shipping, freight, insurance, and other transpor­tation charges of the product to T&S and the return
of repaired or replaced product to the purchaser are
the responsibility of the purchaser. Repair and/or
replacement shall be made within a reasonable time
after receipt by T&S of the returned product. This
warranty does not cover Items which have received
secondary finishing or have been altered or modi­fied after purchase, or for defects caused by physi­cal abuse to or misuse of the product, or shipment
of the products.

Any express warranty not provided herein, and
any remedy for Breach of Contract which might arise,
is hereby excluded and disclaimed. Any implied
warranties of merchantability or fitness for a particu­lar purpose are limited to one year in duration. Under
no circumstances shall T&S be liable for loss of
use or any special consequential costs, expenses
or damages.

Some states do not allow limitations on how long
and implied warranty lasts or the exclusion or limi­tation of incidental or consequential damages, so
the above limitations or exclusions may not apply
to you. Specific rights under this warranty and other
rights vary from state to state.

Installation and

Maintenance

Instructions

B-2730 & B-2731
SERIES

SINGLE LEVER FAUCETS
(with or without Sidespray)

Español: la Instalación y las

Instrucciones de
Mantenimiento

P/N: 098-013123-45 Rev.3

Date: 03-01-04

Drawn: TEH

Checked:

Approved:

MVW 04-30-04
MVW 04-30-04

Exploded View

* Some items are listed for instructional purposes

and may not be sold as separate parts.

2

Part Number Guide

Single Lever Lavatory Faucet Assembly

Asm, Single Lever Faucet w/ Sidespray B-2730
Asm, Single Lever Faucet B-2731

1 Body, Faucet *

Center Mounting Kit 014163-45
2 Spacer, Foam *
3 Washer, Lock *
4 Post, Center Mounting *
5 Locknut, Center Mounting Post *
6 Deckplate *
7 Gasket, Mounting

Plastic 014160-45
Zinc 014161-45

Kit, Side Mounting Post & Locknut 014162-45
8 Post *
9 Locknut *

10 Sidespray

4ft. Hose 013842-45

7ft. Hose (B-2730-07) 012975-45
11 Retaining Ring *
12 Retaining Nut *
13 Cartridge, Metal Stem w/ Temp. Limit Stop 013080-45
14 Handle

Standard 013113-45

Long 013429-45
15 Plug 014173-45
16 * Hex Key, 3/32" 010587-45
17 Post, Sidespray Connection *
18 Flexible Stainless Steel Supplies *
19 Hose Guide 001496-45
20 Locknut, Hose Guide *

* Hex Key not provided

3

General Instructions

Faucet Installation

1. Shut off water supply and drain lines. Clean sink surface thoroughly.

2. Place no.6 with no.7 on deck in line with mounting holes.

3. Hand tighten no.18 into no.1. Carefully slide no.18 through center sink hole.

4. Insert no.8 under deck and thread tightly into no.6. Thread no.9 onto no.8 and
tighten fully against underside of countertop.

5. Insert no.4 into no.1 tightly. Slide no.2 and no.3 onto no.4. Thread no.5 onto
no.4. Tighten fully against underside of countertop.

6. Place no.19 into hole in countertop. Thread no.20 onto no.19 and tighten fully
against underside of countertop.

7. Slide no.10 through no.19. Connect no.10 to outlet no.17.

8. Connect water supply lines and check for leaks.

14

11

6
7

9

8

1

sink

18

17

2

3

5

4

10
19

20

Maintenance:

1. To change no.13, remove no.15 by hand.

2. Insert no.16 into hole of no.14 and loosen set screw of no.14. Remove no.14.

3. Unscrew no.11 by hand and remove.

4. Unscrew no.12 by hand and remove.

5. Remove no.13 and replace with new no.13.

6. Replace no.12, no.11 and no.14 and tighten set screw.

7. Replace no.15.

4

General Instructions

1. Remove no.15, then using
no.16, loosen set screw and
lift off no.14

2. Unscrew no.11.

3. Unscrew no.12.

4. Adjust no.13 to desired
position per below.

Figure 1

Normal factory
set position
allows full
mixing of hot
and cold water.

Figure 2

Place ring into
this position to
reduce the
amount of hot
water available.
Result: cold to
warm water only.

Figure 4

Using needle
nose pliers,
carefully lift off
the temperature
limit stop ring
from the cartridge
body. Re-set the
ring onto the
body per Figure 4
or 5.

Place ring into
this position to
reduce the
amount of cold
water available.
Result: warm to
hot water only.

Figure 3

Figure 5

5

Instrucciones

Generales

Instalación de la canilla:

1.Cierre la fuente principal de agua y desagüe las tuberías. Limpie muy bien la
superficie del lavatorio.

2. Coloque la parte No.6 con la parte No.7 sobre la cubierta en línea con los
huecos de montadura.

3. Apriete a mano la parte No.18 a la parte No.1 Cuidadosamente deslice la parte
No.18 a través del hueco del centro del lavatorio.

4. Ensarte la parte No.8 a la parte No.6 por debajo de la cubierta y apriete
aseguradamente. Enrosque la parte No.9 en la parte No.8 y apriete por completo
contra la parte de abajo del mostrador.

5. Ensarte la parte No.4 dentro de la parte No.1 apretadamente. Deslice las parte
No.2 y No.3 en la parte No.4. Enrosque la parte No.5 en la parte No.4. Apriete por
completo contra la parte de abajo del mostrador.

6. Coloque la parte No.19 en el hueco del mostrador. Enrosque la parte No.20 en la
parte No.19 y apriete por completo contra la parte de abajo del mostrador.

7. Deslice la parte No.10 a través de la parte No.19. Conecte la parte No.10 a la
línea de salida No.17.

8. Conecte las líneas de surtido e inspeccione por filtraciones.

14

11

6

1

7

10
19

9
8

17
18

2
3

5

4

Lavatorio

20

Mantenimiento:

1. Para cambiar la parte No.13, remueva a mano la parte No.15.

2. Ensarte la parte No.16 en el hueco de la parte No.14 y afloje el tornillo presión
de la parte No.14. Remueva la parte No.14.

3. Destornille la parte No.11 y remuévala.

4. Destornille la parte No.12 y remuévala.

5. Remueva la parte No.13 y reemplace con una parte nueva No.13.

6. Reemplace la parte No.12, No.11 y la parte No.14. Apriete el tornillo de presión.

7. Reemplace la parte No.15.

6

Instrucciones

Generales

1. Remueva la parte No.15, luego
afloje el tornillo de presión
utilizando la parte No.8, y
remueva la parte No.14 alzándola.

2. Destornille la parte No.11.

3. Destornille la parte No.12.

4. Ajuste la parte No.13 a la
posición deseada como lo indica
abajo.

Dibujo 1

La posición
ajustada en la
factoría permite
la mayor mezcla
de agua fría y
caliente.

Dibujo 2

Coloque la
argolla en esta
posición para
reducir la
cantidad de
agua caliente
disponible.
Resultado:
Solamente agua
tibia a fría.

Cuidadosamente
levante la argolla de
limitación de
temperatura del
cuerpo del cartucho
utilizando alicates
de punta. Coloque
de nuevo la argolla
dentro del cuerpo
como indicado en el
dibujo 4 o 5.

Dibujo 3

Coloque la argolla
en esta posición
para reducir la
cantidad de agua
fría disponible.
Resultado:
Solamente agua
tibia a caliente.

Dibujo 5Dibujo 4

7

B-2710 & B-2711

Single Lever

Faucets

T&S BRASS AND BRONZE WORKS, INC.

A firm commitment to application-engineered plumbing products
2 Saddleback Cove, P.O. Box 1088, T & S Brass-Europe

Travelers Rest, SC 29690 ‘De Veenhoeve’
Phone: [phone] Oude Nieuwveenseweg 84
Fax: [phone] CW Nieuwveen

E-mail: [e-mail] The Netherlands