T&S Brass B-2701 Installation Manual

Limited One Year Warranty

T&S warrants to the original purchaser (other
than for purposes of resale) that such product is
free from defects in material and workmanship
for a period of one (1) year from the date of
purchase. During this one-year warranty period,
if the product is found to be defective, T&S shall,
at its options, repair and/or replace it. To obtain
warranty service, products must be returned
to...

T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department

2 Saddleback Cove

Travelers Rest, SC 29690

Shipping, freight, insurance, and other
transportation charges of the product to T&S
and the return of repaired or replaced product
to the purchaser are the responsibility of the
purchaser. Repair and/or replacement shall be
made within a reasonable time after receipt by
T&S of the returned product. This warranty does
not cover Items which have received secondary
fi nishing or have been altered or modifi ed after
purchase, or for defects caused by physical
abuse to or misuse of the product, or shipment
of the products.
Any express warranty not provided herein, and
any remedy for Breach of Contract which might
arise, is hereby excluded and disclaimed. Any
implied warranties of merchantability or fi tness
for a particular purpose are limited to one year in
duration. Under no circumstances shall T&S be
liable for loss of use or any special consequential
costs, expenses or damages.
Some states do not allow limitations on how
long and implied warranty lasts or the exclusion
or limitation of incidental or consequential dam­ages, so the above limitations or exclusions may
not apply to you. Specifi c rights under this war-
ranty and other rights vary from state to state.

Installation and

Maintenance

Instructions

B-2701, B-2703,
B-2710 & B-2711
SERIES

SINGLE LEVER FAUCETS
(with or without Pop-Up)

P/N: 098-013122-45 Rev.4
Date: 02-16-09
Drawn: TEH
Checked: DMH 03-18-09
Approved: JHB 03-20-09

Exploded View

B-2701 & B-2703 Series

6

8

712

10

11

1

5*

13

14

15

*

Some items are listed for instructional purposes

and may not be sold as individual parts.

2

Exploded View

B-2710 & B-2711 Series

* Some items are listed for instructional purposes

and may not be sold as separate parts.

3

Part Number Guide

1

Asm, Single Lever Rigid Base Faucet
Asm, Single Lever Rigid Base Faucet w/ 4” Deckplate
Asm, Single Lever Faucet w/ Pop-Up Drain
Asm, Single Lever Faucet

2

Gasket, Waterproof

3

Lock Washer

4

Lock Nut
Kit, Lock Washer and Lock Nut

5

Faucet Body

6

Handle

7

Plug

8

3/32” Hex Key (not included)

9

Pop-Up Drain

10

Cartridge, Metal Stem w/ Temperature Limit Stop

11

Retaining Nut

12

Retaining Ring

13

4” Deckplate

14

C-Ring

15

Lock Nut

B-2701
B-2703
B-2710
B-2711
014167-45
000999-45
016673-45
014166-45
*
013113-45
014173-45
010587-45
B-0898
013111-45
016663-45
016661-45
013824-40
016842-45
016841-40

4

General Instructions

Faucet Installation (B-2701 & B-2703)

(Refer to diagram on page 2)

1. Shut off water supply lines. Drill a 1-1/2”
diameter hole in countertop where no.5 will
be installed.

2. Clean countertop and bottom of no.5. Ap­ply putty to bottom of no.5.

3. If installing no.13, apply putty to bottom
contact face of no.13.

4. With no.14 and no.15 removed place hoses
and threaded rod at bottom of no.5 through
the 1-1/2” diameter hole.

5. Place no.14 and no.15 on threaded rod and
tighten.

6. Connect water supply and check for leaks.

Faucet Installation (B-2710 & B-2711)

(Refer to diagram below)

1. Shut off water supply and drain lines.
Clean sink surface throughly.

2. Install no.5 with no.2 on top of the deck
or sink.

3. Place no.3 and no.4 on the shank of no.5
and tighten fully.

o-ring
pop-up drain

stopper

stem

fl ange

screw

rubber washer

washer

locknut

ball rod

gasket

nut

drain body

3. Insert drain body from bottom of sink
drain hole, reassemble fl ange to drain
body, tightening as far possible.

fl ange

sink base

lift rod

rod clip

drain pipe

drain
body

2

3
4

4. Connect water supply lines and check
for leaks.

deck

5

Pop-Up Valve Installation

1. Remove pop-up drain stopper, with o­ring and fl ange, from pop-up assembly.

2. Remove rod clip, lift rod, rod guide nut
and rod ball assembly from drain body.

fl ange fl ush with
sink bottom

washer

locknut

4. Slide rubber washer on drain pipe up
against bottom of sink. Tighten washer
and locknut fi rmly against base for a tight
seal.

5

rubber

washer

General Instructions

5. Replace pop-up drain stopper in drain body, with ‘o’-ring in place,
and align stopper hole with guide and opening.

6. Reinsert rod ball assem-
bly back into drain body and
through hole in drain stopper.

fl ange

drain
stopper

7. Insert pop-up stem through
hole in faucet body. Attach lift
rod to pop-up stem by insert-
ing stem through hole in lift

rod. Reassemble rod guide,
washer and nut, and tighten

fi rmly.

drain
body

rod/ball
assembly

rod guide
washer
and nut

pop-up
stem

9. Make connection to supply
lines.

10. Turn on water supply and
check for leaks.

sink

align hole in
drain stop­per with guide
rod opening
(pointed toward
back wall)

drain
body

8. Adjust pop-up stem to correct height
by opening drain, and sliding lift rod
and rod clip at the same time onto rod/
ball assembly. Readjust lift rod screw
if necessary, hand-tighten.

Side view
faucet and
pop-up
assembly

6

General Instructions

1. Remove no.7, then using
no.8, loosen set screw and
lift off no.6.

2. Unscrew no.12.

3. Unscrew no.11.

4. Adjust no.10 to desired po­sition per below.

Figure 1

Normal factory
set position
allows full mix­ing of hot and
cold water.

Figure 2

Place ring into
this position
to reduce the
amount of hot
water available.
Result: cold
to warm water
only.

Figure 4

Using needle
nose pliers, care­fully lift off the
temperature limit
stop ring from the
cartridge body.
Re-set the ring
onto the body per
Figure 4 or 5.

Figure 3

Place ring into
this position
to reduce the
amount of cold
water available.
Result: warm to
hot water only.

Figure 5

7

B-2730 & B-2731

Single Lever

Faucets

T&S BRASS AND BRONZE WORKS, INC.

A fi rm commitment to application-engineered plumbing products

2 Saddleback Cove, P.O. Box 1088, T & S Brass-Europe

Travelers Rest, SC 29690 ‘De Veenhoeve’
Phone: [phone] Oude Nieuwveenseweg 84
Fax: [phone] CW Nieuwveen

E-mail: [e-mail] The Netherlands