T&S Brass B-2370 Installation Manual

Limited One Year Warranty

T&S warrants to the original purchaser (other
than for purposes of resale) that such product is
free from defects in material and workmanship
for a period of one (1) year from the date of pur­chase. During this one-year warranty period, if
the product is found to be defective, T&S shall,
at its options, repair and/or replace it. To obtain
warranty service, products must be returned to...

T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department

2 Saddleback Cove

Travelers Rest, SC 29690

Shipping, freight, insurance, and other trans­portation charges of the product to T&S and the
return of repaired or replaced product to the
purchaser are the responsibility of the purchaser.
Repair and/or replacement shall be made within
a reasonable time after receipt by T&S of the
returned product. This warranty does not cover
Items which have received secondary finishing
or have been altered or modified after purchase,
or for defects caused by physical abuse to or
misuse of the product, or shipment of the prod­ucts.

Any express warranty not provided herein,
and any remedy for Breach of Contract which
might arise, is hereby excluded and disclaimed.
Any implied warranties of merchantability or fit­ness for a particular purpose are limited to one
year in duration. Under no circumstances shall
T&S be liable for loss of use or any special con­sequential costs, expenses or damages.

Some states do not allow limitations on how
long and implied warranty lasts or the exclusion
or limitation of incidental or consequential dam­ages, so the above limitations or exclusions may
not apply to you. Specific rights under this war­ranty and other rights vary from state to state.

P/N: 098-009758-45 Rev. 1

Date: 980626

Drawn: CW

Checked: MAB 10-16-98

Approved: MW 10-15-98

Installation and

Maintenance

Instructions

ROTOFLEX™
PRE-RINSE UNIT

B-2370 and B-2371

Deutsch: Installations- und

Wartungsanleitungen

Español: la Instalación y las

Instrucciones de
Mantenimiento

Français: les Instructions

d’Installation et
d’Entretien

Exploded View

LfL3LL3L 3LfL3fLffLL3LLLLLL3LLfLL LL L L 3 f

f33 f3Lf3 f3 3f 3 L3LL3 L3 33 3f 3 fLf f3f33ff3f

ffLff ff ff f LfLLf Lf f3 ff f 3 L 3 f33 3 3f Lf 3f 3L LL f

1
RIFF6whDISP,((``$CCDRAvrsn

33L33 33f33f3ff33333L3L33L3fL3 3L 3 3f3fff3fL3f 3fff3fffff

f3 ffL fLf3LffLf fL f f f 33 L3 f fff f L L fLL L 3 L L3

LLL L3L33Lf3L fLLfL fL Lf L LLLLL LL L3 Lf L

3 L3 3 f 3f ff 3 L L 3L fL L

L 3 33 f3 f Lf f f L LL L 3 f

Cl3f3L3 3f3fff3LL3LfL L 333f3

L 333f3 fLf f f LLL L 3 f 3L3 333333

Apply #111 Grease to O-Rings

Before Assembly

Knuckle Assembly

* Some items are listed for instructional purposes

and may not be sold as separate parts.

Part Number Guide

Pre-Rinse Unit 'ROTOFLEX™'

Asm, Base Faucet (B-2370) 002824-40

Asm, Base Faucet (B-2371) 002832-40
1 Asm, Riser 29" 010179-40
2 Riser, Plated *
3 Collar, 2-Piece *
4 Label, "DO NOT ADJUST" *
5 Washer *
6 Collar, Connecting Arm *
7 Screw, Cap 000941-45
8 Cap, Swivel Valve *
9 O-Ring *

10 Bearing, Lower Swivel Valve *
11 Quad-Ring 11/16 ID *
12 Bearing Flange *
13 Spring 000889-45
14 Pipe End, Swivel Valve *
15 Retaining Ring *
16 O-Ring, Cylinder 001065-45
17 Bearing, Top Swivel Valve *
18 Retaining Ring, Cresent Type *
19 Cylinder, Swivel Valve *
20 Cap, Cylinder 3/8 NPT *
21 Asm, Upper Arm 010180-40
22 Nipple 3/8" x 18" 000369-40
23 Asm, Knuckle *
24 Asm, Knuckle - Bushed *
25 O'-Ring, Knuckle Joint 001060-45
26 Retaining Snap-Ring *
27 Pin, Clevis *
28 Connecting Arm *
29 Adapter 3/8 Male x 3/4-14 Male 000545-25
30 Asm, Flex Hose w/ Fan-Jet B-0020-HC
31 Washer, #27 001014-45
32 Asm, Flex S/S Hose B-0020-H
33 Fan-Jet Spray Head 005939-40
34 Asm, Wall Bracket B-0109-01
35 Asm, Clamp *
36 Screw, Clamp 000914-45
37 Clamp, Front 000631-40
38 Clamp, Back 000636-40
39 Nipple, 6" 000346-40
40 Screw, Wall Mount 000915-45
41 Set Screw, Rod End 001584-45
42 Body, Wall Bracket 000064-40

See page 16 for knuckle rebuild and total rebuild parts kits.

General Instructions

Installation:

See separate instructions for
installation of base faucet into deck
or wall.

1. Shut off water supply and drain
lines. Apply Teflon Tape or pipe joint
compound to threads on bottom end
of no.2.

2. Insert a flat-blade screwdriver into
no.14, tighten no.2 firmly into the
base faucet.

Caution: Do not over tighten.

Internal parts are brass and may

become damaged from over-

tightening.

3. Apply Teflon Tape
to threaded no.20,
attach no. 23.

4. Attach no.28 to
no.6 using no.7.

28

23

20

6. Install no.34 after the entire unit is
assembled. Fit no.34 on no.2 in the
position shown below. Cut off any
excess no.39 if necessary, and mount
no.42 to wall using no.40, tighten
no.41 after installation is complete.

2

39

36

42

41

40

wall

7. For maximum stability and
efficiency, install no.34 about 1”
[2.5cm] maximum from no.3.

34

7

3

24

31

32

29

6

2

faucet body

5. Attach no.29 to
no.24, make sure no.31
is in place, then attach
no.32 to no.29.

1” [2.5cm] max.

Repair Kits:______________

Two repair kits are available for the
Rotoflex Pre-Rinse unit. See chart
on page 16 for parts included in
each kit and reference numbers
from parts list on page 3.

General Instructions

Servicing the Rotoflex™:

Note: Refer to illustration on page 2 when following these directions for
servicing this unit.

Complete rebuild kit - Upper Arm Repair - 010188-45

1. Remove the two no.7 from no.28.

2. Hold top of no.19 while loosening no.8 with a wrench. Remove no.8.

3. Carefully lift no.21 from no.1.

4. Use retaining ring pliers to remove and discard no.26 from
no.23 and no.24 on no.21.

5. Slide the knuckle off
the shaft.(Shown right)
Remove no.25 from shaft
and discard. Clean and
inspect parts for damage.

26

25
(apply #111
grease)

If light scratches exist, use
a fine cloth to remove scratches,
if deep scoring exist, parts must be replaced.

6. Apply a thin coat of #111 grease to shaft. Assemble new
set of no.25 onto shaft and apply #111 grease to no.25.

7. Replace knuckles onto shaft and assemble two new
no.26. Set no.21 aside.

Riser Assembly Repair: Rotoflex™

1. Loosen no.36 of no.34 assembly.

2. Using a flat-blade
screwdriver at top of no.2,
unscrew and disassemble
no.2 from the base faucet.

3. Remove no.4 from no.3 and
discard. Loosen no.7 on no.6.

4. Carefully slide all components from no.2.

Upper End - Riser Assembly Repair

5. Remove no.15 and no.18 from upper end of no.1,
remove no.5, no.17 and no.16.

36

shaft
(apply
#111
grease)

knuckle

21, 23, 24

34

28

20

19

15

5

14

12
13

12
11
10

8
5

6
7

5
4

3

1, 2

18
17
16

6. Clean and inspect no.2 and no.13 for damage and replace if necessary.

7. Slide no.5 onto no.14 end of no.2 and secure with no.15.