T&S Brass B-0123 Installation Manual

PRE-RINSE UNIT

B-0123 Series

(B-0123-B, Pre-Rinse Unit w/Wall Bracket)

Installation and

Maintenance

Instructions

Limited One Year Warranty

T&S warrants to the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of one (1) year from the date of purchase. During this one-year warranty period, if the product is found to be defective, T&S shall, at its option, repair and/or replace it. To obtain

warranty service, products must be returned to.....

T&S Brass and Bronze Works, Inc. Attn: Warranty Repair Department 2 Saddleback Cove Travelers Rest, SC 29690

Shipping, freight, insurance, and other transportation charges of the product to T&S and the return of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/or replacement shall be made within a reasonable time after receipt by T&S of the returned product. This warranty does not cover items which have received secondary  nishing or have been altered or modi ed af ter purchase, or for defects caused by physical abuse to or misuse of the product, or shipment of the products. Any express warranty not provided herein, and any remedy for Breach of Contract which might arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or  tness for a particular purpose are limited to one year in duration. Under no circumstance shall T&S be liable for loss of use or any special consequential cost, expenses or damages. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Speci c rights under this warranty and other rights vary from state to state.

Before starting the installation, be sure to  ush supply lines and shut o water supply. Cierre la fuente principal de agua y desagüe las tuberias. Avant de commencer l’installation, coupez l’alimentation d’eau et purgez la tuyauterie. Wasser abstellen und Wasserleitungen entleeren.

Step 1: Apply plumber’s putty to underside of inlets and plumber’s tape to inlet threads. Line up water supply lines and couplings, attach and tighten with wrench.

Step 3: Make sure that the EasyInstall® locking washer is seated properly inside the faucet body.

Step 2: Apply plumber’s tape to top of riser threads and attach to spring assembly. Tighten with wrench.

Step 4: Grab riser assembly and lower the EasyInstall® end tting into faucet body. Press down until the end tting “pops” in.

P/N:

DATE:

DRAWN:

CHECKED:

APPROVED:

098-014496-45 REV. 4 10-26-10 TEH JRM 11-03-10 JHB 11-09-10

Step 5: Lock the EasyInstall® locking nut in place and tighten with wrench.

Base Faucet Assembly

Faucet Assembly

Asm, Spindle - Hot Hot Cartridge Only

Asm, Spindle - Cold

Cold Cartridge Only 41 42

4 5 6 7 8 9

Cerama Cartridge w/ Check Valve, RTC

Cerama Cartridge w/ Check Valve, LTC Handle, Lever - Blank Screw, Handle Index, Button - Hot (Red) Index, Button - Cold (Blue) Washer Asm, Coupling Flange Lock Washer, EZ-Install

Riser Assembly

Riser Assembly, 24”

Nipple, 3/8” x 24”

Swivel Assembly

Swivel Piece

14 15 43

O-Ring, Swivel Piece Asm, Finger Hook & Screw

Wall Bracket, 6” (add -B to model no. for wall bracket)

Pre-Rinse Unit

Pre-Rinse Assembly

Spring, Body

Spring, Overhead

Asm, Flex Stainless Steel Hose

Asm, Spray Valve

Spray Valve Assembly

Asm, Hold Down Ring & Washer

Washer

Ring, Hold Down

Body, Spray Valve (no handle)

Handle

Nut, Handle

Screw, Handle

Nipple

Cup, Spray

Ring, Sprayhead

Sprayface

Screw, Sprayface

Bonnet Assembly

Asm, Bonnet

Stem

Washer, Seat

Washer, Bonnet Binding

Bonnet

Washer, Bonnet Brass

Stem, Packing

Spring, Bonnet

Push Button

Grease Pack (O-Ring Lubricant)

* Parts included in B-10K parts kit

014208-40 002712-40 012443-40 002711-40 012442-40 011311-25 011312-25 001638-45 000922-45 001661-45 001660-45 001019-45 00AA 014200-45

000372-40 EZ-K N/A 001065-45 004R B-0109-01

000821-40 000888-45 B-0044-H B-0107

010476-45 000907-45 000065-40 001120-45 003198-45 003199-45 000694-40 000019-40 007861-45 001121-45 000913-45

002856-40 009306-20 012915-45 001040-45 000608-25 000974-45 001100-45 000895-45 000753-25 012665-45

3839

Set Screws (2)

Wall Bracket Installation:

Clamp Screws (2)

Fasten wall  ange to wall using wall mount screws1. Place 2-piece clamp assembly around riser and tighten 2. clamp screws securely. Tighten set screws securely.3.

323334353637