T&S Brass 5F-1SLX00 Installation Manual

Installation and
Installation and
Maintenance Instructions
EQUIP 4” & 8” DECK-MOUNT FAUCETS AND PRE-RINSE UNITS
Limited One Year Warranty
Equip warrants the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of one (1) year from the date of purchase. During this warranty period, if the product is found to be defective, equip shall, at its option, repair and/or replace it. To obtain warranty service, products
must be returned to:
Equip Foodservice Accessories Attn: Warranty Repair Department P.O. Box 1088, 2 Saddleback Cove Travelers Rest, SC 29690
Shipping, freight, insurance, and other transportation charges of the product to equip and the return of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/or replacement shall be made within a reasonable time after receipt by Equip of the returned product. This warranty does not cover items which have received secondary finishing or have been altered or modified after purchase, or for defects caused by physical abuse to or misuse of the product, or shipment of the products.
Any express warranty not provided herein, and any remedy for Breach of Contract which might arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or fitness for a particular purpose are limited to one year in duration. Under no circumstances shall Equip be liable for loss of use or any special consequential costs, expenses or damages. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Specific rights under this warranty and other rights vary from state to state.
Attention California Residents:
“WARNING: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm.”
P/N: 098-013851-45 Rev.3 Date: 01-15-16 Drawn: TEH Checked: DMH 02-09-16 Approved: JHB 02-23-16
Español:
Instrucciones de instalación y mantenimiento
Français:
Instructions pour l’installation et la maintenance
Deutsch:
Installations- und Wartungsanleitungen
中文:
安装与维护说明
Instructions
STEP 1
B-0425-M 1/2”
NPT Supply
Nipple Kit (2)
STEP 12
STEP 2
STEP 3
deck or sink
STEP 12
2
Instructions
Note: If unit is equipped with a rigid or swivel spout/gooseneck, install spout/ gooseneck  rst.
Rigid Gooseneck Installation:
1. Apply Te on tape, Loctite, or pipe joint compound to threads of gooseneck. Thread gooseneck into outlet hole of body until joint is secure and gooseneck faces desired direction.
Swing Nozzle/ Swivel Gooseneck Installation:
Note: Silicon grease is applied to the interior swivel cavity of the body prior to shipment. No additional grease is required.
2. Remove plastic cap from body outlet.
3. Insert nozzle/gooseneck into body cavity.
4. Tighten swivel lock nut using 1 5/16” wrench.
Faucet Body Installation:
5. Flush debris from water lines then shut o water supply.
6. Drill two holes, approximately 1” to 1 1/4” diameter, in deck or sink where faucet body is to be installed. Holes must be 4” or 8” between centers, as applicable.
7. Remove washers and nuts from B-0425-M supply nipple kits, or similar ½” NPT inlets, and apply Te on tape or thread sealant to the threads on one end of the nipples. Thread this end into the inlet hole of the faucet  ange until the joints are secure.
8. Apply plumbers putty to faucet  ange mounting surfaces and insert the supply nipples though the holes in the deck or sink.
9. Secure faucet in place with supply nipple kit washers and nuts.
10. Connect water supplies to nipples.
Pre-Rinse Installation:
11. After installation of the faucet body per steps 5 through 10, apply Te on
tape, Loctite, or pipe thread compound on the bottom of the riser. Slide  nger hook onto riser before riser installation. Thread riser into outlet hole of faucet body until joint is secured.
12. Install wall bracket and  nger hook, tightening all fasteners securely.
13. Rotate spring and hose assembly until they face desired direction.
14. Turn on water supplies and check for leaks.
3
Instrucciones
PASO 1
PASO 2
B-0425-M Kit de
empalme de suministro
de ½ pulg. NPT (2)
PASO 12
PASO 3
Cubierta o lavabo
PASO 12
4
Loading...
+ 8 hidden pages