TruVue 75369 User Manual

75369

Introduction and Package Contents

Introduction

Congratulations on your purchase. You can expect only the sharpest and most brilliant colour images from this monitor. Featuring easy to use OSD controls and built in speakers, you will find this monitor both easy to use and a pleasure to look at.

Package Contents

 One LCD Monitor  12V DC Adapter  Power cord  D-Sub 15-pin VGA connector Cable  User's Guide

Hardware Installation

The following sections in this guide give clear, step-by-step descriptions of the installation process and explain how to use the monitor for optimum results.

Please pay attention to the Regulations and Warnings Section of

this user’s manual before setting up the display monitor. Failure

to do so may inadvertently result in personal injuries or machine damage.

19” rear connections

Specifications (75369)

Size

19”

Composite Output

(BNC) x 2

Composite Input

(BNC) x 2

Single Connector

(VGA) x 1, (RCA) x 2 (PC Audio) x 1, (HDMI) x 1

Speaker

1.5W x 2

Display Mode

Video 1/ Video 2/ PC/ HDMI

AC power

AC 100~240V 50/60Hz

Temperature

Operation: 0°~40°C(32° ~104°F) , Storage: -10°~60°C(14° ~140°F)

Power Consumption

35W Max.

OSD Control

Picture Mode, Contrast, Brightness, Colour, Tint, Sharpness,

Colour Temp, DNR

OSD Languages

English, German, French, Italian, Spanish, Russian, Turkish,

Polish, Dutch, Czech

Auto Adjustment

Yes (Only for VGA mode)

De-interlace

Yes

Wall mount

VESA 75mmx75mm

Accessories

Adapter, Power code, Manual, VGA cable

Safety

FCC, CE, ROHS

Tilt

-5°~15°

Humidity

10％~90％

Monitor scan

Microprocessor controlled

Pixel pitch

0.294x0.294mm

Pixel format

1280x1024

Response time

5ms

Colour depth

16.7 Million Colors

Viewing angle

Vertical -80°~80°

Horizontal -80°~80°

Display area

(H x V mm)

376.3x301.06

Dimension

(W x H x D mm)

424 x 415 x 165

Weight

(monitor only)

3.8Kgs (8.4 lbs)

Dimensions;

VGA Timing

Item

Resolution

H Freq.(kHz)

V Freq.(Hz)

640x400@70

31.460

70.080

640x480@60

31.469

59.940

640x480@72

37.861

72.809

640x480@75

37.500

75.000

720x400@70

31.460

70.080

800x600@56

35.156

56.250

800x600@60

37.879

60.317

800x600@72

48.077

72.188

800x600@75

46.875

75.000

1024x768@60

48.363

60.004

1024x768@70

56.476

70.069

1024x768@75

60.023

75.029

1280x1024@60

63.981

60.020

1280x1024@75

79.976

75.025

Remark: The timings with presetting are recommended. Users have to adjust the timing manually, if it is not included in the presetting list

Select

Auto Power

Monitor and OSD Control

The LCD color monitor has a simple control layout for controlling the monitor and OSD (On Screen Display) functions. The table below summarizes the control keys and their related functions.

6-Key feature

Keys

Function Description

Power

Toggle the display between standby mode and on.

(Press “Power” and waiting 6 sec., monitor will be display )

A / Auto

Automatically adjusts H-Position, V-Position, Pixel Clock and Phase for an optimal image in PC mode only.

Switch setting item. Increase the value of the chose item.

Switch setting item. Decrease the value of the chose item.

S / Select

Switch mode “PC”, ”AV1”, ”AV2” , “HDMI”.

M / Menu

Enter the main menu of the on-screen display (OSD).

LED Status Display

The following table describes the various power states of the LCD monitor as represented by different LED color.

Power State

LED Color

Green

Standby

Red

No power

Blank

OSD Menu

Picture Mode

1. Picture Mode

Press -/ OR +/ to select the picture mode “User, Standard, Movie, Vivid ”

2. Contrast

This is used to set the brightness of the screen. Press -/ OR +/ to adjust the parameter.

3. Brightness

This is used to adjust the image contrast. Press -/ OR +/ to adjust the parameter.

4. Tint

This is used to adjust the image Tint. Press -/ OR +/ to adjust the parameter.

5. Saturation

This is used to adjust the image saturation. Press -/ OR +/ to adjust the parameter.

6. Sharpness

Adjust the sharpness. It makes the image become soft. Press -/ OR +/ to adjust the parameter.

7. Color Temp.

Press -/ OR +/ to adjust the color tones. “ Cool , Warm , Normal “

8. DNR

Press -/ OR +/ to adjust the noise reduction. “High , Low, Off, Mid “

Note: VGA Mode: Contrast, Brightness, Color Temp., Auto Adjust.

Sound Mode

1. Volume

Press -/ OR +/ to adjust volume level.

2. Mute

Press -/ OR +/ to select sound “ Off, On ”.

OSD Control Function List

Setting Mode

1. Language

Press -/ OR +/ to select language.

2. H. Position

Move the display picture left or right. Press -/ OR +/ to adjust the parameter.

3. H Zoom

Adjust the H-size of the display picture Press -/ OR +/ to adjust the parameter.

4. V Position

Move the display picture up or down. Press -/ OR +/ to adjust the parameter.

5. V Zoom

Adjust the V-size of the display picture Press -/ OR +/ to adjust the parameter.

6. Clock

Press “ ” OR “ ” to adjust the parameter.

7. Phase

Press “ ” OR “ ” to adjust the parameter.

8. Scale Mode

Adjust the V-size of the display picture Press -/ OR +/ to adjust “ Full, 16:9 ”.

9. Reset

Recall Default value.

Note: “ Clock” and “Phase ” setting only in VGA Mode

PIP/POP Setup Mode

1. Multi Window

Press -/ OR +/ to select “PIP, POP, Off ” mode.

2. Sub Source

Press -/ OR +/ to select “AV, VGA” mode.

3. Size

Adjust the size of Sub Source window. Press -/ OR +/ to select “Large, Small ”

4. Position

Move the position of Sub Source window. Press -/ OR +/ to select “L U, R D, R U, L R” position.

5. Border Color

Choose the border color of Sub Source window. Press -/ OR +/ to select “Black, Blue” color.

6. Sound Source

Press -/ OR +/ to select “Main, Sub” mode.

7. Swap

Press S/Select to Swap the Source of Main and Sub.

Note:

1. AV1 and AV2 , HDMI and VGA cannot be displayed at the same time on the

monitor in PIP / POP mode.

2. If POP mode is selected both images are scaled to fit the screen.

VGA Mode

AV/HDMI Mode

Caring for your LCD Monitor

The LCD color monitor is a sensitive piece of electronic equipment. Proper care can prevent accidentally damaging the LCD panel or the monitor itself. By following these guidelines you can ensure many years of trouble free use.

1. The LCD monitor's plastic casing and LCD glass panel can be

cleaned with a soft, lint-free cloth. Never use scrub pads or

other cleaning materials with abrasive surfaces to clean your LCD monitor!

a. A slightly damp cloth or newspaper may be used to

clean the glass plate of fingerprints or smudges.

b. For the plastic case, a mild detergent may be used to

clean the surface. However, you should ensure not to use too much detergent or water as this could leak into the interior of the casing.

2. Do NOT use cleaning fluids based on alcohol, methylated

spirit, or ammonia. The glass plate has a hard surface coating to prevent scratches. However, the use of strong chemical cleaning agents may damage this coating. Use only a mild soap or detergent and water or specially formulated cleaners made for cleaning glass panels.

3. Avoid direct contact with water or other liquids. Never use

the LCD monitor in or around areas where water may pose a potential hazard to normal operation.

4. Only use the LCD monitor indoors, and avoid monitor contact

with oil, vapor, steam, moisture and dust. The LCD monitor should be used in a clean and low humidity environment.

5. Keep the LCD monitor away from heaters or other heat

sources such as lighting equipment or direct sunlight.

6. Keep the LCD monitor away from sharp object to touch the

screen like fingernail and pencil.

WARNING: Any unauthorized modification to this equipment could result in the revocation of the authorization to operate the equipment and void the product warranty.

Caring for Your LCD Monitor

Frequently Asked Questions

Power button does not respond

 Check the power cord to ensure that it is securely plugged

into the monitor base and also into the electrical outlet.

 Ensure there is electrical power coming from the AC outlet.

Use another device to check for power.

 Unplug the power cord of the monitor from the AC outlet,

wait a few minutes, then to plug the power cord into the AC outlet again. This will reset the monitor and power supply.

No image on the screen

 Ensure that the DB-15 signal cable is properly connected to

the display card/computer.

 Check the DB-15 signal cable connector on both ends for

bent or pushed-in pins.

 The display card should be properly seated in its card slot.  Ensure that the computer's power switch is ON.  Ensure that the monitor's power switch is ON.

 Unplug the power cord of the monitor from the AC outlet,

wait a few minutes, then to plug the power cord into the AC outlet again. This will reset the monitor and power supply.

Power LED is RED (with no image on the screen)

 Check the DB-15 signal cable to ensure that it is properly

attached to the graphics display card.

 Check the DB-15 signal cable on both ends for bent or

pushed-in pins.

 Make sure the computer is not in a power-saving mode

(move the mouse or press a key on the keyboard).

No sound coming from the audio speakers

 The audio cable should be connected to the lineout on the

audio card and the line-in on the monitor. Ensure that the audio cable is properly connected.

 Inspect the audio cable for any apparent damage. Double

check by switching to another audio cable to see if the audio works.

Regulations and Maintenance

FCC compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generation, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and

receiver.

 Connect the equipment to an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician

for help.

Precautions

＊ Read all of these instructions and save them for later use. ＊ Follow all warnings and instructions on the product. ＊ Product

- Do not cover or block the vent holes in the case.

- Do not insert sharp objects or spill liquid into the LCD monitor through cabinet

slots. They may cause accident fire, electric shock or failure.

- Disconnect the power plug from the AC outlet if you will not use it for an

indefinite period of time.

- Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage potentials or other risks.

- Do not touch the screen directly with your fingers. You may damage the screen,

and oil from your skin is difficult to move.

- Do not apply pressure to the screen. The LCD is very delicate.

＊ Power

- Use the type of power indicated on the marking label.

＊ Plugs

- Do not remove any of the prongs of the monitor’s three-pronged power plug.

- Disconnect the power plug from the AC outlet under following conditions:

◎ If you will not use it for an indefinite period time. ◎ When the power cord or plug is damaged or frayed. ◎ If the product does not operate normally when the operation instructions are

followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

◎ If the product has been dropped or the cabinet has been damaged. ◎ If the product exhibits a distinct change in performance, indicate a need for

service.

＊ Power and extension cords

- Do not allow anything to rest on the power cord.

- Do not locate this product where persons will walk on her cord.

- Use the proper power cord with correct attachment plug type. If the power

source is 120 V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country’s safety regulations, such as VDE for Germany.

- Do not overload wall outlets or power cords. Ensure that the total of all units

plugged into the wall outlet does not exceed 10 amperes.

- Ensure that the total ampere rating of all units plugged into the extension cord is

not over the cord’s rating.

- If the power supply cord, which came with your monitor, is to be connected to

the PC instead of the wall outlet, this equipment is to be used with UL/TUV approved computers with receptacle rated 100~240V AC, 50/60Hz,

2.0A(minimum).

＊ Environment

- Place the monitor on a flat and leveled surface.

- Place the monitor in a well-ventilated place.

- Keep the monitor away from:

Extremely hot, cold or humid places, places directly under sunlight, dusty surroundings,

equipment that generate strong magnetic fields.

TruVue 75369 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual