User instructions
VA20HD, VA55HD, VA55IND and VA75IND
Commercial wet/dry vacuum cleaners
CAUTION - READ THESE INSTRUCTIONS BEFORE USING THE MACHINE
03-8112-0000 Iss.3 07/08
http://www.truvox.com/Products/Vacuums/Valet_Aqua
Contents
Page
1 Product information ......................................................................................... 3
1.1 Important safety advice .......................................................................................... 3
1.2 Guidelines for the operator .................................................................................. 3
1.3 Transporting the machine ...................................................................................... 3
2 Preparing for use .................................................................................................. 4
2.1 Electrical connection ............................................................................................... 4
2.2 Wet operation........................................................................................................... 4
2.3 Dry operation............................................................................................................ 4
3 Controls ........................................................................................................................ 4
4 Operation .................................................................................................................... 4
5 Storage .......................................................................................................................... 5
6 Maintenance ............................................................................................................. 5
7 After sales service ............................................................................................... 5
8 Guarantee ................................................................................................................... 5
9 Waste Electronic & Electrical Equipment ................................... 6
10 Technical specification ..................................................................................... 6
11 Accessories ................................................................................................................ 7
12 Fault diagnosis ........................................................................................................ 7
13 Declaration of conformity ........................................................................... 8
IMPORTANT
READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE
1 Product information
These commercial wet or dry vacuum cleaners
are designed for the collection of dust or liquids
in indoor areas. They should not be used in
outdoor areas.
The following instructions contain important
information about the machines and safety
advice for the operator.
Equipment must be operated, serviced and
maintained in accordance with the
manufacturer’s instructions.
If in doubt contact the supplier of your
machine.
These instructions are valid for the following
models.
VA20HD VA55HD VA55IND, VA55IND/110
VA75IND, VA75IND/110
1.1 Important Safety Advice
When using electrical equipment basic safety
precautions should be followed including the
following.
• Read all instructions carefully before use.
• Keep children and unauthorised persons
away from the machine when in use.
• Do not leave the machine connected to the
electricity supply when not in use, always
remove the plug from the socket-outlet.
• Do not operate switches or touch the mains
plug with wet hands as this may cause electric
shock.
• Switch off the machine before removing the
plug.
• When unplugging pull the plug, not the supply
cord.
• Do not operate the machine with a damaged
supply cord or plug, or after the machine
malfunctions or is damaged in any way.
Contact an authorised Service Agent for
repair or adjustment.
• The plug of the power supply cord must be
removed from the socket-outlet before
commencing cleaning of the machine or
undertaking maintenance operations.
•
The power supply cord must be regularly
inspected for signs of damage. If the power
supply cord is damaged, it has to be replaced.
•
Do not use where hazardous dust is
present.
•
Do not use in an explosive atmosphere.
•
Do not pick up oil or other flammable
material.
•
Take care when using a machine near the top
of stairs to avoid overbalancing.
1.2 Guidelines for the operator
• Only use the machine on firm level surfaces.
• Operators must be fully trained in the use of
the machine in accordance with these
instructions, able to perform user
maintenance and the correct selection of
accessories, i.e. filters, hoses etc.
• Do not leave machine running unattended
• Operators should be physically capable to
manoeuvre, transport and operate the
machines.
• Operators should be able to recognise
unusual operation of the machine and report
any problems.
• Wear suitable footwear to avoid slipping.
• Wear suitable clothing to keep dry and
warm.
• Where possible implement job rotation
and adequate rest periods to avoid
continuous use of the same muscles.
• Do not smoke when using the machine.
• WARNING – should foam/liquid emit
from the machine exhaust switch off
immediately and refer to instructions
for operating the machine.
• CAUTION – This machine is for
indoors use only and should not be used
or stored outdoors or in wet conditions.
1.3 Transporting the machine
When transporting a machine ensure that all
components, tanks and removable parts are
securely fastened and that the supply cord and
plug are not trailing. Detach hose and wand
from machine where applicable.
Do not lift or transport the machine whilst
containing liquid as this would add considerably
to the weight.
Take extreme care when moving a machine up
or down steps or stairs.
Caution – VA55HD, VA55IND and
VA75IND machines are large and heavy.
Do not attempt to lift these machines
without assistance. Incorrect lifting
techniques may result in personal injury.
2 Preparing for use
3 Controls
2.1 Electrical connection
Before connecting the machine to the power
supply, check that your supply voltage
corresponds with that marked on the rating
label on the handle of the machine.
The power supply cord plus any extension leads
should not exceed 30m in total. The crosssection of any extension cable wiring must be at
least 2,5 mm².
UK only
The supply cord for 230v models is fitted with a plug
containing a 13 amp fuse. Should the fuse require
replacement it must only be replaced by a 13 amp
fuse conforming to BS1362, and the fuse cover must
be refitted. If the fuse cover is lost the plug must
not be used until the correct replacement cover is
fitted.
IMPORTANT - If the supply cord is damaged,
it must only be replaced by a suitable cord
available from the manufacturer or an
authorised service agent.
WARNING - VA55HD, VA7555IND &
VA75 IND MUST BE EARTHED. VA20HD IS
DOUBLE INSULATED.
2.2 Wet operation
For the VA55HD, VA55IND and VA75IND the
pleated paper filter must be removed for wet
recovery. Push the metal ping counter
clockwise to release the filter. Remove the
pleated paper filter. (See fig below)
The primary filter (cloth filter on frame) and
float valve assembly must be in place.
The ON/OFF motor switch is located on the
motor cover of all machines. The VA75IND
features two motors, each controlled by a
separate switch.
4 Operation
• Check that the correct filters are in place:
• Wet use – remove pleated paper filter.
• Dry use – ensure pleated paper filter is in
place
• For both wet or dry use ensure the large
primary filter is in place
• Reposition motor head on container and
fasten toggle clamps.
• Connect hose to machine inlet, ensuring that
clip engages fully. Add extension tubes and
select suitable floor tool for your cleaning
operation
• Fully unwind the supply cord and plug into a
convenient socket outlet. Switch machine on.
• Pass tool backwards and forwards over area
to be cleaned. To reduce suction when
necessary move slide control on wand.
• When using the machine for dry collection
regularly check that vacuum is not full.
• When using the machine for wet pick-up a
high liquid level cut off device (float valve)
operates when the vacuum cleaner is full. This
causes a change in the sound level and an
immediate loss of suction. Switch off
2.3 Dry operation
For the VA55HD, VA55IND and VA75IND
both the primary filter (cloth filter on frame)
and pleated paper filter must be in position for
dry recovery.
immediately and unplug the machine.
Empty the machine
• VA20HD – Remove motor head and hose
and empty liquid from tank.
• VA55HD – Release drain hose from clip.
Remove plug from drain hose end to
drain. When draining is complete replace
hose plug and snap hose back into clips
on tank side.
• VA55IND & VA75IND – these models
have a tip and pour trolley.
• Remove the motor head and take out
the primary filter and frame.
• Unlock the knob (see diagram below)
• Grip the handle with one hand, use one
foot to brace the trolley and lift the
handle on the tank by the other hand to
empty the tank.
5 Storage
• After use check that the machine is empty
then clean and dry the machine. If used for
wet pick up remove motor head and wash out
tank with clean water and dry.
• Thoroughly clean the primary filter, paying
particular attention if machine has been used
to collect stripper, slurries or anything that
could dry to hard crust.
• Wrap supply cord around the handle or
machine body ensuring that the plug is not
trailing on the floor.
• Store the machine in a dry indoor area only.
6 Maintenance
WARNING - Before undertaking
maintenance operations or adjustments
switch off machine and unplug from the
electricity supply.
The machine requires minimum maintenance
apart from the following checks by the
operator.
• Supply cord – Regularly inspect sheath, plug
and cord anchorage for damage or loose
connection.
• Body of the machine – Clean with a damp
cloth.
• Primary filter – clean and dry after each
use. Avoid build-up of collected debris setting
solid on the filter.
• Float valve – clean an ensure float moves
freely
IMPORTANT - Should the machine fail to
operate contact Truvox Customer Service
Department for rapid attention.
7 After sales service
Truvox machines are high quality machines that
have been tested for safety by authorised
technicians. It is always apparent that after
longer working periods, electrical and
mechanical components will show signs of wear
and tear or ageing.
To maintain operational safety and reliability the
following service interval has been defined:
Every year or after 250 hours.
Under extreme or specialised conditions and/or
insufficient maintenance, shorter maintenance
intervals are necessary. Use only original
Truvox spare parts. Use of other spare parts
will invalidate all warranty and liability
claims.
Should you require after sales service please
contact the supplier from whom you purchased
the machine, who will arrange service. Repairs
and servicing of Truvox products should only be
performed by trained staff. Improper repairs
can cause considerable dangers to the user.
Enquire about the Truvox low cost and efficient
Maintenance Contract.
8 Guarantee
Your product is guaranteed for one year from
the date of original purchase, or hire purchase,
against defects in materials or workmanship
during manufacture. Within the guarantee
period we undertake at our discretion, to repair
or replace free of charge to the purchaser, any
part found to be defective, subject to the
following conditions.
CONDITIONS
1. Claims made under the terms of the
guarantee must be supported by the original
invoice/bill of sale issued at the time of sale, or
the machine Serial No.
2. For claims under this guarantee contact the
supplier from whom you purchased the product
who will arrange the appropriate action. Do not
initially return the product as this could result in
transit damage.
3. Neither Truvox nor its distributor shall be
liable for any incidental or consequential loss.
4. This guarantee is governed by the laws of
England.
5. This guarantee does not cover any of the
following:
- Periodic maintenance, and repair or
replacement of parts due to normal wear
and tear.
- Damage caused by accident, misuse or
neglect, or the fitting of other than genuine
Truvox parts.
- Defects in other than genuine Truvox parts,
or repairs, modifications or adjustments
performed by other than a Truvox service
engineer or authorised service agent.
- Costs and risks of transport relating
directly or indirectly to the guarantee of
this product.
- Consumable items such as, brushes, drive
discs, filters and vacuum skirts.
This guarantee does not affect your statutory
rights, or your rights against the supplier arising
from their sales or purchase contract.
Truvox International Limited policy is one of
continual product development and we reserve
the right to alter specifications without prior
notice
9 Waste Electrical & Electronic
Equipment
Do not dispose of electrical appliances as
unsorted municipal waste, use separate
collection facilities.
Contact your local government for information
regarding the collection systems available.
If electrical appliances are disposed of in landfills
or dumps, hazardous substances can leak into
the groundwater and get into the food chain,
damaging your health and well-being.
When replacing old appliances with new once,
the retailer is legally obligated to take back your
old appliance for disposal at least for free of
charge.
10 Technical Specification
Model
Tank material Polyethylene 18 gauge stainless steel
Voltage a.c. V 230 230 230 110 230 110
Frequency Hz 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60
No. of motors 1 1 1 1 2 2
Motor rating (total) W 1200 1200 1200 1200 2400 2400
Capacity – dry L 17 51.1 52.9 52.9 68.1 68.1
Capacity – wet L 18.9 56.8 58.8 58.8 75.7 75.7
Construction class 11 1 1 1 1 1
Protection IP IPX4 IPX4 IPX4 IPX4 IPX4 IPX4
Airflow l/sec 54 54 54 54 90 90
Vacuum kPa 24.9 24.9 24.9 24.9 19.9 19.9
Hose length m 2 3 3 3 3 3
Cable length m 8 8 8 8 8 8
Size (l x w x h) cm 49x39x36 92x39x50 94x53x68 94x53x68 94x61x80 94x61x80
Weight kg 10.4 27.7 23.6 23.6 35.4 35.4
Noise Level (see note 1) dB(A)
1 - Noise levels measured at a distance of 1 metre from machine and 1,6 metres above floor,
Measurements recorded using a hand held meter.
VA20
HD
85 85 85 85 85 85
VA55
HD
VA55
IND
VA55
IND/110
VA75
IND
VA75
IND/110
11 Accessories
Item
Part No.
Usage
Fixed floor nozzle
FM100H
for
VA55HD
Fixed floor nozzle
FM100
for
VA55IND
Fixed floor nozzle
FM200
for
VA75IND
Seal worn
Replace seal
very fine du
st,
IMPORTANT : Genuine accessories are only available from authorised Service Agents or Truvox
Customer Service Dept.
12 Fault diagnosis
The following simple checks may be performed by the operator.
Trouble Reason Remedy
Machine not working. • Lack of voltage/electrical supply. • Check fuse *, supply cord, plug
and socket outlet.
Loss of suction • Tank full.
• Dry filter assembly clogged
• Clogged hose or wand.
• Tank rim is dented
• Loose or broken fan
• Motor not working
• Float not functioning
•
Motor is not running • Broken switch
• Defective power cord
• Defective motor
Dust blowing from unit when
running
• Cloth filter dirty
• Cloth filter is torn
• Cloth filter is not installed
• Empty Tank
• Clean cloth filter
• Remove obstruction
• Replace tank
• Contact supplier
• Contact supplier
• Check to see if float moves freely
or tank is full.
•
• Contact supplier
• Contact supplier
• Contact supplier
• Clean cloth filter.
• Replace filter.
• Install cloth filter, when vacuuming
Water blowing from unit when
running
• Tank is full of liquid
• Sudsy or foamy liquid is being
picked up
• Empty tank.
• Add defoamer to tank
* If the fuse blows several times, the machine should be checked by an authorised Service Agent.
13 Declaration of conformity
EC Declaration of conformity
We, Truvox International Ltd.
Of Third Avenue
Millbrook Trading Estate
Southampton SO15 0LE
England
declare that the machinery
Make : Commercial wet / dry vacuum cleaners
Type : VA HD and VA IND
Model : VA20HD, VA20HD/110, VA55HD, VA55HD/110
VA55IND, VA55IND/110, VA75IND, VA75IND/110
Year of Construction : from 2006
has been manufactured using the following transposed harmonised European Standards and technical
specifications.
BS EN 50081-1, BS EN 55014-1 & 2, BS EN 60335-1 and BS EN 60335-2-69, and is in conformity with:
the Machinery Directive 98/37/EC and subsequent amendments,
the Low Voltage Directive 73/23/EEC and subsequent amendments,
and the EMC Directive 89/336/EEC and subsequent amendments.
Signed in : SOUTHAMPTON, England
on the 1st day of December 2006
Signature :
Name : Malcolm Eneas
Position : New Product Development Manager
Truvox International Limited, Third Avenue, Millbrook, Southampton, Hampshire SO15 0LE England
Tel: +44 (0) 23 8070 2200 Fax: +44 (0) 23 8070 5001
e-mail: truvox@truvox.com Web: www.truvox.com
Loading...