Truvox International Air Mover AM, Air Mover AM/T, Air Mover AM/T/110, Air Mover AM/110 User Instructions

1

User instructions

Air Mover AM and AM/T

Commercial Carpet and Floor Dryers

03-8111-0000 Issue 1 12/09

CAUTION

- READ THESE INSTRUCTIONS BEFORE

USING THE MACHINE

2

Contents

1. Product Information ........................................................................................................................ 3

1.1. Important Safety Advice ..................................................................................................... 3

1.2. Guidelines for the operator ................................................................................................. 3

1.3. Transporting the machine ................................................................................................... 3

2. Preparing for use ........................................................................................................................... 3

2.1. Electrical connection ........................................................................................................... 3

3. Controls .......................................................................................................................................... 4

4. Operation ....................................................................................................................................... 4

5. Storage ........................................................................................................................................... 4

6. Maintenance................................................................................................................................... 4

7. After Sales Service ........................................................................................................................ 4

8. Guarantee ...................................................................................................................................... 4

9 Waste Electrical & Electronic Equipment (WEEE)......................................................................... 5

10 Technical Specification .................................................................................................................. 6

11 Accessories .................................................................................................................................... 6

12 Fault diagnosis ............................................................................................................................... 6

13 Declaration of conformity ............................................................................................................... 7

3

IMPORTANT

READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE

1. Product Information

These machines are designed for drying carpets, hard
floors and other interior areas. They can also be used
to ventilate and cool areas. They should not be used
in outdoor areas. The following instructions contain
important information about the machines and safety
advice for the operator. Equipment must be operated,
serviced and maintained in accordance with the
manufacturer’s instructions. If in doubt contact the

supplier of your machine.

These instructions are valid for the following models.
Air Mover – AM, AM/110, AM/T, AM/T/110

1.1. Important Safety Advice

When using electrical equipment basic safety
precautions should be adhered to including the
following:

• Read all instructions carefully before use.

• Use only as described in this manual.

• Only use manufacturer’s recommended

components and attachments.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use with

any opening blocked; keep free of dust, debris and
anything that may reduce airflow.

• Do not cover machine when in use.

• Keep children and unauthorised persons away from

the machine when in use.

• Do not leave the machine connected to the
electricity supply when not in use, always remove
the plug from the socket-outlet.

• Switch off the machine before removing the plug.

• When unplugging pull the plug, not the supply cord.

• Do not pull or carry by the supply cord. Do not use

cord as a handle, close door on cord or pull cord
around sharp edges or corners.

• Keep cord away from heated surfaces.

• Do not operate the machine with a damaged supply

cord or plug, or after the machine malfunctions or is
damaged in any way. Contact an authorised Service
Agent for repair or adjustment.

• The plug of the power supply cord must be removed
from the socket-outlet before commencing cleaning
of the machine or undertaking maintenance
operations.

• The power supply cord must be regularly inspected
for signs of damage. If the power supply cord is
damaged, it has to be replaced.

• Do not use where hazardous dust is present.

• Do not use near flammable fluids, dusts or vapours.

• Do not use in an explosive atmosphere.

• Take care when using a machine near the top of

stairs to avoid overbalancing.

• Warning: do not stack dryers more than two units
high without tie-downs.

1.2. Guidelines for the operator

• Operators must be fully trained in the use of the
machine in accordance with these instructions, able
to perform user maintenance and the correct
selection of accessories.

• Operators should be physically capable to
manoeuvre, transport and operate the machines.

• Keep machine clean and in good operating
condition.

• Operators should be able to recognise unusual
operation of the machine and report any problems.

• Wear suitable footwear to avoid slipping.

• Wear suitable clothing to keep dry and warm.

• Do not smoke when using the machine.

• CAUTION - For indoor use only. Do not use

outdoors or expose to rain.

1.3. Transporting the machine
CAUTION - THIS MACHINE IS HEAVY

Incorrect lifting techniques may result in personal
injury.
Carry by the handle on top of the machine. AM/T
models feature in-built wheels and telescopic handle
for easy transport.

2. Preparing for use

2.1. Electrical connection

Before connecting the machine to the power supply,
check that your supply voltage corresponds with that
marked on the rating label on the machine.
The power supply cord plus any extension leads
should not exceed 30m in total. The cross-section of
any extension cable wiring must be at least 2,5 mm2.

IMPORTANT - If the supply cord is damaged, it must
only be replaced by a

suitable cord available from the

manufacturer or an authorised service agent.

WARNING -THIS APPLIANCE MUST BE EARTHED

UK only

The supply cord for 230v models is fitted with a
plug containing a 13 amp fuse. Should the fuse
require replacement it must only be replaced by a
13 amp fuse conforming to BS1362, and the fuse
cover must be refitted. If the fuse cover is lost, the
plug must not be used until the correct
replacement cover is fitted.

4

3. Controls

The operating switch for all models is located on the
side (see page 2 for Fig 1, 2 & 4).

Fig 1 – Three speed switch
Rotate switch to select speed

Fig 2 – Cable winder
For tidy cable storage

Fig 4 – Kick stand
Flip stand out to raise nozzle

WARNING – Only use accessories or spares
specifically designed for use with this appliance.
The fitting of other accessories or spares may
affect its performance and safety.

4. Operation

• Select suitable location for dryer.
IMPORTANT – Ensure dryer is in a safe position. Do
not sit dryer in a puddle and make sure it is protected
from drips and splashes.

• Fully unwind the supply cord from the cable winder
and plug into a convenient socket outlet.

• Place the dryer in the desired operating position.

• Horizontal (fig 3) – dry floors and carpets.

• Tilted (fig 4) – dry floor finishes, paint etc.

• Vertical (fig 3) – place against a wall to dry wall and

ceiling following a pipe burst or similar.

• Set the desired speed by turning rotary switch (fig 1)

• Check for proper operation before leaving the unit

unattended. Do not move or carry the dryer when it
is running.

• To stop the machine turn switch to OFF (fig 1).

5. Storage

Always unplug and wipe down and dry the machine
after use. Wrap supply cord around the cable winder
ensuring that the plug is not trailing on the floor.
Store the machine in a dry indoor area only.

6. Maintenance
WARNING - Before undertaking maintenance

operations or adjustments switch off machine and
unplug from the electricity supply.
The machine requires minimum maintenance
apart from the following checks by the operator.

• Supply cord - Regularly inspect sheath, plug and
cord anchorage for damage or loose connection.

• Body of the machine - Clean with a damp cloth.

• Air vents - Check for dust accumulation around the

air inlet and outlet vents and clean if necessary.

• Blocked vents will cause the motor to overheat, and
may lead to premature failure. Warranty claims for
this type of damage will not be accepted

• Motor overload cut-out - All machines are fitted
with

an automatic reset motor overload cut-out. The cut­out will operate to protect the motor from overheating
by switching the machine off. Should the cut-out
operate it will reset automatically when the motor has
cooled sufficiently, usually after 15 - 30 minutes.
IMPORTANT - Should the machine fail to operate
contact Truvox Customer Service Department for
rapid attention.

7. After Sales Service

Truvox machines are high quality machines that have
been tested for safety by authorised technicians. It is
always apparent that after longer working periods,
electrical and mechanical components will show signs
of wear and tear or ageing.
To maintain operational safety and reliability the
following service interval has been defined: Every
year or after 250 hours.
Under extreme or specialised conditions and/or
insufficient maintenance, shorter maintenance
intervals are necessary. Use only original Truvox
spare parts. Use of other spare parts will invalidate all
warranty and liability claims!
Should you require after sales service please contact
the supplier from whom you purchased the machine,
who will arrange service. Repairs and servicing of
Truvox products should only be performed by trained
staff. Improper repairs can cause considerable
dangers to the user.

Enquire about the Truvox low cost and efficient
Maintenance Contract.

8. Guarantee

Your product is guaranteed for one year from the date
of original purchase, or hire purchase, against defects
in materials or workmanship during manufacture.
Within the guarantee period we undertake at our
discretion, to repair or replace free of charge to the
purchaser, any part found to be defective, subject to
the following conditions.

CONDITIONS

1. Claims made under the terms of the guarantee
must be supported by the original invoice/bill of
sale issued at the time of sale, or the machine
Serial No.

2. For claims under this guarantee contact the
supplier from whom you purchased the product
who will arrange the appropriate action. Do not
initially return the product as this could result in
transit damage.

3. Neither Truvox nor its distributor shall be liable for
any incidental or consequential loss.

4. This guarantee is governed by the laws of
England.

5. This guarantee does not cover any of the
following:

- Periodic maintenance, and repair or replacement
of parts due to normal wear and tear.

- Damage caused by accident, misuse or neglect,
or the fitting of other than genuine Truvox parts.

5

- Defects in other than genuine Truvox parts, or
repairs, modifications or adjustments performed
by other than a Truvox service engineer or
authorised service agent.

- Costs and risks of transport relating directly or
indirectly to the guarantee of this product.

- Consumable items such as, brushes, drive discs,
filters and vacuum skirts.

This guarantee does not affect your statutory rights, or
your rights against the supplier arising from their sales
or purchase contract.

Truvox International Limited policy is one of continual
product development and we reserve the right to alter
specifications without prior notice

9 Waste Electrical & Electronic Equipment

(WEEE)

Do not dispose of this device with unsorted waste.
Improper disposal may be harmful to the environment
and human health.

Please refer to your local waste authority for
information on return and collection systems in your
area.

6

10 Technical Specification

Model

Air Mover

Air Mover with trolley

Product Code

AM AM/110 AM/T AM/T/110

Voltage

v 230 110 230 110

Frequency

Hz 50/60 50/60 50/60 50/60

Rated power

W 247 575 247 575

Construction class

Earthed

Earthed Earthed Earthed

Protection

IP IP22

IP22 IP22 IP22

Maximum airflow

cfm 1540 1540 1540 1540

m³/h 2600 2600 2600 2600

Noise level 1

db(A)

80 80 80 80

Speeds

3 3 3 3

Thermal overload

   

Kickstand

   

Telescopic handle and

 

High visibility mains lead

m 6 6 6 6

Size (hwl)

cm

157.5119.5162.5 157.5119.5162.5 157.5119.5162.5 157.5119.5162.5

Weight

kg 15 15 15 15

Warranty

years

1 year

1. Noise levels measured at a distance of 1 metre from machine and 1,6 metres above floor
Measurements recorded using a hand held meter

11 Accessories

Item Part no. Usage

Carpet clamp kit PD100

Clamp to hold carpet on machine.
Enables carpet to be dried from
underneath.

IMPORTANT - Genuine accessories are only available from authorised Service Agents or Truvox
Customer Service Dept.

12 Fault diagnosis
The following simple checks may be performed by the operator.

Fault Reason Remedy

Machine not working Lack of voltage/electrical supply.

Check fuse *, supply cord, plug,
socket outlet and circuit breaker.

* If the fuse blows several times, the machine should be checked by an authorised Service Agent.

7

13 Declaration of conformity

EC Declaration of conformity

We, Truvox International Ltd.
Of Third Avenue

Millbrook Trading Estate
Southampton SO15 0LE
England

declare that the machinery
Make : Commercial carpet and floor dryers

Type : Air Mover
Model : AM, AM/T, AM/110, AM/T/110

Year of Construction : from 2006
has been manufactured using the following transposed harmonised European Standards and

technical specifications.

BS EN 50081-1, BS EN 55014-1 & 2, BS EN 60335-1 and BS EN 60335-2-80,
and is in conformity with:

the Machinery Directive 89/392/EEC and subsequent amendments,
the Low Voltage Directive 73/23/EEC and subsequent amendments,
and the EMC Directive 89/336/EEC and subsequent amendments.
Signed in : SOUTHAMPTON, England
on the 1st day of December 2006

Signature :
Name : Malcolm Eneas

Position : Vice President Engineering
Tacony CFC

8

Truvox International Limited
Third Avenue, Millbrook, Southampton, Hampshire SO15 0LE, England
Tel: [phone] Fax: [phone]
e-mail: [e-mail] Web: www.truvox.com