Trusted Clean TPL-BK-13-TC, TPL-BPC-17-ST-PD-CF, TPL-SS-20HD-TC, TPL-SS-17VS-TC, TPL-SS-15-TC Owner's/operator's Manual
...Page 1
FOR MODELS:
TPL-BK-13-TC
TPL-SS-15-TC
TPL-SS-17-TC
TPL-BPC-17- ST-PD- CF
TPL-SS-20HD-TC
TPL-SS-17VS-TC
TPL-SS-20VS-TC
LOW SPEED AND DUAL SPEED
FLOOR MACHINE
OWNER’S/OPERATOR’S MANUAL
WWW.CLEANFREAK.COM
888-522-5508
REVISED 9-16-16
Page 2
UNPACKING YOUR NEW LOW SPEED OR
DUAL SPEED FLOOR MACHINE:
When your package is delivered, check each of the 3
cartons carefully for signs of rough handling. If the
LOW SPEED OR DUAL SPEED FLOOR MACHINE is
damaged, notify the carrier immediately and request an
inspection. Be sure to keep the cartons, packing inserts,
packing lists and carrier’s receipt until the inspector has
veried your claim.
CLEANFREAK.COM’s liability ceases when the carrier
picks up the shipment. However, our customer service
sta will be happy to furnish any information needed in
connection with the claim and will attempt to expedite a
resolution.
PLEASE READ BEFORE
OPERATING YOUR NEW LOW SPEED OR
DUAL SPEED FLOOR MACHINE:
Read the manual carefully and completely before attempting to operate the unit. is manual has important
information for the use and safe operation of the machine. Keep this manual handy at all times.
is equipment has been engineered and manufactured
to provide excellent performance and service. To ensure
that your equipment will continue to perform as intended:
• Maintain and inspect equipment regularly.
• Use only original CLEANFREAK.COM parts when
servicing.
• Operate equipment with care.
If additional information is needed, please contact
CLEANFREAK.COM at: 888-722-5508
All information and specications printed in the manual
are current at the time of printing; however, because of
CLEANFREAK.COM’s policy of continual product improvement, we reserve the right to make changes at any
time without notice.
FAILURE TO COMPLY WITH THE FOL-
LOWING WARNINGS AND INSTRUC-
TIONS WILL VOID THE WARRANTY.
WARNING!
• Do not operate the machine unless trained and authorized.
• Do not leave the machine unattended when plugged
in. Unplug from the outlet when not in use, before
servicing, and when changing the brushes or pads.
• Use indoors only.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Do not bypass or defeat the safety “lock-out lever.”
• e machine was designed for use as per instructions and recommendations written in this manual.
Any deviation from its proper use or purpose and
the consequential damage that may occur is the sole
responsibility of the end user.
• Do not use with damaged cord or plug. If the machine is not working as it should, or it has been
dropped, damaged, le outdoors or dropped into
water, take it to an authorized service center.
• Do not pull or carry by cord, use cord as handle,
close a door on the cord or pull cord around sharp
edges or corners. Do not run machine over cord.
Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Make sure the machine is plugged into an electrical
outlet with the same voltage and frequency rating
as shown on the nameplate of the machine. Do not
attempt to plug a 115- volt machine into a 230- volt
outlet.
• Do not immerse or use this machine in standing
water. Such use can cause electric shock.
• Keep the electrical supply cord from contacting the
rotating brush or drive block.
• Do not expose machine to freezing temperatures.
• To avoid electric shock, do not expose the unit to
rain. Store indoors only.
• Connect to a properly grounded outlet only. See
“Grounding Instructions.”
• Turn o all controls before unplugging.
• When using an extension cord, use a 3 conductorgrounding cord, 12 gauge wire or heavier. Do not use
more than 25’ of extension cord.
• Do not put any object into openings.
2
Page 3
• Do not use with any opening blocked. Keep free of
dust, lint, hair and anything that may reduce air ow.
• Do not operate machine in ammable or explosive
areas.
• All servicing of CLEANFREAK.COM equipment
should be performed by an CLEANFREAK.COM
authorized service center.
• Keep hair, loose clothing, ngers and all parts of
body away from openings and moving parts.
• Use extra care when cleaning near stairs.
• When servicing machine, use manufacturer’s supplied or approved replacement parts.
• Do not wrap the cord too tightly when storing.
• Work only in well lit areas.
• is equipment is heavy. Use proper liing techniques when liing heavy equipment.
GROUNDING INSTRUCTIONS:
is piece of equipment must be grounded. Should an
electrical malfunction occur, grounding provides a path
of least resistance for electrical current- reducing the risk
of electric shock. is piece of equipment is furnished
with a cord that has a grounding conductor and grounding plug. e grounded plug must only be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
e Green (or Green/Yellow) wire in the cord is the
grounding wire. When replacing a plug, this wire must
be attached to the grounding pin only.
DO NOT use extension cords.
PREPARING THE MACHINE FOR
OPERATION
Your oor machine will operate in a wide variety of hard
oors and carpet cleaning applications. Consult with
your local dealer or CLEANFREAK.COM Customer
Service to select the correct accessories for the job you
are going to perform.
BRUSH, PAD DRIVER
INSTALLATION
Lock the handle in the upright position and tip the machine back so it rests on the handle and wheels. Fit the
three slots of the clutch plate in the back of the brush
or pad driver over the three lugs of the drive plate (Fig.
1). Push it rmly into position and turn it counterclockwise until it locks in place (Fig. 2).
WARNING:
Connecting the equipment to an improperly grounded
outlet can result in an increased risk of electric shock. A
qualified electrician should be consulted if you are unsure that the outlet is properly grounded. Do not modify
the plug provided with the equipment. If it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
is appliance is designed for use on a 120-volt circuit.
e grounding plug provided looks like the plug illustrated in Figure 1. Replace the plug if the grounding pin
is damaged or broken.
Figure 1
Fig. 1
Fig. 2
TO REMOVE PAD DRIVER:
Tip the machine back so it rests on the
handle and wheels. Turn the brush or pad driver
clockwise until it disengages and lis o.
Do not store the machine with the brush or pad drivers
installed.
3
Page 4
PAD INSTALLATION
TO INSTALL PAD: Tilt the machine back on wheels
until machine is resting on handle. Center the pad on the
pad holder and press the pad onto the pad holder.
TO REMOVE PAD: Remove the pad from the pad holder by pulling it away from the pad holder with steady
force.
MACHINE OPERATION:
is equipment is equipped with a safety “LOCK OUT”
lever. Refer to Diagram 1 for steps 4, 5, and 6.
1. Install the pad driver and pad or attachment.
2. Plug in machine.
3. Adjust the handle to the desired operating position.
4. Place both hands on the handle grips with your ngers around the ON/OFF lever (Refer to B on Diagram 1) Which extends from one side to the other,
underneath the handle grips.
5. e safety “LOCK OUT” lever (Refer to A on Diagram 1) is located underneath the right side handle
grip and switch lever. To unlock the “LOCK OUT”
lever, use your right hand fore nger to press the
lever toward the back of the switch box.
6. With “LOCK OUT” lever in the unlocked position,
pull up on either side of the ON/OFF lever (Refer to
B on Diagram 1) to power the motor. Pull up on only
one side of the ON/OFF lever.
TO MANEUVER YOUR FLOOR MACHINE
1. Raise the handle slightly and the machine will go to
the right. e higher you raise it, the faster it will go.
2. Lower the handle and the machine will go le. e
more you lower it, the faster it will go.
3. Practice on a smooth surface to gain experience in
operating the unit before moving on to other surfaces.
DUAL SPEED FUNCTION FOR 17DS3-BK &
20DS3-BK:
Use the black switch located directly behind the motor
to switch between low speed (180RPM) and high speed
(320RPM). Do not change speeds while machine is running. Always wait until motor has stopped completely
before changing speeds.
Storage:
Wipe with a clean damp cloth aer every use.
Store in a clean dry place.
CORD STORAGE:
• Unplug the cord- Clean and inspect for damage.
• Wrap the cord around the le side handle grip.
• Do not wrap too tightly.
SERVICING:
In the event that your LOW SPEED OR DUAL SPEED
FLOOR MACHINE requires service, please contact
CLEANFREAK.COM: 888-722-5508
No user serviceable components are employed in this
equipment. Do not attempt repairs yourself. CLEANFREAK.COM will assist you in locating an indepedent
service contractor.
B
A
Diagram 1
B
NOTE:
BREAKDOWNS FOR THE MOST COMMON
LOW SPEED OR DUAL SPEED FLOOR MACHINE
VERSIONS HAVE BEEN INCLUDED.
IF YOURS IS NOT LISTED, CONTACT CLEANFREAK.COM FOR ASSISTANCE.
4
Page 5
70
1
2
3
5 6
7
8
9
10
12 13 14 15
11
16
17
52
50
68
67
62
61
60
59
66
58
65
64
63
555657
54
53
18 19
20
21
22
23
24
25
26
27
28
29
30
46
45
44
42
41
40
39
69
LOW SPEED
MODELS:
TPL-BK-13-TC
TPL-SS-15-TC
TPL-SS-17-TC
TPL-BPC-17- ST-PD- CF
TPL-SS-20HD-TC
5
31
32
33
34
35
36
37
38
Page 6
ITEM
NO.
PART NUMBER QTY.
ITEM
NO.
PART NUMBER QTY.
1
B11487-BLUE Power Cord, 14-3, 50
FT, SJTW
1
D11482 Handle Brace, Right,
Black
1
2
K11498 Grip
2 35
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 36
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 37
G11943 Wheel, 5 in Saturn
2
6
D11496B Switch Box Cover, Black
1 38
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor
Machine
1 39
C11501 Socket Cap Screw, .31 18
4
8
C11529 Screw, 10-32 X .375 in
2 40
C00251 Lockwasher, .31, Split
4
9
K11519 Lever Grip, Lockout, Black
1 41
E11476-BLUE Bumper, 13 in Floor
Machine
1
10
C00278 Locknut, 10-32, Nylon, SS
1 42
D11484B Brush Cover, 13 in, Black
1
11
D11494 Lockout Bracket
1 44
D11483C Chrome Motor Frame
1
12
D11524 Spring, Lockout
1 45
G11468 Motor W-Gearbox, 1.5 HP
115v
1
13
C90007 Screw, 10-32 X .625
Phillips, Truss Head, SS
1 46
D11481 Handle Brace, Left, Black
1
14
C11491 Screw, 10-32 X 1 in, SS
1 50
D11490B Drip Cover, Black
1
15
D11479-1 Handle, Chrome,
Floormachine
1 52
C11916 Screw, 10-32 X .375 Phillips
3
16
C00306 Roll Pin, .125 X 1.75
2 53
C13100 Nut, M14-2.0 Nylon Insert
1
17
D11523 Spring, Trigger
2 54
B10734 Strain Relief, Handle
1
18
D11495 Trigger, Zinc Plated
1 55
B11513 Cord, Handle, 14-3 SJTW
1
19
K11520 Lever Grip, Trigger, Black
2 56
B11762 Terminal Lug, Nylon,
Female
2
20
11507A Assembled Locking
Handle, Cord Hook
1 57
B11465 Switch, DPST, Pushbutton
1
21
C11619 Allen Wrench, .31 in
1 58
B00177 Terminal Lug, Female, QD,
.25 X .032
2
22
D11497 Handle, Locking Clamp
1 59
C00252 Washer, .375 in, Flat
1
23
C11538 Cap Nut, .31 in, Push-On
1 60
C11541 Washer, .375 in, Star
1
24
C00259 Washer, Slotted, Zinc
1 61
B11518 Switch Insulation
1
25
C11536 Spade Bolt, .375-16 X 4 in
1 62
C00284 Screw, 10-32 X .375
Ground
1
26
D11507-2 Cord Hook Clamp
1 63
B00187 Cable Clamp, Nylon, .43
in.
1
27
D11507 Cord Hook Body
1 64
B00180-10-3 Ring Terminal, #10
Center
2
28
C11558 Locknut, Black Oxide, Thin
2 65
B11505 Strain Relief Nut, Metal
1
29
C11502 Socket Cap Screw, .37516 X 2.5 in
1 66
C11560 Washer, .93 ID X 1.5 OD
1
30
C11537 Dowel Pin, .31 X 1.5 in
1 67
B11504 Strain Relief, Metal
1
31
C22558 Handle Pivot Bolt
1 68
H02548-2 Label, Important, Cord
1
32
K00674 Bushing, .50 in, Nylon
2 69
H11908 TC SWITCH BOX LABEL 1
33
D11510 Axle, Floor Machine
1 70
H11909 TC MOTOR LABEL 1
MODEL: TPL-BK-13-TC
34
6
Page 7
ITEM
NO.
PART NUMBER QTY.
ITEM
NO.
PART NUMBER QTY.
1
B11487-BLUE Power Cord, 14-3, 50
FT, SJTW
1
D11482 Handle Brace, Right,
Black
1
2
K11498 Grip
2 35
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 36
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 37
G11943 Wheel, 5 in Saturn
2
6
D11496B Switch Box Cover, Black
1 38
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor
Machine
1 39
C11501 Socket Cap Screw, .31 18
4
8
C11529 Screw, 10-32 X .375 in
2 40
C00251 Lockwasher, .31, Split
4
9
K11519 Lever Grip, Lockout, Black
1 41
E13198-BLUE Bumper, 15 in Floor
Machine
1
10
C00278 Locknut, 10-32, Nylon, SS
1 42
D13194-SS Brush Cover, 15 in,
chrome
1
11
D11494 Lockout Bracket
1 44
D11483C Chrome Motor Frame
1
12
D11524 Spring, Lockout
1 45
G11468 Motor W-Gearbox, 1.5 HP
115v
1
13
C90007 Screw, 10-32 X .625
Phillips, Truss Head, SS
1 46
D11481 Handle Brace, Left, Black
1
14
C11491 Screw, 10-32 X 1 in, SS
1 50
D11490c Drip Cover, Chrome
1
15
D11479-1 Handle, Chrome,
Floormachine
1 52
C11916 Screw, 10-32 X .375 Phillips
3
16
C00306 Roll Pin, .125 X 1.75
2 53
C13100 Nut, M14-2.0 Nylon Insert
1
17
D11523 Spring, Trigger
2 54
B10734 Strain Relief, Handle
1
18
D11495 Trigger, Zinc Plated
1 55
B11513 Cord, Handle, 14-3 SJTW
1
19
K11520 Lever Grip, Trigger, Black
2 56
B11762 Terminal Lug, Nylon,
Female
2
20
11507A Assembled Locking
Handle, Cord Hook
1 57
B11465 Switch, DPST, Pushbutton
1
21
C11619 Allen Wrench, .31 in
1 58
B00177 Terminal Lug, Female, QD,
.25 X .032
2
22
D11497 Handle, Locking Clamp
1 59
C00252 Washer, .375 in, Flat
1
23
C11538 Cap Nut, .31 in, Push-On
1 60
C11541 Washer, .375 in, Star
1
24
C00259 Washer, Slotted, Zinc
1 61
B11518 Switch Insulation
1
25
C11536 Spade Bolt, .375-16 X 4 in
1 62
C00284 Screw, 10-32 X .375
Ground
1
26
D11507-2 Cord Hook Clamp
1 63
B00187 Cable Clamp, Nylon, .43
in.
1
27
D11507 Cord Hook Body
1 64
B00180-10-3 Ring Terminal, #10
Center
2
28
C11558 Locknut, Black Oxide, Thin
2 65
B11505 Strain Relief Nut, Metal
1
29
C11502 Socket Cap Screw, .37516 X 2.5 in
1 66
C11560 Washer, .93 ID X 1.5 OD
1
30
C11537 Dowel Pin, .31 X 1.5 in
1 67
B11504 Strain Relief, Metal
1
31
C22558 Handle Pivot Bolt
1 68
H02548-2 Label, Important, Cord
1
32
K00674 Bushing, .50 in, Nylon
2 69
H11908 TC SWITCH BOX LABEL 1
33
D11510 Axle, Floor Machine
1 70
H11909 TC MOTOR LABEL 1
MODEL: TPL-SS-15-TC
34
7
Page 8
ITEM
NO.
PART NUMBER QTY.
ITEM
NO.
PART NUMBER QTY.
1
B11487-BLUE Power Cord, 14-3, 50
FT, SJTW
1
D11482 Handle Brace, Right,
Black
1
2
K11498 Grip
2 35
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 36
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 37
G11943 Wheel, 5 in Saturn
2
6
D11496B Switch Box Cover, Black
1 38
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor
Machine
1 39
C11501 Socket Cap Screw, .31 18
4
8
C11529 Screw, 10-32 X .375 in
2 40
C00251 Lockwasher, .31, Split
4
9
K11519 Lever Grip, Lockout, Black
1 41
E11477-BLUE Bumper, 17 in Floor
Machine
1
10
C00278 Locknut, 10-32, Nylon, SS
1 42
D11485-SS Brush Cover, 17 in,
chrome
1
11
D11494 Lockout Bracket
1 44
D11483C Chrome Motor Frame
1
12
D11524 Spring, Lockout
1 45
G11468 Motor W-Gearbox, 1.5 HP
115v
1
13
C90007 Screw, 10-32 X .625
Phillips, Truss Head, SS
1 46
D11481 Handle Brace, Left, Black
1
14
C11491 Screw, 10-32 X 1 in, SS
1 50
D11490c Drip Cover, Chrome
1
15
D11479-1 Handle, Chrome,
Floormachine
1 52
C11916 Screw, 10-32 X .375 Phillips
3
16
C00306 Roll Pin, .125 X 1.75
2 53
C13100 Nut, M14-2.0 Nylon Insert
1
17
D11523 Spring, Trigger
2 54
B10734 Strain Relief, Handle
1
18
D11495 Trigger, Zinc Plated
1 55
B11513 Cord, Handle, 14-3 SJTW
1
19
K11520 Lever Grip, Trigger, Black
2 56
B11762 Terminal Lug, Nylon,
Female
2
20
11507A Assembled Locking
Handle, Cord Hook
1 57
B11465 Switch, DPST, Pushbutton
1
21
C11619 Allen Wrench, .31 in
1 58
B00177 Terminal Lug, Female, QD,
.25 X .032
2
22
D11497 Handle, Locking Clamp
1 59
C00252 Washer, .375 in, Flat
1
23
C11538 Cap Nut, .31 in, Push-On
1 60
C11541 Washer, .375 in, Star
1
24
C00259 Washer, Slotted, Zinc
1 61
B11518 Switch Insulation
1
25
C11536 Spade Bolt, .375-16 X 4 in
1 62
C00284 Screw, 10-32 X .375
Ground
1
26
D11507-2 Cord Hook Clamp
1 63
B00187 Cable Clamp, Nylon, .43
in.
1
27
D11507 Cord Hook Body
1 64
B00180-10-3 Ring Terminal, #10
Center
2
28
C11558 Locknut, Black Oxide, Thin
2 65
B11505 Strain Relief Nut, Metal
1
29
C11502 Socket Cap Screw, .37516 X 2.5 in
1 66
C11560 Washer, .93 ID X 1.5 OD
1
30
C11537 Dowel Pin, .31 X 1.5 in
1 67
B11504 Strain Relief, Metal
1
31
C22558 Handle Pivot Bolt
1 68
H02548-2 Label, Important, Cord
1
32
K00674 Bushing, .50 in, Nylon
2 69
H11908 TC SWITCH BOX LABEL 1
33
D11510 Axle, Floor Machine
1 70
H11909 TC MOTOR LABEL 1
MODEL: TPL-SS-17-TC & TPL-BPC-17-ST-PD-CF
34
8
Page 9
MODEL: TPL-SS-20HD-TC
ITEM
NO.
PART NUMBER QTY.
ITEM
NO.
PART NUMBER QTY.
1
B11487-BLUE Power Cord, 14-3, 50
FT, SJTW
1
D11482 Handle Brace, Right,
Black
1
2
K11498 Grip
2 35
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 36
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 37
G11943 Wheel, 5 in Saturn
2
6
D11496B Switch Box Cover, Black
1 38
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor
Machine
1 39
C11501 Socket Cap Screw, .31 18
4
8
C11529 Screw, 10-32 X .375 in
2 40
C00251 Lockwasher, .31, Split
4
9
K11519 Lever Grip, Lockout, Black
1 41
E11478-BLUE Bumper, 20 in Floor
Machine
1
10
C00278 Locknut, 10-32, Nylon, SS
1 42
D11486-SS Brush Cover, 20 in,
chrome
1
11
D11494 Lockout Bracket
1 44
D11483C Chrome Motor Frame
1
12
D11524 Spring, Lockout
1 45
G11468 Motor W-Gearbox, 1.5 HP
115v
1
13
C90007 Screw, 10-32 X .625
Phillips, Truss Head, SS
1 46
D11481 Handle Brace, Left, Black
1
14
C11491 Screw, 10-32 X 1 in, SS
1 50
D11490c Drip Cover, Chrome
1
15
D11479-1 Handle, Chrome,
Floormachine
1 52
C11916 Screw, 10-32 X .375 Phillips
3
16
C00306 Roll Pin, .125 X 1.75
2 53
C13100 Nut, M14-2.0 Nylon Insert
1
17
D11523 Spring, Trigger
2 54
B10734 Strain Relief, Handle
1
18
D11495 Trigger, Zinc Plated
1 55
B11513 Cord, Handle, 14-3 SJTW
1
19
K11520 Lever Grip, Trigger, Black
2 56
B11762 Terminal Lug, Nylon,
Female
2
20
11507A Assembled Locking
Handle, Cord Hook
1 57
B11465 Switch, DPST, Pushbutton
1
21
C11619 Allen Wrench, .31 in
1 58
B00177 Terminal Lug, Female, QD,
.25 X .032
2
22
D11497 Handle, Locking Clamp
1 59
C00252 Washer, .375 in, Flat
1
23
C11538 Cap Nut, .31 in, Push-On
1 60
C11541 Washer, .375 in, Star
1
24
C00259 Washer, Slotted, Zinc
1 61
B11518 Switch Insulation
1
25
C11536 Spade Bolt, .375-16 X 4 in
1 62
C00284 Screw, 10-32 X .375
Ground
1
26
D11507-2 Cord Hook Clamp
1 63
B00187 Cable Clamp, Nylon, .43
in.
1
27
D11507 Cord Hook Body
1 64
B00180-10-3 Ring Terminal, #10
Center
2
28
C11558 Locknut, Black Oxide, Thin
2 65
B11505 Strain Relief Nut, Metal
1
29
C11502 Socket Cap Screw, .37516 X 2.5 in
1 66
C11560 Washer, .93 ID X 1.5 OD
1
30
C11537 Dowel Pin, .31 X 1.5 in
1 67
B11504 Strain Relief, Metal
1
31
C22558 Handle Pivot Bolt
1 68
H02548-2 Label, Important, Cord
1
32
K00674 Bushing, .50 in, Nylon
2 69
H11908 TC SWITCH BOX LABEL 1
33
D11510 Axle, Floor Machine
1 70
H11909 TC MOTOR LABEL 1
34
9
Page 10
70
1
2
3
5 6
7
8
9
10
12 13 14 15
11
16
17
52
50
68
67
62
61
60
59
66
58
65
64
63
555657
54
53
18 19
20
21
22
23
24
25
26
27
28
29
30
46
45
44
42
41
40
39
10
69
32
DUAL SPEED
MODELS:
TPL-SS-17VS-TC
TPL-SS-20VS-TC
31
33
34
35
36
37
38
Page 11
ITEM
PART NUMBER QTY.
ITEM
PART NUMBER QTY.
1
B11487-Blue Power Cord, 14-3, 50 FT, SJTW
1 42
D11482 Handle Brace, Right, Black
1
2
K11498 Grip
2 43
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 44
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 45
G11943 Wheel, 5 in Saturn
2
6
D11496C Switch Box Cover, Chrome
1 46
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor Machine
1 47
B00185-30 Wire, 14 Ga X 2 ft, White, UL195
1
8
C11529 Screw, 10-32 X .375 in
2 48
B00185-40 Wire, 14 Ga X 2 ft, Black, UL1015
1
9
K11519 Lever Grip, Lockout, Black
1 49
B00185-86 Wire, 14 Ga X 2 ft, Red, UL1015
1
10
C00278 Locknut, 10-32, Nylon, SS
1 50
B00228-2 1 Foot Shrinktube, .375 in, Poly
1
11
D11494 Lockout Bracket
1 51
C11619 Allen Wrench, .31 in
1
12
D11524 Spring, Lockout
1 52
C11501 Socket Cap Screw, .31 - 18
4
13
C90007 Screw, 10-32 X .625 Phillips, Truss Head,
SS
4 53
C00251 Lockwasher, .31, Split
4
14
C11491 Screw, 10-32 X 1 in, SS
1 54
E11477-BLUE Bumper, 17 INCH Floor Machine
1
15
C00306 Roll Pin, .125 X 1.75
2 55
D11485-SS Brush Cover, 17 INCH, cHROME
1
16
D11523 Spring, Trigger
2 57
D11483C Frame, Motor, Chrome
1
17
D11479 Handle, Chrome, Floormachine
1 58
D11545 Motor Screen
1
18
D11495 Trigger, Zinc Plated
1 59
11573A Motor assembly 115v
1
19
K11520 Lever Grip, Trigger, Black
2 60
B00181 Butt Connector, Blue, 1 Wire
1
20
11507A Assembled Locking Handle, Cord
Hook
1 61
B00179-1 Closed End Cntr, 16-3
1
21
D11497 Handle, Locking Clamp
1 62
D11481 Handle Brace, Left, Black
1
22
C11538 Cap Nut, .31 in, Push-On
1 63
K11517 Spacer, .19 ID X .375 High X .50 OD,
Nylon
3
23
C00259 Washer, Slotted, Zinc
1 64
B11199 Strain Relief, Pigtail w-Locknut
1
24
C11536 Spade Bolt, .375-16 X 4 in
1 65
H10976-1 Label, UL STD 561-507
1
25
D11507 Cord Hook Clamp
1 68
D11490C-H Drip Cover w - Hole for Light BLK
1
26
D11507-2 Cord Hook Body
1 70
B02196-1 Light, Motor Carbon Brush Wear
1
27
C11558 Locknut, .375-16, Nylon
2 71
C13100 Nut, M14-2.0 Nylon Insert
1
28
C11502 Socket Cap Screw, .375-16 X 2.5 in
1 72
B10734 Strain Relief, Handle
1
29
C11537 Dowel Pin, .31 X 1.5 in
1 73
B11513 Cord, Handle, 14-3 SJTW
1
30
C13101 Screw, Hex Cap, M14-2.0
1 74
B11762 Terminal Lug, Nylon, Female
2
31
B13156 power cord 16/3 3 ft
1 75
B11465 Switch, DPST, Pushbutton
1
32
B11518 Switch Insulation
3 76
C00252 Washer, .375 in, Flat
1
33
B11751 Switch, Rocker, DPDT, Black
1 77
C11541 Washer, .375 in, Star
1
34
C00293 #8 X .5in Pan, Black SMS, Phillips
2 78
C00284 Screw, 10-32 X .375 Ground
1
35
D11582 Bracket, Switch Mount
1 79
B00187 Cable Clamp, Nylon, .43 in.
1
36
C00297 Screw,#8 X .25 in, Pan Head
4 80
B00180-10-3 Ring Terminal, #10 Center
2
37
D11646 Switch Bracket Cover
2 81
B11505 Strain Relief Nut, Metal
1
38
B00177-1 Terminal Lug, Female, QD, .25 X .032
1 82
C11560 Washer, .93 ID X 1.5 OD
1
39
B00177 Terminal Lug, Female, QD, .25 X .032
11 83
B11504 Strain Relief, Metal
1
40
K00674 Bushing, .50 in, Nylon
2 84
H02548-2 Label, Important, Cord
1
41
D11510 Axle, Floor Machine
1 85
H11909 TC SWITCHBOX LABEL
1
MODEL: TPL-SS-17VS-TC
NO.
NO.
11
Page 12
ITEM
PART NUMBER QTY.
ITEM
PART NUMBER QTY.
1
B11487-Blue Power Cord, 14-3, 50 FT, SJTW
1 42
D11482 Handle Brace, Right, Black
1
2
K11498 Grip
2 43
C00240 Washer, Shoulder, Nylon
6
3
C11528 Screw, 10-32 X .25 in
1 44
C11559 Washer, .515 X .875 X .032
6
5
H12066 1.5HP Label
1 45
G11943 Wheel, 5 in Saturn
2
6
D11496C Switch Box Cover, Chrome
1 46
C02305 Cap Nut, .5in Push-on
2
7
H11493 Label, Safety, Floor Machine
1 47
B00185-30 Wire, 14 Ga X 2 ft, White, UL195
1
8
C11529 Screw, 10-32 X .375 in
2 48
B00185-40 Wire, 14 Ga X 2 ft, Black, UL1015
1
9
K11519 Lever Grip, Lockout, Black
1 49
B00185-86 Wire, 14 Ga X 2 ft, Red, UL1015
1
10
C00278 Locknut, 10-32, Nylon, SS
1 50
B00228-2 1 Foot Shrinktube, .375 in, Poly
1
11
D11494 Lockout Bracket
1 51
C11619 Allen Wrench, .31 in
1
12
D11524 Spring, Lockout
1 52
C11501 Socket Cap Screw, .31 - 18
4
13
C90007 Screw, 10-32 X .625 Phillips, Truss Head,
SS
4 53
C00251 Lockwasher, .31, Split
4
14
C11491 Screw, 10-32 X 1 in, SS
1 54
E11478-BLUE Bumper, 20 INCH Floor Machine
1
15
C00306 Roll Pin, .125 X 1.75
2 55
D11486-SS Brush Cover, 20 INCH, cHROME
1
16
D11523 Spring, Trigger
2 57
D11483C Frame, Motor, Chrome
1
17
D11479 Handle, Chrome, Floormachine
1 58
D11545 Motor Screen
1
18
D11495 Trigger, Zinc Plated
1 59
11573A Motor assembly 115v
1
19
K11520 Lever Grip, Trigger, Black
2 60
B00181 Butt Connector, Blue, 1 Wire
1
20
11507A Assembled Locking Handle, Cord
Hook
1 61
B00179-1 Closed End Cntr, 16-3
1
21
D11497 Handle, Locking Clamp
1 62
D11481 Handle Brace, Left, Black
1
22
C11538 Cap Nut, .31 in, Push-On
1 63
K11517 Spacer, .19 ID X .375 High X .50 OD,
Nylon
3
23
C00259 Washer, Slotted, Zinc
1 64
B11199 Strain Relief, Pigtail w-Locknut
1
24
C11536 Spade Bolt, .375-16 X 4 in
1 65
H10976-1 Label, UL STD 561-507
1
25
D11507 Cord Hook Clamp
1 68
D11490C-H Drip Cover w - Hole for Light BLK
1
26
D11507-2 Cord Hook Body
1 70
B02196-1 Light, Motor Carbon Brush Wear
1
27
C11558 Locknut, .375-16, Nylon
2 71
C13100 Nut, M14-2.0 Nylon Insert
1
28
C11502 Socket Cap Screw, .375-16 X 2.5 in
1 72
B10734 Strain Relief, Handle
1
29
C11537 Dowel Pin, .31 X 1.5 in
1 73
B11513 Cord, Handle, 14-3 SJTW
1
30
C13101 Screw, Hex Cap, M14-2.0
1 74
B11762 Terminal Lug, Nylon, Female
2
31
B13156 power cord 16/3 3 ft
1 75
B11465 Switch, DPST, Pushbutton
1
32
B11518 Switch Insulation
3 76
C00252 Washer, .375 in, Flat
1
33
B11751 Switch, Rocker, DPDT, Black
1 77
C11541 Washer, .375 in, Star
1
34
C00293 #8 X .5in Pan, Black SMS, Phillips
2 78
C00284 Screw, 10-32 X .375 Ground
1
35
D11582 Bracket, Switch Mount
1 79
B00187 Cable Clamp, Nylon, .43 in.
1
36
C00297 Screw,#8 X .25 in, Pan Head
4 80
B00180-10-3 Ring Terminal, #10 Center
2
37
D11646 Switch Bracket Cover
2 81
B11505 Strain Relief Nut, Metal
1
38
B00177-1 Terminal Lug, Female, QD, .25 X .032
1 82
C11560 Washer, .93 ID X 1.5 OD
1
39
B00177 Terminal Lug, Female, QD, .25 X .032
11 83
B11504 Strain Relief, Metal
1
40
K00674 Bushing, .50 in, Nylon
2 84
H02548-2 Label, Important, Cord
1
41
D11510 Axle, Floor Machine
1 85
H11909 TC SWITCHBOX LABEL
1
MODEL: TPL-SS-20VS-TC
NO.
NO.
12
Page 13
LOW SPEED
WIRING
AC MOTOR
B
W
G
B
W
G
SWITCH
B
W
G
HANDLE MOTOR
13
Page 14
DUAL SPEED WIRING
AC MOTOR
6
14
Page 15
NOTES
15
Loading...