Trumeter APM-TEMP-ANO, APM-TEMP-APO, APM-TEMP-APS, APM-TEMP-ANS User manual

Intended Use
APM
Tem Meter
perature
CAUTION: Risk of Danger
Read complete instructions prior to installation and operation of the unit
CAUTION: Risk of electric shock
Before installation, read the Safety Warnings overleaf.
Intended Use: The APM has been specifically designed for engineers requiring an effective way to monitor and display data. The APM accepts a range of electrical inputs (depending on the model) and displays the data on its integrated multi-format display. The APM has been designed for installation into electrical cabinets or display panels. Output models include two independent outputs that can be configured by the user to be either digital set-point outputs or 4-20mA monitor outputs.
Operating SpecificationOperating Specification
Use the DIP switches to set the Temperature Meter bar graph range and annunciators to standard values. Use the software application to configure custom settings. The switch positions are shown in the table where: 0 = OFF and 1 = ON.
Thermocouple Types
Accuracy
The DIP switches are on the back of the unit.
B, C, E, J, K, N, R, S, T
0.25% plus Thermocouple Accuracy
Size of the cutout in the panel:
68 x 68mm (2.68in) +0.7 -0mm
Size
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
PSU
Wiring Diagrams
DIP Switches
DIP switch settings:-
Thermocouple Input
Switch
-
+
Fuse
DC supply ONLY AC supply must not have COM link
1234 Min Max Min 0000 Custom
1000 B 250 1820 ºC 0 200 0100 E -200 1000 ºC 0 1000
Type
Thermocouple
Units
1100 J -210 1200 ºC 0 1200 0010 K -200 1372 ºC 0 140 X10 1010 N -200 1300 ºC 0 140 X10 0110 R -50 1768 ºC 0 200 X10 1110 S -50 1768 ºC 0 200 0001 T -200 400 ºC 0 400 1001 B 482 3308 ºF 0 400 0101 E -328 1832 ºF 0 1101 J
-
346 2192 ºF 0 0011 K -328 2502 ºF 0 1011 N -328 2372 ºF 0 0111 R -58 3214 ºF 0 1111 S -58 3214 ºF 0
Thermocouple Input
Display Scale
Max X10
X10
X10
X10 200 X10 220 260 240 320 320
X10
X10
X10
X10
X10
4-20 mA analogue output using setpoint 1.
12 - 24V
PSU
-
+
Fuse
0V
4-20mA
Output
Analogue Output and relay using both setpoints.
4-20mA
0V
-
+
Fuse
+
RELAY
-
12-24V PSU
Outputs
Using a diode-protected relay on setpoint 1.
12-24V PSU
-
+
Fuse
+
RELAY
-
Use the Reset input with the peak hold function.
12-24V PSU
- ~ + ~
Fuse
You need the software to configure the setpoints and outputs.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Safety Warnings
WARNING: INSTALLATION AND MAINTENANCE MUST BE CARRIED OUT BY SUITABLY QUALIFIED AND COMPETENT PERSONEL ONLY. HAZARDOUS VOLTAGES MAY BE PRESENT ON THE CONNECTION TERMINALS.
INSTALLATION
Install this product in accordance with local regulations, codes
and instructions.
All fuses must be 0.5A / 250V Type F with a breaking capacity
of 35A or greater.
All conductors carrying
switching or 3 mm of contact separation in all poles.
Signal cables connected to this device must not exceed 30
metres long.
If signal cables are routed outside the building, install extra
surge-protection devices.
Power supply, current input, USB and all outputs: Observe
maximum allowable voltages. All circuits connected to these connectors must be limited-energy and insulated by double/ reinforced insulation from mains voltages according to IEC 61010-1:2010
disconnect mechanisms fitted that provide at least
hazardous voltage
must have external
Failure to install or operate the unit in accordance with the above requirements may impair the electrical safety of the unit. Voltage measurements: An external UL recognized or listed overcurrent protection device (fuse or circuit breaker) must be fitted in-line with the voltage lead. Recommended fuse: 0.5A Type F with a breaking capacity of 35A or greater. Fuse voltage rating must be greater than the maximum voltage that will be applied to the meter.
MAINTENANCE
Before cleaning, inspection or maintenance, isolate all power sources to the unit.
There are no user-serviceable parts inside this unit. Never open the case.
Inspect all external wiring connections at regular intervals. Replace any damaged connections.
To clean
Take great care connecting the supply. If you connect power
to the wrong terminals, it may destroy the unit.
unit, use a dry cloth to wipe the casing.
the
wiring and tighten
any loose
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Specification
Environment
Temperature - operating
Temperature - storage Altitude Relative Humidity (non-condensing) - Continuous Relative Humidity (non-condensing) - Intermittent
Pollution Degree (IEC664)
IP rating (from the front)
NEMA Rating (from the front)
Power supply
Input Max Power
Supply Frequency
Isolation
Display
Number of digits Digit height
Number of bar-graph segments Number of starburst message characters Backlight colours LCD Digit update frequency Bar-graph update frequency
Viewing angle
Open Collector Outputs
Max voltage (open collector outputs)
Max current (open collector outputs)
Analogue Output
Output Accuracy Resolution
Connections
Thermocouple Inputs are referenced to PSU 0V. Appying additional voltages to Thermocouple Inputs will give an incorrect reading and may damage the meter.
Type Wire type Min. cable temperature rating
Wire strip length
Wire gauge
Torque
Certification
CE cULus IEC 61010-1
In the Box
APM Getting started & safety guide Sealing gasket Retaining clip
Panel Cut-out: 68 x 68 mm (2.68 in) +0.7 -0 mm (0.02 in). Max. panel thickness: 10 mm.
Dimensions: Depth behind panel inside front: 55mm (2.17in) incl. external connections. Weight: 180 grams.
VALUE
–10 to +60 deg C –40 to +70 deg C 2000 metres 0 – 85 % 0 – 95 %
2 IP65
Type 4 & Type 12
12-24V AC/DC
1.6W DC & 50-400 Hz
None
4
12 mm 40
4 Red, Green, White
Positive or negative
0.08 – 21 sec
0.08 – 21 sec +/-70° Horizontal
+/-70° Vertical
34 V 500 mA
4-20 mA
0.50 %
0.02 mA
Screw Terminals Solid or Stranded 65 deg C (149F)
6.5mm to 7mm (0.26” to 0.28”)
0.8mm² - 3.3mm² (18AWG to 12AWG)
0.5-0.6Nm (4.42-5.31 lbf-in)
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...