INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
Warning:
Read instructions carefully. If you are unclear as to how
to proceed, consult a qualified electrician. NOTE: Proper
wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to
misplace any of the screws or parts, which are needed to
install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Thread mounting screws (B) into the mounting bar
(A).
STEP 2: Secure mounting bar (A) to outlet box with outlet box
screws (C).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground
wire from the fixture (if supplied) around the green
grounding screw, then connect it to ground wire from
the outlet box (if not fixed on the outlet box) using a
wire connector (not supplied). If ground wire from the
fixture is not supplied, wrap the ground wire (if not
fixed on the outlet box) from the outlet box around the
green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is
round in shape or smooth (seen best when viewed from wire
end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
not twist wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you
can pull the connector off, please carefully re-do
steps 3 and 4 as above, and check again for a firm
connection.
STEP 6: Connect the fixture wire from group B to the white
wire from the outlet box in the same manner. Make
sure no bare wires can be seen outside wire
connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside
outlet box. Raise the face plate (E) over the circular
strap (A), and secure face plate (E) with ball nuts (D)
STEP 2: Install light bulb. (Please do not exceed the maximum
capacity recommended on the socket.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be
ordered from place of purchase. Be sure to use exact wording
from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture
Loading...