True blue power USBT102 Series, M6430102-2, M6430102-3, M6430102-1, M6430102-4 Installation Manual And Operating Instructions

Mid-Continent Instrument Co., Inc.
dba Mid-Continent Instruments and Avionics

9400 E. 34th Street N.

Wichita, KS 67226

PH [phone]
FX [phone]

Revision 1, June 15, 2018

Installation Manual and Operating Instructions

USBT102 Series

Dual USB Charging Port

True Blue Power® a division of
Mid-Continent Instrument Co., Inc.

© Copyright 2018 Mid-Continent

Instrument Co., Inc.

Input Voltage:

10-32 VDC

Input Power:

24 watts max; 1.7 amps @ 14 VDC / 0.85 amps @ 28 VDC

Output Voltage:

5 VDC ±0.25 per port

Output Power:

2.1 amps max per port

Efficiency:

~85% nominal

Weight:

0.13 pounds

Dimensions: (not including connector)

1.50 inches wide X 1.50 inches high X 0.96 inches deep

Charging Ports Type:

USB Standard-A

Mounting:

Panel mount; rear or front

Part Number

Power Input

USB Connector

M6430102-1

Rear

Sealed

M6430102-2

Bottom

Sealed

M6430102-3

Rear

Lighted

M6430102-4

Bottom

Lighted

SECTION 1 GENERAL DESCRIPTION

1.1 INTRODUCTION

The USBT102 Series Dual USB Charging Port is a power accessory that converts 10 to 32 volts of DC
electrical input from a power supply to standard 5V power for any electronic product that charges using a
USB connector. The USBT102 provides two Universal Serial Bus-A (USB-A) ports and can be rear
mounted or front mounted in a variety of locations throughout a vehicle. The unit has been rigorously
tested, providing confidence and convenience to be mounted in either the cabin or cockpit.

This Dual USB Charging Port is designed as a DCP (Dedicated Charging Port) to industry-standard
protocol per the USB Battery Charging 1.2 Compliance Plan. Early-generation or smaller consumer
electronics typically accept one (1.0) amp of power during charging. However, newer electronics, such as
the Apple iPad®, other tablets and larger devices can accept and, in some cases, require up to 2.1 amps
of power to charge and operate. As a high power DCP, the USBT102 can provide up to 2.1 amps of
power to charge any USB device, including the higher demand products. Unlike most dual USB chargers
which provide one (1.0) amp on one port and 2.1 amps on the second port, the USBT102 can provide 2.1
amps of power to both ports simultaneously. With features like short circuit protection, over-current
protection, low voltage shut-down and temperature monitoring, it can handle unforeseen conditions safely.

Small, compact and powerful, with plenty of installation flexibility, the USBT102 is an ideal choice when
selecting a highly useful and effective addition to any vehicle.

1.2 TECHNICAL SPECIFICATIONS

1.2.1 Electrical Attributes

Table 1.1

1.2.2 Physical Attributes

Table 1.2

1.2.3 Configurations

Table 1.3

True Blue Power 2

Revision 1, June 15, 2018

SECTION 2 PRE-INSTALLATION CONSIDERATIONS

2.1 COOLING

No external cooling is required. The unit will become warm when in use. This is normal and within
operational parameters. No special mounting considerations are required; however, mounting to a metal
surface can help dissipate any heat generated and extend the life of the product.

2.2 EQUIPMENT LOCATION

The USBT102 Dual USB Charging Port is designed for mounting flexibility, allowing for installation in the
cockpit or in the cabin. It is designed for panel mounting and can be installed in a rectangular or circular
rear mount configuration or, with an available installation kit, can be front mounted with a cosmetic cover
plate. An instrument mounting adapter bracket is also available to easily mount the unit in a standard 2.25
inch round instrument opening that may already exist in the cockpit panel. There are two versions to
choose from which allow the input connector to be located either on the rear of the unit or from the bottom.

The unit can be mounted in any orientation. Clearance should be provided for the mating connector which
may require an additional inch beyond the rear of the unit.

2.3 ROUTING OF CABLES

Avoid sharp bends in cabling and routing near control cables. Avoid close proximity and contact with
vehicle structures, equipment or other obstructions that could chafe wires during operation and cause
undesirable effects.

2.4 MODIFICATIONS

Each model USBT102 (part number M6430102-( )) has a nameplate that identifies the manufacturer, part

number, description, and technical specifications of the unit. It also includes the “MOD” or modification

number representing notable changes in the hardware design of the unit.

True Blue Power 3

Revision 1, June 15, 2018