True blue power TI1200 Series Installation Manual And Operating Instructions

INSTALLATION MANUAL AND

OPERATING INSTRUCTIONS

TI1200-( ) Series

Static Electrical Power Inverter

True Blue Power® is a division of Mid-Continent Instrument Co., Inc.

Mid-Continent Instrument Co., Inc.
dba Mid-Continent Instruments and Avionics
9400 E. 34
Wichita, KS 67226 Rev B, July 23, 2012

th

Street N. Manual Number 9017680

True Blue Power, Wichita, KS

FOREWORD

This manual provides information intended for use by persons who, in accordance with current regulatory
requirements, are qualified to install this equipment. If further information is required, please contact:

True Blue Power

c/o Mid-Continent Instrument Co., Inc.

Attn: Customer Service Dept.

9400 E. 34

th

St. N.

Wichita, KS 67226 USA

Phone [phone]

Fax [phone]

www.truebluepowerusa.com

www.mcico.com

We welcome your comments concerning this manual. Although every effort has been made to keep it
free of errors, some may occur. When reporting a specific problem, please describe it briefly and include
the manual part number, the paragraph/figure/table number, and the page number. Send your
comments to:

True Blue Power

c/o Mid-Continent Instrument Co., Inc.

Attn: Technical Publications

9400 E. 34

th

St. N.

Wichita, KS 67226 USA

Phone [phone]

Fax [phone]

 Copyright 2012

Mid-Continent Instrument Co., Inc.

REV. B July 23, 2012 2 Manual Number 9017680

True Blue Power, Wichita, KS

REVISION DETAIL

Rev.

Date Approved Detail

A 04/27/12 JRC Initial release.
B 7/23/12 JDS/MKN Page 9; view overlaps. Page 15 (TS) and (TDS) 501 was 500.

REV. B July 23, 2012 3 Manual Number 9017680

True Blue Power, Wichita, KS

TABLE OF CONTENTS

SECTION 1 GENERAL DESCRIPTION

1.1 INTRODUCTION

1.2 TECHNICAL SPECIFICATIONS

1.2.1 ELECTRICAL ATTRIBUTES

1.2.2 PHYSICAL ATTRIBUTES

1.2.3 QUALIFICATIONS

SECTION 2 INSTALLATION CONSIDERATIONS

2.1 COOLING

2.2 EQUIPMENT LOCATION

2.3 ROUTING OF CABLES

2.4 LIMITATIONS

SECTION 3 INSTALLATION PROCEDURE

3.1 GENERAL INFORMATION

3.2 UNPACKING AND INSPECTING

3.3 CABLE HARNESS

3.3.1 WIRE GAUGE SELECTION

3.3.2 PIN ASSIGNMENT INFORMATION

3.3.3 HARNESS VERIFICATION

3.4 MOUNTING

3.5 INSTALLATION COMPLETION

SECTION 4 OPERATION

4.1 ELECTRICAL PERFORMANCE

4.2 PROTECTIVE FEATURES

SECTION 5 CONFORMANCE

5.1 CONTINUED AIRWORTHINESS STATEMENT

5.2 ENVIRONMENTAL QUALIFICATION STATEMENT

NUMBER LIST OF TABLES AND FIGURES

1.1 ELECTRICAL ATTRIBUTES TABLE

1.2 PHYSICAL ATTRIBUTES TABLE

1.3 PERFORMANCE TABLE

3.3 CONNECTOR PINOUT FIGURE

3.3 CONNECTOR PINOUT TABLE

3.4 EXAMPLE WIRING DIAGRAMS

3.5 TI1200 OUTLINE DRAWING FIGURE

4.1 TEMPERATURE PERFORMANCE

4.2 OUTPUT POWER VS VOLTAGE PERFORMANCE

4.3 OUTPUT POWER VS ALTITUDE PERFORMANCE

REV. B July 23, 2012 4 Manual Number 9017680

True Blue Power, Wichita, KS

SECTION 1 GENERAL DESCRIPTION

1.1 INTRODUCTION

The model TI1200 series Static Electrical Power Inverter is a lightweight power converter that translates
a 20 to 36 VDC input to a 115 VAC output at 60 Hertz and provides 1200 watts (VA) of power. The
alternating current output is defined as a pure sine wave with less than 2.5% of total harmonic distortion
for clean, noise-free, harmonic-free power to supply nearly any common commercial or consumer load
rated for a nominal input of 115VAC. The TI1200 series Inverter is FAA certified to TSO C73 and tested to
rigorous environmental standards and levels of RTCA DO-160. The small size and light weight in
conjunction with its installation flexibility (inside or outside the pressure vessel) make it an ideal choice
for aircraft power needs while reducing the challenges associated with other similar products.

Highlighted features include short circuit protection, overload capability, low voltage shut-down,
temperature monitoring, a self-resettable over-temperature disable, and a remote on/off function. The
rugged extrusion that houses the unit is designed to help dissipate heat and provide mechanical strength
against vibration or other possibilities of damage. Two independent fans allow for a smaller uni t and
provide a quieter operation while keeping the internal components cool and extending the life of the unit.

1.2 TECHNICAL SPECIFICATIONS

1.2.1 ELECTRICAL ATTRIBUTES

Characteristics:

Input Voltage: Rated 28VDC nominal; 20-36VDC certified; see figure 4.2
Input Power: 60 amps; 0.2A at no load
Output Voltage: 115VAC ±3% at 60 Hertz ±0.1% (single phase)
Output Power: 1200 watts (1200 VA at power factor = 1)
Output Waveform: Pure sine wave (less than 2.5% distortion)
Power Factor: -0.8 to +0.8
Efficiency: 88% nominal
Total Harmonic Distortion (THD): < 3%

Table 1.1

1.2.2 PHYSICAL ATTRIBUTES

Characteristics:

Weight: 7.25 pounds
Dimensions:
(not including connector mate)

Mating Connector (and cable clamp): MS3102A24-12S or equivalent (MCI P/N 9017235)
Mounting: Base mount – orientation not critical

1.2.3 QUALIFICATIONS

Specifications:

Qualification: FAA TSO-C73
Environmental Qualification: RTCA DO-160G Environmental Category

Altitude: -15,000 ft to +55,000 ft; See Figure 4.3
Temperature: -55°C to +70°C (-67°F to +158°F); See Figure 4.1

12.00 inches long

6.32 inches wide

3.45 inches high

Table 1.2

F3(Y)S2BB[(RCC1)(UG)]XXXXXXZXXXXXBXXXXX

Table 1.3

REV. B July 23, 2012 5 Manual Number 9017680