Font DIMM Printer / Font DIMM Kit Quick-Start Guide
READ ME FIRST
Installation Instructions for
TROY Font DIMM Printer and Font DIMM Kit
(For use with Hewlett-Packard LaserJet 1300, 1320, 2300, 4100, 4200, 4300, 8100, 8150, and 9000 Printers)
Introduction
Use the TROY Font DIMM Printer and Font DIMM Kit CD to install the required Hewlett-Packard LaserJet
printer drivers and TROY support files. To ensure successful installation of your TROY Font DIMM product,
perform the following steps in sequential order. The documentation and installation files contained on the
TROY Font DIMM Printer and Font DIMM Kit CD will be needed in the event that your printer is reinstalled
in a new location or after service has been performed.
Package Contents
• TROY Font DIMM
• TROY Font DIMM Printer and Font DIMM Kit CD
• TROY Security Printing Solutions Information Sheet
• TROY Software License Agreement
• TROY MICR Document Template
• TROY Font DIMM Kit User’s Guide (provided in PDF format on the CD)
• TROY Font DIMM Kit Installation Guide (provided in PDF format on the CD)
• TROY MICR Basics Handbook (provided in PDF format on the CD)
• TROY Font DIMM Printer and Font DIMM Kit Quick-Start Guide (this document)
STEP 1: Install the TROY MICR Toner Cartridge and TROY Font DIMM
1. Be sure to install a TROY MICR toner cartridge (purchased separately from TROY) in the same manner
as described for the standard Hewlett-Packard toner cartridge (refer to your Hewlett-Packard Getting
Started Guide for details). A MICR toner cartridge
MICR documents. For best results, TROY MICR toner cartridges are recommended. TROY’s highquality MICR toner is specifically designed for the MICR fonts contained on your TROY Font DIMM.
NOTE: If you purchased a TROY Font DIMM printer, skip the following step.
2. Install the TROY Font DIMM (supplied with your
TROY Font DIMM Solution) by using the TROY Font
DIMM Installation Guide provided in PDF format on
the TROY Font DIMM Printer and Font DIMM Kit
CD. The TROY Font DIMM
proceeding to Step #2 on the next page.
The Font DIMM is already installed in the printer.
must be installed before
must be installed in your printer in order to print
Document #50-70381-001 Rev. I Page 1 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
STEP 2: Install the HP PCL 5e Printer Driver for Microsoft
NOTE: Use only the TROY Font DIMM Printer and Font DIMM Kit CD to install the Hewlett-Packard
PCL 5e printer driver designated for your Hewlett-Packard printer. Some software screens may
differ slightly in appearance between operating systems.
NOTE: Some of the steps listed below may differ slightly depending on your operating system.
®
Windows
1. Close all applications before installing the HP PCL 5e printer driver.
2. Insert the TROY Font DIMM Printer and Font DIMM Kit CD into your computer CD drive.
3. Before beginning the installation process, you will need to know the operating system you are using on
your computer. If you already know the operating system you are using, proceed directly to step #4. If
you are not sure, right-click on My Computer (located on the Windows desktop), and then click on
Properties to view the type of operating system installed on your computer.
4. From the Start menu, click on Settings, and then click on Printers.
5. Double-click on Add Printer, click on Next, choose Local Printer, and then click on Next. If you are
using Windows 2000/XP, skip down to Step 12, and then proceed with Steps 6 through 11.
6. From the Add Printer Wizard window, click on Have Disk.
7. From the Install From Disk window, click on Browse.
8. From the Open window, click on the down-arrow in the Drives box to select the CD-ROM drive on
your computer.
™
9. Double-click on the appropriate folder for the operating system you are using (e.g., Win98, etc.).
10. Double-click on the appropriate subfolder for the model printer you are using (e.g., 4200, 9000). If
applicable for your model of printer, be sure to select either the USB or standard parallel (LPT1) printer.
Click on OK to close the Open window, and then click on OK to close the Install From Disk window.
11. Select the appropriate printer driver for you printer model, and then click on Next to continue the driver
installation. You will be given the choice to either replace or keep the existing driver. It is
recommended that you always replace the existing driver. Click on Next to continue. If you are using
Windows 2000/XP, skip down to Step 13.
NOTE: Two versions of the 2300 printer driver (2300 and 2300L) are contained on the TROY Font DIMM
Printer and Font DIMM Kit CD. Use only the 2300 printer driver when installing the TROY Font
DIMM. The 2300L printer driver does not support the TROY Font DIMM.
12. Select the appropriate printer port from the displayed list (usually LPT1), and then click on Next to
continue. If you are using Windows 2000/XP, go back and perform Steps 6 through 11 to complete the
driver installation. Otherwise, for Windows 98SE/ME operating systems, the printer name will be
highlighted.
13. For easy printer identification, it is recommended that you change the highlighted Hewlett-Packard
printer name to the name of the TROY printer you are installing (e.g., TROY MICR 4200 Printer) by
typing over the highlighted printer name. If you want to use this printer as your default printer, be sure
to select this printer as the default printer. If you are using Windows 2000/XP, choose to either share or
not to share your printer over the network.
14. Click on Yes to print a test page to verify that your printer driver was installed correctly, and then click
on Next to continue.
15. Click on Finish to complete the installation. The printer driver installation will proceed automatically
and add the printer icon to the printer folder.
Document #50-70381-001 Rev. I Page 2 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
STEP 3: Install the TROY
NOTE: The Hewlett-Packard PCL 5e printer driver must be installed on the host computer
prior to loading the TROY support files (refer to STEP 2 on the previous page).
Support Files for Microsoft® Windows
For 1320 Printer see page 5
™
The TROY metrics file contains the required escape sequences that are used to “call” the T ROY security and/or
optional barcode fonts installed in your TROY Security Printing Solution (via the TROY Font DIMM). When
properly installed, the TROY metrics file will be associated with the PCL 5e printer driver used by your
Hewlett-Packard printer to enable printing of the actual fonts installed in the printer. By associating the metrics
file with the printer driver, the TROY TrueType screen fonts will be automatically replaced with the actual
TROY fonts at print time. If the TROY metrics file is not properly installed, then the TROY TrueType screen
fonts will print instead of the actual TROY installed printer fonts.
Install the TROY Metrics File for Windows™ 98SE, ME, 2000, XP Operating Systems
1. Close all applications before installing the TROY Font support files.
2. Insert the TROY Font DIMM Printer and Font DIMM Kit CD into your computer CD-ROM drive.
3. From the Microsoft Windows Start menu, click on Settings, and then click on Printers.
4. Right-click on your HP printer icon, and then click on Properties from the pull-down menu. If multiple
printers are installed, make sure the correct printer icon is selected that corresponds to your HP printer.
5. Click on the Configure tab located at the top of the Properties window.
6. Within the Other Options category, click on the More button. Some printer driver versions may not
display the Other Options category. If this is the case, simply skip to the next step.
7. Within the Fonts category, place a check mark in the Font DIMMs checkbox, and then click on the
Configure button (with some printer driver software versions, the Configure button may already be
“clicked”). A new window will open labeled Configure Font DIMMs.
8. Click on the Add button to open the Add Font DIMM window.
9. Click on the Browse button to open a Windows Explorer-style window. Click on the down-arrow in the
Drives box to select the CD-ROM drive on your computer. Double-click on the Support Files folder
from the list of folders, double-click on the HPD Files folder, and then double-click on the Domestic
folder. For international products, double-click on the International folder.
10. Click on the file (located in the left-hand window) named TroySEC.hpd or TroySECINTL.hpd (for
International customers), and then click on Open or OK (the displayed window may vary depending on
the operating system being used). With some printer drivers, the Add Font DIMM window will appear.
If this window appears, click on OK to close the window.
11. Within the Configure Font DIMMs window, verify the installation by clicking on the Font DIMM
Name:
TROY Security Font Collection or TROY International Security Font Collection listed under
Installed DIMMs. Within the Fonts list, the TROY E-13B (enabled) along with other TROY fonts will
be displayed.
12. Repeat Steps 9 through 11 to install the barcode fonts. Double-click on the Support Files folder, the
HPD Files folder, and the Barcode folder, and then select the TroyBAR.hpd file. Verify the installation
by clicking on the Font DIMM Name:
TROY Barcode Font Collection listed under Installed DIMMs.
Within the Fonts list, the TROY barcode fonts will be displayed.
13. Close all remaining open windows. Please refer to the TROY Font DIMM Printer and Font DIMM Kit
User’s Guide, Section 3 – Using TROY Fonts before using the installed fonts.
Document #50-70381-001 Rev. I Page 3 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
Install the TROY Screen Fonts for Windows™ 98SE, ME, 2000, XP Operating Systems
In addition to the TROY printer fonts that are permanently programmed into your TROY Font DIMM, the
TROY screen fonts have been developed for display use only as a visual reference and for making
positional adjustments to the MICR line. The TROY screen fonts display differently than the actual printer
fonts to prevent unauthorized printing using the MICR screen fonts on other Windows-installed printers.
If the E-13B MICR screen font is used for printing, the inversely printed (white characters on black
background) MICR screen font will not be readable by the bank reader/sorter machines. The uniquely
displayed screen fonts ensure that the MICR font printed on your MICR documents is generated by a TROY
Security Printing Solution and
provided on the TROY Font DIMM Printer and Font DIMM Kit CD supplied with your TROY Font
DIMM Kit.
NOTE: Windows 2000/XP operating systems do not require installation of the TROY screen fonts.
1. Close all applications before installing the TROY support files.
2. Insert the TROY Font DIMM Printer and Font DIMM Kit CD into your computer CD-ROM drive.
3. From the Start menu, click on Settings, and then click on Control Panel.
4. Double-click on the Fonts folder icon.
not from a Windows TrueType™ screen font. The TROY screen fonts are
5. Click on File, and then click on Install New Font… A new window labeled Add Fonts will open and
then a Windows Explorer-style window will open.
6. Click on the down-arrow in the Drives box to select the CD-ROM drive on your computer. Double-
click on the Support Files folder from the list of folders, double-click on the HPD Files folder, and then
double-click on the Domestic folder. For international products, double-click on the International
folder.
7. A list of TROY fonts will be listed within the List of Fonts section. Click on Select All to highlight all
available fonts, and then click on OK. A processing window may appear while the installation process
proceeds. Individual fonts may be selected if all the fonts are not needed.
8. Repeat Steps 5 through 7 to install the barcode screen fonts. Double-click on the Support Files folder,
double-click on the HPD Files folder, and then double-click on the Barcode folder. Within the List of
Fonts section, click on Select All to highlight all available barcode screen fonts, and then click on OK.
A processing window may appear while the installation process proceeds.
9. Close all remaining open windows. The TROY screen fonts are now installed.
NOTE: For International customers, the International numeric fonts are not resident on the TROY
Font DIMM. These fonts are located on the TROY Font DIMM Printer and Font DIMM Kit CD in
the “\Support Files\HPD Files\International\Fonts” folder and can be added to the TROY Font
DIMM using the TROY Printer Utility – Download Soft Fonts Option. These fonts are designed
as non-scalable bitmapped fonts.
Document #50-70381-001 Rev. I Page 4 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
Install the TROY Metrics File for HP 1320 Model Printers Only
1. Close all applications before installing the TROY Font support files.
2. Insert the TROY Font DIMM Printer and Font DIMM Kit CD into your computer CD-ROM drive.
3. From the Microsoft Windows Start menu, click on Settings, and then click on Printers.
4. Right-click on your HP printer icon, and then click on Properties from the pull-down menu. If multiple
printers are installed, make sure the correct printer icon is selected that corresponds to your HP printer.
5. Click on the Device Settings tab located at the top of the Properties window.
6. Click on External Font (under the Font Substitution Table category), and then click on the Properties
button.
7. Click on the Browse button to open the drive selection window. Double-click on the appropriate drive
letter to select the CD-ROM drive on your computer.
8. Double-click on the Support Files folder from the list of folders, double-click on the PCM Files folder,
double-click on the Domestic folder, and then click on OK to close the drive selection window. For
international products, double-click on the International folder.
9. Use the SHIFT key to select all the fonts located in the left-hand window named TROY Auto-Protect,
TROY PCM7, etc., and then click on Add to add those fonts. If you want to add an individual font, just
highlight that specific font name and click on the Add button. All the added fonts should be displayed
in the right-hand window.
NOTE: If the barcode option was purchased, repeat Steps 8 through 10. Choose the TROY Barcode PCM
file from the Barcode folder.
10. Close all remaining open windows. Please refer to the TROY Font DIMM Printer and Font DIMM Kit
User’s Guide, Section 3 – Using TROY Fonts before using the installed fonts.
NOTE: Windows 2000/XP operating systems do not require installation of the TROY screen fonts.
Document #50-70381-001 Rev. I Page 5 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
STEP 4: Install the TROY
Software for Microsoft® Windows
™
Install the TROY Printer Utility for Windows™ 98SE, ME, 2000, XP, Server 2003
The TROY Printer Utility provides useful functions for testing your TROY Security Printing Solution
through Microsoft
allowing access to any printer installed in the Windows environment. The printer connection may be local,
network, or direct network connected. The TROY Printer Utility should be installed on the administrator’s
computer only. Some of the features of the TROY Printer Utility are provided for special applications and
may not be intended for general use. Refer to the TROY Font DIMM Printer and Font DIMM Kit User’s
Guide, Section 2 – Using the TROY Printer Utility for more information.
1. Close all applications before installing the TROY Printer Utility application.
2. Insert the TROY Font DIMM Printer and Font DIMM Kit CD into your CD-ROM drive.
3. From the Start menu, click on Run, and then click on Browse.
4. Click on the down-arrow in the Look In box at the top of the window, and then click on the drive letter
designated for the CD-ROM drive on your computer.
5. Double-click on the TROY Printer Utility folder.
6. Click on the file named setup.exe, click on Open, and then click on OK to start the installation process.
Follow the screen prompts to complete the installation.
NOTE: The TROY Printer Utility can be removed using the uninstall procedures located in Section 4 of the
®
Windows™. This utility takes advantage of the Windows-installed printer collection,
TROY Font DIMM Printer and Font DIMM Kit User’s Guide.
Document #50-70381-001 Rev. I Page 6 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
STEP 5: Test the TROY Font Support for Microsoft
®
Windows
™
To verify that the TROY Windows font support files were properly installed on your system, demonstration
documents are provided through the TROY Printer Utility in Windows that can be printed out to visually
identify all security and/or barcode fonts downloaded to your printer. Make sure your printer is properly setup,
powered ON, and is online before printing the Windows Security Font and/or Windows Barcode Font
Demonstration page(s).
TO PRINT THE TROY SECURITY FONT / BARCODE FONT DEMONSTRATION PAGE(S):
1. From the TROY Printer Utility
Main Window, click on the printer
you wish to manage, and then verify
that the correct TROY Security
Printing Solution is selected from
the drop-down list at the bottom of
the window.
2. From the Main Window, click on
File, Print, and then click on
Windows Security (MICR) Font
Demo. The printer will
automatically print the Windows
Security Font Demonstration page.
3. Compare the actual TROY security
fonts (the actual fonts generated by
your printing system) shown in the
right-hand column with the facsimile image of these fonts printed in the center column (a digitized image
designed to look exactly like the actual fonts correctly generated by your system – refer to the example
shown on the next page).
TROY Printer Utility
File Resources HelpSettings
Select the printer to configure from the following list:
HP 4200 PCL 5e LaserJet Printer LPT1:
Selected Printer Information
Admin Password
TROY Security Printing Solution
MICR Font DIMM Winspool
Selected printer location (port):
Windows Printer Driver
If the support files were properly installed, the actual TROY security and/or barcode fonts displayed in the
right-hand column should appear identical to the facsimile fonts displayed in the center column. If the
actual fonts do not match the facsimile fonts printed on the demonstration document (fonts not printed
correctly or fonts missing on the printout), review the installation steps in this document. If further
assistance is required, contact TROY Technical Support.
Accessing TROY Fonts Using Non-Windows Applications
If you are using a non-Windows application to print MICR documents, the escape sequence for each font must
be programmed into the application in order to “call” each of the selected fonts. The <Esc> character is ASCII
character number 27 (hexadecimal number 1B). Refer to Section 3 – Using TROY Fonts in the TROY Font
DIMM Printer and Font DIMM Kit User’s Guide for the specific escape sequence used to call each TROY font.
Document #50-70381-001 Rev. I Page 7 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
TROY Security Font Demonstration Page (not to scale)
NOTE: The TROY Microprint Font is not supported for the TROY Font Memory Card.
Document #50-70381-001 Rev. I Page 8 of 9
Font DIMM Printer / Font DIMM Kit Quick-Start Guide
Obtaining Technical Assistance
The TROY Printer Utility provides several help screens to guide you through the available features and
functions of your TROY Security Printing Solution. TROY technical support is available to assist you with any
questions concerning the setup, operation, and maintenance of your Security Printing Solution. Specific system
information about your TROY product configuration is available through the TROY Printer Utility. You are
also encouraged to visit the TROY web site for the latest FAQs (Frequently Asked Questions), information on
the latest TROY products, or for ordering MICR toner and other printing supplies.
TO VIEW TECHNICAL SUPPORT INFORMATION:
From the Main Window, click on Help, and then click on Technical Support to view the TROY Technical
Support HTML page for telephone numbers and hours of business.
TO VIEW INFORMATION ON THE TROY WEB SITE:
From the Main Window, click on Help, and then click on TROY on the Web to access the TROY web site.
Click on the Support and Downloads button at the top of the web page to view the available topics. You can
access the TROY web site directly from your web browser at
http://www.troygroup.com.
Reference Material
• TROY MICR Basics Handbook (provided on TROY Font DIMM Printer/Font DIMM Kit CD)
• TROY Font DIMM Installation Guide (provided on TROY Font DIMM Printer/Font DIMM Kit CD)
• TROY Font DIMM Kit User’s Guide (provided on TROY Font DIMM Printer/Font DIMM Kit CD)
• Hewlett-Packard Getting Started Guide (provided in the TROY Font DIMM Kit Startup Package)
• Hewlett-Packard Printer User’s Guide (provided on the Hewlett-Packard CD supplied with your printer)
Document #50-70381-001 Rev. I Page 9 of 9
Loading...