DIMM Installation Guide
TROY DIMM (Dual Inline Memory Module)
Installation Instructions
Follow the instructions specified for your model of Hewlett-Packard printer to install the TROY
DIMM. Click on the desired selection below to view the instructions for your HP printer.
• HP 1200 printer…………………………………………………. Page 2
• HP 1300 printer…………………………………………………. Page 4
• HP 1320 printer…………………………………………………. Page 6
• HP 2100 / 2200 printer……………………………………….… Page 8
• HP 2300 printer…………………………………………………. Page 11
• HP 4100 printer…………………………………………………. Page 14
• HP 4200 / 4300 printer………………………………….……… Page 16
• HP 8100 / 8150 printer………………………………….……… Page 18
• HP 9000 printer………………………………………….……… Page 20
• HP 2015 printer…………………………………………………. Page 22
Document #50-70395-001 Rev. D Page 1 of 22
DIMM Installation Guide
Hewlett-Packard 1200 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
1. Remove the printer paper tray to allow easier repositioning of the printer during the installation (Figure 1).
2. Open the toner cartridge access door at the front of the printer (Figure 2).
Figure 1 Figure 2
Unsnap the printer panel at the rear of the printer (Figure 3), swing the panel away from the printer, and then 3.
unhook and remove the panel from the printer to allow access to the DIMM slot (Figure 4).
Figure 3 Figure 4
Document #50-70395-001 Rev. D Page 2 of 22
CAUTION
4. Push the DIMM slot retaining
clips out to the side (Figure 5),
and remove the existing DIMM to
allow installation of the new
image DIMM. Ensure the DIMM
is positioned correctly (Figure 5),
and then fully insert the DIMM
into the DIMM slot until it snaps
into place (the white retaining
clips should close automatically).
5. Replace the printer panels, and
reconnect the printer power cord
and data cable.
6. Refer to the TROY Quick-Start
Guide (provided with your TROY
DIMM Solution) for instructions
on installing the required TROY
software and support files.
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Avoid touching any components or the metal contacts along the edge of the DIMM. Before
removing the DIMM from the anti-static bag, ground yourself by touching the metal portion of
the printer chassis to dissipate any static charge.
DIMM Installation Guide
Figure 5
NOTE: If assistance is required for removing or installing the DIMM, please call TROY Technical
Document #50-70395-001 Rev. D Page 3 of 22
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
DIMM Installation Guide
Hewlett-Packard 1300 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
1. Remove the printer paper tray to allow easier repositioning of the printer during the installation (Figure 1).
2. Open the toner cartridge access door at the front of the printer (Figure 2).
from the AC wall outlet.
Figure 1 Figure 2
Unsnap the printer panel at the rear of the printer (Figure 3), swing the panel away from the printer, and then
3.
unhook and remove the panel from the printer to allow access to the DIMM slot (Figure 4).
DIMM
Slot
Figure 3 Figure 4
ION
CAUT : The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Avoid touching any components or the metal contacts along the edge of the DIMM. Before
removing the DIMM from the anti-static bag, ground yourself by touching the metal portion of
the printer chassis to dissipate any static charge.
Document #50-70395-001 Rev. D
Page 4 of 22
4. Push the DIMM slot retaining
clips out to the side (Figure 5) to
allow installation of the DIMM.
Ensure the DIMM is positioned
correctly (Figure 5), and then fully
insert the DIMM into the DIMM
slot until it snaps into place (the
white retaining clips should close
automatically).
5. Replace the printer panels, and
then reconnect the printer power
cord and printer data cable.
6. Refer to the TROY Quick-Start
Guide (provided with your TROY
DIMM Solution) for instructions
on installing the required TROY
software and support files.
Figure 5
NOTE
: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
DIMM Installation Guide
Retaining
Clip
Notches in
edge of DIMM
must align with
tabs in the slot.
Document #50-70395-001 Rev. D
Page 5 of 22
DIMM Installation Guide
Hewlett-Packard 1320 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
1. Open the toner cartridge access door at the front of the printer (Figure 1).
2. Unsnap the printer panel at the rear of the printer by lifting the edge of the panel at the two small dimples
(Figure 2), swing the panel away from the printer, and unhook and then remove the panel from the printer to
allow access to the DIMM slot.
Figure 1
3.
Insert the font DIMM into the DIMM slot by aligning the notches in the DIMM with the tabs in the DIMM
socket (Figure 3 and Figure 4). Ensure the DIMM is seated properly (the retaining clips on the DIMM
socket should close automatically).
CAUTION: Use anti-static handling procedures to avoid
damaging the DIMM from static discharge.
Figure 3 Figure 4
Figure 2
Notches in DIMM
must align with tabs
in the DIMM socket.
Document #50-70395-001 Rev. D Page 6 of 22
4. Replace the printer side panel by hooking the tab on the right-hand edge of the panel into the slot on the
printer body (Figure 5 and Figure 6), and then swinging the panel toward the printer until it snaps into place.
DIMM Installation Guide
Figure 5 Figure 6
5. Reconnect the printer power cord and printer data cable.
6. Refer to the TROY Quick-Start Guide (provided with your TROY DIMM Solution) for instructions on
installing the required TROY software and support files.
NOTE: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Document #50-70395-001 Rev. D Page 7 of 22
DIMM Installation Guide
Hewlett-Packard 2100 / 2200 Printers:
IMPORTANT
1. Depress the two buttons located at the rear of the printer, and pull the cover open (Figures 1 and 2).
: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
Figure 1
. Unhinge the cover, and remove the cover from the printer (Figure 3).
2
Figure 3
Figure 2
Document #50-70395-001 Rev. D Page 8 of 22
DIMM Installation Guide
3. Open the toner compartment door, depress the interlock button on top of the printer (Figure 4), and then
slide the printer panel forward about ½ of an inch. Pull panel away from printer (Figure 5).
Figure 4 Figure 5
CAUTION: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Handle the DIMM by the edges only. Avoid touching any of the components on the DIMM or the
metal contacts along the edge of the DIMM. Before removing the DIMM from the anti-static-bag,
4. Ensure the DIMM is positioned correctly (Figure
6), and then fully insert the DIMM into the
DIMM socket until the DIMM snaps into place
(retaining clips should be closed).
ground yourself by touching the metal portion of the printer chassis to dissipate any static charge.
The DIMM is keyed and can only be inserted when the
two notches are aligned with the tabs in the DIMM slot.
TROY DIMM
Place DIMM into the DIMM slot, then push firmly
at each corner until the DIMM snaps into place.
Figure 6
5. Replace the printer panels, and then reconnect the printer power cable to the AC wall receptacle.
Document #50-70395-001 Rev. D Page 9 of 22
DIMM Installation Guide
6. Refer to the TROY Quick-Start Guide for instructions on installing the required software and support files.
NOTE: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Document #50-70395-001 Rev. D
Page 10 of 22
DIMM Installation Guide
Hewlett-Packard 2300 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
1. Depress the two buttons located at the rear of the printer, and pull the cover open (Figures 1 and 2).
2. Unhinge the cover, and remove the cover from the printer (Figure 3).
from the AC wall outlet.
Figure 1
Figure 3
NOTE
: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Figure 2
Document #50-70395-001 Rev. D
Page 11 of 22
DIMM Installation Guide
3. Open the toner compartment
door, depress the interlock
button on top of the printer
(Figure 4), and then slide the
printer panel forward about ½
of an inch. The panel should
easily pull away and detach
from the printer (Figure 5).
Depress the
interlock button,
then slide panel
forward about
1/2 of an inch.
Figure 4 Figure 5
CAUTION
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Avoid touching any components or the metal contacts along the edge of the DIMM. Before
removing the DIMM from the anti-static bag, ground yourself by touching the metal portion of
the printer chassis to dissipate any static charge.
4. Verify the DIMM slot retaining clips are pushed out to the side to allow installation of the Font DIMM.
Ensure the Font DIMM is positioned correctly (Figures 6 and 7), and then fully insert the DIMM into one of
the available DIMM slots until it snaps into place (the retaining clips should close automatically).
Figure 6 Figure 7
5. Replace the printer panels, and then reconnect the printer power cord and printer data cable.
Document #50-70395-001 Rev. D Page 12 of 22
DIMM Installation Guide
6. Refer to the TROY Quick-Start
installing the required TROY soft
Guide (provided with your TROY DIMM Solution) for instructions on
ware and support files.
Document #50-70395-001 Rev. D Page 13 of 22
DIMM Installation Guide
Hewlett-Packard 4100 Series Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
1. Unsnap and slide the right-rear panel toward the rear of the printer (Figure 1).
2. Open the DIMM access door (Figure 2). For easier access, the metal door can easily be removed by lifting
the door off the hinge slots.
Figure 1
CAUTION
. Verify the DIMM slot retaining clips are pushed out to the side to allow
3
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Avoid touching any components or the metal contacts along the edge of the DIMM. Before
removing the DIMM from the anti-static bag, ground yourself by touching the metal portion
the printer chassis to dissipate any static charge.
Figure 2
installation of the DIMM. Ensure the DIMM is positioned correctly (Figures 3
and 4), and then fully insert it into either DIMM slot #2 or #3 until it snaps into
place (the retaining clips will close automatically). Do not remove or change the
position of any DIMMs installed in DIMM slots #0 or #1.
of
Figure 4 Figure 5
Document #50-70395-001 Rev. D Page 14 of 22
. Close the DIMM access door, replace printer panels, and reconnect the power cord and printer data cable.
4
5. Refer to the TROY Quick-Start Guide for instructions on installing the required software and support files.
DIMM Installation Guide
Document #50-70395-001 Rev. D Page 15 of 22
DIMM Installation Guide
Hewlett-Packard 4200 / 4300 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
1. Unsnap and slide the right-rear panel toward the rear of the printer (Figure 1).
2. Pull open the DIMM access door (Figure 2). The metal door can easily be removed by lifting the door off
the hinge slots.
from the AC wall outlet.
Open the DIMM
access door.
Slide panel toward
rear of the printer.
Figure 1
CAUTION
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Handle the DIMM by the edges only. Avoid touching the components on the DIMM or the meta
contacts along the edge of the DIMM. Before removing the DIMM from the anti-static bag,
ground yourself by touching the metal portion of the printer chassis to dissipate static charge
Figure 2
.
. Ensure the retaining clips on the empty DIMM slot are pushed out to the side (Figure 3 and Figure 4) to
3
allow installation of the TROY Font DIMM.
l
Push the retaining clips out to the side.
Document #50-70395-001 Rev. D Page 16 of 22
Figure 3 Figure 4
4. Ensure the TROY Font DIMM is oriented correctly (Figure 5), fully insert the
DIMM into DIMM slot #2 (Figure 6), and then push firmly on each corner of the
DIMM until the DIMM snaps into place. The retaining clips will close
automatically. Verify the DIMM retaining clips are closed (retaining clips
pressed against the DIMM) to ensure the DIMM is properly seated in the DIMM
slot. Do not
remove or change the slot location of any existing DIMMs.
DIMM Installation Guide
Base Firmware
Base RAM
TROY DIMM
(unused slot)
4200/4300 DIMM Configuration
0
1
2
3
The DIMM is keyed and can only be inserted when the
two notches are aligned with the tabs in the DIMM slot.
TROY DIMM
Place DIMM into the DIMM slot, then push firmly
at each corner until the DIMM snaps into place.
Insert the TROY Font DIMM in this slot.
Figure 5 Figure 6
5. Close the DIMM access door, and replace the printer panels.
6. Reconnect the printer power cord and printer data cable.
7. Refer to the TROY Quick-Start Guide (provided with your TROY DIMM Solution) for instructions on
installing the required TROY software and support files.
NOTE
: If assistance is required for installing the TROY DIMM, please call TROY Technical Support
at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Document #50-70395-001 Rev. D Page 17 of 22
A
DIMM Installation Guide
Hewlett-Packard 8100 / 8150 Series Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
1. Loosen the thumbscrews (turn counter-clockwise) at rear of the printer (Figure 1 and Figure 2), and then
carefully slide the formatter board out of printer (Figure 3).
Figure 1 e 3
2. Set the formatter board on a clean flat surface. Ensure the retaining clips for one of the empty DIMM slots
are pushed out to the side to allow installation of the TROY DIMM. Do NOT remove or change the slot
location of any currently installed DIMM. Use one of the currently empty DIMM slots only.
Install the DIMM into one of the available DIMM slots in the correct orientation, matching3.
the DIMM with the tabs at the bottom of the DIMM slot (Figure 4 and Figure 5).
Figure 2 Figur
the cutouts in
CAUTION
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Handle the DIMM by the edges only. Avoid touching the components on the DIMM or the
metal contacts along the edge of the DIMM. Before removing the DIMM from the anti-stati
ground yourself by touching the metal portion of the printer chassis to dissipate any static charge.
c-bag,
lign notches in the font DIMM with
the tabs at the bottom of DIMM slot.
Figure 4 Figure 5
Document #50-70395-001 Rev. D
Page 18 of 22
DIMM Installation Guide
4. Ensure the DIMM is positioned correctly, and then fully insert the DIMM into the DIMM slot until the
DIMM snaps firmly into place (Figure 6). The retaining clips will close automatically. Verify the DIMM
retaining clips are fully closed.
The DIMM is keyed and can only be inserted when the
two notches are aligned with the tabs in the DIMM slot.
TROY DIMM
Place DIMM into the DIMM slot, then push firmly
at each corner until the DIMM snaps into place.
Figure 6
5. Align top and bottom edges of the formatter board with the top and bottom track guides inside the printer
(Figure 7 and Figure 8), and carefully slide the formatter board into the printer. Hand-tighten the two
thumbscrews (turn clockwise) on the formatter board.
Correct installation of the font DIMM
with the retaining clips pushed closed.
Figure 7 Figure 8
6. Reconnect the printer data cable and power cable. The font DIMM installation is complete.
7. Refer to the TROY Quick-Start Guide (provided with your TROY DIMM Solution) for instructions on
installing the required TROY software and support files.
NOTE: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Document #50-70395-001 Rev. D
Page 19 of 22
DIMM Installation Guide
Hewlett-Packard 9000 Series Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord
from the AC wall outlet.
1. Loosen the two thumbscrews (turn counter-clockwise) at the rear of the printer (Figure 1 and Figure 2), and
then carefully slide the formatter board out of the printer (Figure 3).
Carefully slide the
formatter board
out of the printer.
Figure 1
Figure 2 Figure 3
. Set the formatter board on a clean flat surface. Ensure the retaining clips for one of the available DIMM
2
slots are pushed out to the side to allow installation of the TROY DIMM. Do NOT remove or change the
slot location of any currently installed DIMM. Use one of the currently empty DIMM slots only.
Install the DIMM into one of the available DIMM slots in the correct orientation, matching the3.
cutouts in
the DIMM with the tabs at the bottom of the DIMM slot (Figure 4 and Figure 5).
CAUTION
: The DIMM is a static-sensitive device and can be permanently damaged if handled improperly.
Handle the DIMM by the edges only. Avoid touching the components on the DIMM or the meta
contacts along the edge of the DIMM. Before removing the DIMM from the anti-static-bag, groun
yourself by touching the metal portion of the printer chassis to dissipate any static charge.
Align notches in the font DIMM with
the tabs at the bottom of DIMM slot.
l
d
Document #50-70395-001 Rev. D
Figure 4 Figure 5
Page 20 of 22
4. Ensure the DIMM is positioned correctly, and then fully insert the DIMM into the DIMM slot until the
DIMM snaps firmly into place (Figure 6). The retaining clips will close automatically. Verify the DIMM
retaining clips are fully closed.
The DIMM is keyed and can only be inserted when the
two notches are aligned with the tabs in the DIMM slot.
TROY DIMM
Place DIMM into the DIMM slot, then push firmly
at each corner until the DIMM snaps into place.
Figure 6
DIMM Installation Guide
Correct installation of the font DIMM
with the retaining clips pushed closed.
5. Align the top and bottom edges of the formatter board with top and bottom track guides inside the printer
(Figure 7 and Figure 8), and carefully slide the formatter board into the printer. Hand-tighten the two
thumbscrews (turn clockwise) on the formatter board.
Align the edge of the formatter board with the
track guides, and push the board into the printer.
Figure 7 Figure 8
6. Reconnect the printer data cable and power cable. The font DIMM installation is complete.
7. Refer to the TROY Quick-Start Guide (provided with your TROY DIMM Solution) for instructions on
installing the required TROY software and support files.
NOTE
: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Document #50-70395-001 Rev. D
Page 21 of 22 Document #50-70395-001 Rev. D Page 21 of 22
DIMM Installation Guide
Hewlett-Packard 2015 Printers:
IMPORTANT: Ensure the printer power is switched OFF, and then disconnect the printer power cord from the
printer. Never install or remove the DIMM when the printer power is ON!
1. Open the DIMM access door at the left side of the printer using your finger to press and unlatch the door
(Figure 1).
2. Detach the DIMM access door from the printer by fully opening
the door and then unhooking the two hinge tabs from the printer
panel.
IMPORTANT: To prevent static discharge from damaging the TROY
Font DIMM, handle the DIMM by the edges and avoid touching the
metal contacts on the edge of the DIMM.
3. Remove the TROY Font DIMM from the protective anti-static
bag.
Figure 1
4. Insert the DIMM into the DIMM slot by aligning the notches in the DIMM with the tabs in the DIMM
Figure 2
socket. The DIMM can only be inserted in one orientation.
5. Ensure the DIMM is fully inserted into the DIMM socket, and then carefully press on each corner of the
DIMM (Figure 2) until the metal retaining clips snap over the edges of the DIMM (Figure 3).
6. Replace the access door by aligning the hinge tabs with the notches in the printer panel, and then push the
access door closed until it snaps into place.
7. Reconnect the printer power cord, and then switch the printer power ON.
8. Refer to the TROY Font DIMM Printer and Font DIMM Kit Quick-Start Guide for instructions on installing
the TROY support files on your computer. If assistance is required, call TROY Technical Support at (800)
332-6427. Customers outside the United States, please call (304) 232-0899
NOTE: If assistance is required for removing or installing the DIMM, please call TROY Technical
Support at (800) 332-6427. Customers outside the United States, please call (304) 232-0899.
Figure 3
Document #50-70395-001 Rev. D Page 22 of 22
Loading...