Troy-Bilt 560 Series Operator's Manual

Operator's Manual

21" Three-in-One

Self Starter

Self-Propelled

Mower

Model

560 Series

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush*covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

TROY-BILTLLC, P.O.BOX361131CLEVELAND,0HI0 44136-0019

PRINTED IN U.S.A. FORM NO. 769-00006B

ECO No.

(2/2002)

TABLEOFCONTENTS

Content Page

Important Safe Operation Practices ................................................................... 3

Slope Gauge ...................................................................................................... 6

Assembling Your Lawn Mower ........................................................................... 7

Know Your Lawn Mower .................................................................................... 9

Operating Your Lawn Mower ............................................................................. 10

Making Adjustments .......................................................................................... 12

Maintaining Your Lawn Mower ........................................................................... 13

Off-Season Storage ........................................................................................... 16

Troubleshooting ................................................................................................. 17

Parts List ............................................................................................................ 18

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new lawn mower, It wilt help you assemble, prepare and
maintain the unit for best performance, Please read and understand what it says,

Before you start assembling your new equipment, please locate the model plate on the
equipment and copy the information from it in the space provided below. The information on
the model plate isvery important if you need help from our Customer Support Department or

an authorized Service dealer.

You can locate the model number by standing at the operating position and looking down at the rear
of the mower. A sample model plate is explained below. For future reference, please copy the model
number and the serial number of the equipment in the space below.

(Model Number) (Serial Number)

3311_tttfi1!1_'1_I1_I

, inlu4,1e-_j

Copy the model number here:

Copy the serial number here:

ENGINEINFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-
rating, specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's

Manual packed separately with your unit for more information.

CALLINGCUSTOMERSUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, please call the Customer Support Department,

Call 1- [phone] or 1-(866)-840-6843 to reach a Customer Support representative.
Please have your unit's model number and serial number ready when you call. See previous

section to locate this information. You will be asked to enter the serial number in order to
process your call.

2

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING: This symbol points out important safety instructionswhich, ifnot followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal

injury. When you see this symbol--HEED ITS WARNING.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit

chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with

any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This
machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instruc-
tions could result in serious injury or death.

GeneralOperation

1. Read this operator's manual carefully in its entirety
before attempting to assemble this machine. Read,

understand, and follow all instructions on the machine

and in the manual(s) before operation. Be completely
familiar with the controls and the proper use of this

machine before operating it. Keep this manual in a safe
place for future and regular reference and for ordering
replacement parts.

2. This machine is a precision piece of power equipment,
not a plaything. Therefore, exercise extreme caution at all

times. Your unit has been designed to perform one job: to

mow grass. Do not use it for any other purpose.

3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent. Only responsible individuals who are familiar with

these safe operation rules should use this machine.

4. Thoroughly inspect the area where the equipment is to
be used. Remove all stones, sticks, wire, bones, toys and

other foreign objects which could be tripped over or

picked up and thrown by the blade. Thrown objects can

cause serious personal injury. Plan your mowing pattern
to avoid discharge of material toward roads, sidewalks,

bystanders and the like. Also, avoid discharging material

against a wall or obstruction which may cause discharged

material to ricochet back toward the operator.

5. To help avoid blade contact or athrown object injury, stay
in the operator zone behind the handles and keep
bystanders, helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop machine if
anyone enters the area.

6. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

7. Wear sturdy, rough-soled work shoes and dose-fitting

slacks and shirts. Shirts and pants that cover the arms
and legs and steel-toed shoes are recommended. Never
operate this machine in bare feet, sandals, slippery or

light weight (e.g. canvas) shoes.

8. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade can amputate hands
and feet.

9. A missing or damaged discharge cover can cause blade
contact or thrown object injuries.

10. Many injuries occur as a result of the mower being pulled
over the foot during a fall caused by slipping or tripping.
Do not hold on to the mower if you are failing; release the
handle immediately.

11. Never pub the mower back toward you while you are
walking. If you must back the mower away from a wall or
obstruction first look down and behind to avoid tripping
and then follow these steps:

a. Step back from the mower to fully extend your

arms.

b. Be sure you are web balanced with sure footing.

c. Pull the mower back slowly, no more than half way

toward you.

d. Repeat these steps as needed.

12. Do not operate the mower while under the influence of

alcohol or drugs.

13. Do not engage the self-propelled mechanism on units so

equipped while starting engine.

14. The blade control handle is a safety device. Never

attempt to bypass its operation. Doing so makes the
safety device inoperative and may result in personal
injurythrough contact with the rotating blade. The blade
control handle must operate easily in both directions and
automatically return to the disengaged position when

released.

15. Never operate the mower in wet grass. Always be sure of

your footing. A slip and fall can cause serious personal
injury. If you feel you are losing your footing, release the
blade control handle immediately and the blade will stop
rotating within three seconds.

16. Mowin daylightor good artificiallight. Walk, never run.

17. Stop the blade when crossing gravel drives, walkways

or roads.

18. If the equipment should start to vibrate abnormally, stop

the engine and check immediately for the cause.
Vibration is generally a warning of trouble.

19. Shut the engine off and wait until the blade comes to a

complete stop before removing the grass catcher or
unclogging the chute. The cutting blade continues to
rotate for a few seconds after the engine is shut off.
Never place any part of the body in the blade area until
you are sure the blade has stopped rotating.

20. Never operate mower without proper trail shield,
discharge cover, grass catcher, blade control handle or

3

othersafetyprotectivedevicesinplaceandworking.
Neveroperatemowerwithdamagedsafetydevices.
Failuretodeso,canresultinpersonalinjury.

21.Mufflerandenginebecomehotandcancauseaburn.Do
nottouch.

22.Only use parts and accessories made for this machine by

the original equipment manufacturer (O.EM). Failure to
do so can result in personal injury.

23. If situations occur which are net covered in this manual,
use care and good judgment. Contact your dealer for

assistance. Telephone [phone] for the name of
your nearest dealer.

SlopeOperation

Slopes are a major factor related to slip and fall accidents
which can result in severe injury. Operation on slopes
requires extra caution. If you feel uneasy on a slope, do not
mow it. Before operating this unit on a slope or hilly area, use
the slope gauge on page 6 to measure slopes. Ifthe slope is
greater than 15 degrees, do not mow it.

DO:

1. Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction on
slopes.

2. Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide

obstacles.

3. Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your
balance, release the blade control handle immediately,
and the blade will stop rotating within 3 seconds.

Do Not:
f. Do not mow near drop-offs, ditches or embankments,

you could lose your footing or balance.

2. Do not mow slopes greater than 15 degrees as shown on
the slope gauge.

3. De net mow on wet grass. Unstable footing could cause
slipping.

Children

Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
mower and the mowing activity. They do not understand the
dangers. Never assume that children will remain where you

last saw them.

1. Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.

2. Be alert and turn mower off if a child enters the area.

3. Before and while moving backwards, look behind and
down for small children.

4. Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may
obscure your vision of a child who may run into the

mower.

5. Keep children away from hot or running engines. They
can suffer burns from a hot muffler.

6. Never allow children under 14 years old to operate a

power mower. Children 14 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained and
supervised by a parent.

Service

Safe Handling OfGasoline:

1. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious

personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite.

2. Wash your skin and change clothes immediately.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on atruck or
trailer bed with a plastic liner. Always place containers on

the ground away from your vehicle before filling.

5. If possible, remove gas-powered equipment from the
truck or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dispenser

nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.

7. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.

8. Never fuel machine indoors because flammable vapors
will accumulate in the area.

9. Never remove gas cap or add fuel while the engine is hot
or running. Allow engine to cool at least two minutes
before refueling.

10. Neveroverfillfueltank. Fill tank to no mere than ½ inch
below bottom of filler neck to provide space for fuel

expansion.

11. Replace gasoline cap and tighten securely.

12. If gasoline is spilled, wipe it off the engine and
equipment. Move unit to another area. Wait 5 minutes
before starting the engine.

13. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light as on a water

heater, space heater, furnace, clothes dryer or other gas
appliances.

14. To reduce fire hazard, keep mower free of grass, leaves,
or other debris build-up. Clean up oil or fuel spillage and
remove any fuel soaked debris.

15. Allow a mower to cool at least 5 minutes before storing.

GeneralService:

1. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.

2. Before cleaning, repairing, or inspecting, make certain
the blade and all moving parts have stopped. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.

3. Check the blade and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade

for damage (e.g., bent, cracked, worn) Replace blade

with the original equipment manufacture's (O.E.M) blade
only, listed in this manual. "Use of parts which do not

4

meettheoriginalequipmentspecificationsmayleadto
improperperformanceandcompromisesafety!"

4. Mowerbladesaresharpandcancut.Wrapthebladeor
weargloves,anduseextracautionwhenservicingthem.

5. Keepallnuts,bolts,andscrewstighttobesurethe
equipmentisinsafeworkingcondition.

6. Nevertamperwithsafetydevices.Checktheirproper
operationregularly.

7. Afterstrikingaforeignobject,stoptheengine,disconnect
thesparkplugwireandgroundagainsttheengine.
Thoroughlyinspectthemowerforanydamage.Repair
thedamagebeforestartingandoperatingthemower.

8. Neverattempttomakeawheelorcuttingheight
adjustmentwhiletheengineisrunning.

9. Grasscatchercomponents,dischargecover,andtrail
shieldaresubjecttowearanddamagewhichcould
exposemovingpartsorallowobjectstobethrown.For
safetyprotection,frequentlycheckcomponentsand

replaceimmediatelywithoriginalequipment
manufacturer's(O.EM.)partsonly,listedinthismanual
"Useofpartswhichdonotmeettheoriginalequipment
specificationsmayleadtoimproperperformanceand
compromisesafety!"

10.Donotchangetheenginegovernorsettingoroverspeed
theengine.Thegovernorcontrolsthemaximumsafe
operatingspeedoftheengine.

11.Maintainorreplacesafetyandinstructionlabels,as
necessary.

12.Observeproperdisposallawsandregulations.Improper
disposaloffluidsandmaterialscanharmthe

environment.

13.ALWAYSde-energizeselfstarterpriortoperformingany
maintenanceorservicetotheengineandormower.
Followinstructionsbothinmanualandontheengineand
ormachinetode-energizestarter.

YourResponsibility

Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in

this manual and on the machine.

DANGER

5

USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

A POWER POLE

A CORNER OF A BUILDING

ORA FENCE POST

|

I

15°

WARNING _

¢0

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A
riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is
extremely difficult to maintain your footing and you could slip, resulting in serious injury.
Operate RIDING mowers up and down slopes, never across the face of slopes.
Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes.

SECTION3: ASSEMBLINGYOURLAWNMOWER

ToRemoveUnit FromCarton

Remove staples, break glue on top flaps, or cut tape
at carton end and peel along top flap to open carton.
Remove loose parts included with your unit (i.e.,
operator's manual, etc.).
Cut along corners and lay carton down flat.
Remove packing material.

Roll or slide unit out of carton.

HardwarePack

1. Carriage Bolt 1/4-20 x.75" (2)

2. Wing Nut with Bell Washer (2)

ToolsRequired

1. Pair of Pliers

2. Funnel
NOTE: Reference to right or left hand side of the mower

is observed from the operating position.

DisconnectingSparkPlug

Before setting up your lawn mower, disconnect the
spark plug wire from the spark plug, and ground it
against the engine. See Figure 1.

_-Spark Plug

Figure I

AssemblingHandle

For shipping purposes, the grass bag was placed
on top of the unit. Remove it from the unit and set it
out of the way. See Figure 2.

2. Lift lower
handle 1.Move bag

away

3. Lift upper
handle

Raise the lower handle, as shown in Figure 2, till it

snaps into place.

Raise the upper handle as shown in Figure 2.
Tighten the two wing nuts which are already on the
handle. See Figure 3.

Assembly

Nuts

Figure 3

NOTE: Make sure to route the cables outside the lower

handle. Also de not crimp the cables while lifting the
handle up.

Place rear wheels in the highest height position
using the rear height adjustment lever.
Remove the hairpin clips from the outer hole in the

weld pins on the handle mounting brackets. Using a

pair of pliers, squeeze one leg of the lower handle

against the handle mounting bracket. Insert the

hairpin clip into the inner hole on the weld pin.
Repeat on the other side. See Figure 4.

_, _, Handle Mounting

F_----_/Bracket

\\'_'hk,_,_ Insert hairpin

"_ _ ((((e"_ clip here

Hairpin \ \\ "ll\_

"_'_'J _© _'_ Weld

_ Pin

Figure 4

Insert post of cable ties that are on lower handle
intothe holes provided on the lower handle. The
holes may be on the inside oroutside. Pull cable

ties tight and cutoff the extra. See Figure 5.

NOTE: Holes can be on the inside or outside of the

handle.

Cable Tie

Post on

Figure 2

Figure 5

7

AttachingStarter Rope

The rope guide is already attached to the right side of
the lower handle of your mower.

The rope guide is attached to the right side of upper
handle. Loosen the wing nut which secures the

rope guide. See Figure 6.
With spark plug wire disconnected and grounded,

hold the blade control handle against the upper
handle, and pull the starter rope out of the engine.

Release blade control handle. Slip the rope into the
rope guide. Tighten the wing nut. See Figure 6.

Slip rope into

rope gu_/,_ jing Nut

Figure 6

Tighten all nuts and bolts securely.
After you have moved the hairpin clips as shown in

Figure 4, place one carriage bolt (found in the
hardware pack included with your unit) in the upper

hole of the right handle mounting bracket from the
inside outward. See Figure 7. Secure with one

plastic wing nut. Repeat process on the left side

Figure 7

AttachingGrassCatcherToMower

NOTE: The mulching baffle is already in place on the
mower for shipping purposes. Your lawn mower is
equipped with both a mulching baffle and a mulching
plug. While the mulching baffle is located at the rear of
the mower, the mulching plug is located on the right
side of the cutting deck. De not remove the mulching
plug from the mower even when you are not mulching
the grass.

To remove the mulching baffle, lift the rear

discharge door on the mower. Remove the

mulching baffle. See Figure 8.

Figure 8

IMPORTANT: Make sure cables are routed to the
outside ofthe handle so they are not in the way when

attaching the grass catcher.

Liftthe rear discharge door on the mower.
Place the hooks, found on both sides of the grass

catcher frame, over the chute door pivot rod at the

rear ofthe mower. See Figure 9. Release the rear

discharge door.

To remove the grass catcher, lift the rear

discharge door on the mower. Lift the grass catcher

up and off the pivot rod. Reinstall the mulching
baffle and release the rear discharge door. See
Figure 9.

WARNING: Never operate the mower

unless the hooks on the grass catcher are

firmly seated on the chute pivot rod, and the

rear discharge door rests firmly against the

top of the grass catcher.

Discharge Door

8

Figure 9

ConvertingTo SideDischarge

Lift the rear discharge door and install the mulching
baffle. See Figure 8.
On the side of the mower, lift the mulching plug.
See Figure 10.
Slide the two hooks of the side discharge chute
under the hinge pin on the mulching plug assembly

as shown in Figure 10. Lower the side mulching

plug.

Donotremovethesidemulchingplugatanytime,
evenwhenyouarenotmulching. Mulching Plug

,/

Hinge !

J f

(Slide hooks under tl

sides of hinge pin)

Figure 10

SECTION4: KNOWYOURLAWNMOWER

Lower Bail Handle

Control Button

Control Handle

WARNING: The blade control handle is a

safety device. Never attempt to bypass its
operations. Doing so, may result personal
injury through contact with the rotating blade.
The blade will rotate whenever the engine is
running and when the self starter is de-
energized.

Grass Bag/Fill Indicator

Cutting Height
Adjustment Lever

Recoil
Starter

Mulching
Plug

Safet'

Figure 11

_lb WARNING: Be familiar with all controls

and their proper operation. Know how to stop
the machine and disengage them quickly.

Blade Control Handle
The blade control handle is located on the upper handle

of the mower. The blade control handle and starter
control button must be depressed in order to operate
the unit. Release blade control handle to stop engine

and blade and to energize the self starter. See Figure

11.

Lower Bail Handle
The lower bail handle is located on the upper handle

and is used to engage the drive. Squeeze the bail
handle against the upper handle to engage the drive;
release it to slow down or stop the mower from
propelling. See Figure 11.

Recoil Starter
he recoil starter is attached to the right lower handle.

The recoil starter is used to start the engine when the
self starter is in the de-energized mode. See.

Cutting Height Adjustment Lever
This lever, located at each wheel, lets you adjust cutting

height of the grass. Remember to put all four levers at
the same height to avoid uneven cut. See Figure 11.

Mulching Plug
Both the mulching baffle and the mulching plug are

used only for mulching purposes. Instead of collecting
the grass clippings in a grass catcher, your mower has
the option of recirculating the clippings back to the
lawn. This is called mulching.

Throttle Speed
Your lawn mower engine is equipped with a constant

speed throttle, which is set at full throttle for best
performance.

9

Safety Key
The safety key is located on the engine. See Figure 11.

The safety key is a safety device used to activate and
deactivate the self starter system. The self starter
system will not work without the key in it's proper
position. See your engine manual for more information
on the safety key. See Figure 11.

NOTE: The safety key must be in the run position to

start the mower for both systems, either the self starter
or recoil starter.

Start Control Button
The start control button is located on the upper left side

of the upper handle. See Figure 11. The start control
button must be depressed fully while pulling the blade
control handle toward upper handle for the engine to

start. The starter control button will automatically return
to the off/up position once the blade control handle is
released. See Figure 11.

The starter control button must be depressed to start

the engine either with the self starter or recoil starter
system.

Grass Bag Fill Indicator
The grass bag is equipped with a bag-fill indicator to

add convenience to your work. While the mower is
running, air wilt flow through the bag and into the "sail."
If the grass catcher is empty, air flows through easily
pushing the sail up. If the grass catcher is full, air does
not flow through it allowing the sail to fall. So the
position of the sail acts as a bag-fill indicator signifying
when to empty the grass bag. See Figure 11.

SECTION5: OPERATINGYOURLAWNMOWER

WARNING: Be sure no one other than the

operator is standing near the lawn mower
while starting engine or operating mower.

WARNING: Never run engine indoors or in

enclosed, poorly ventilated areas. Engine
exhaust contains carbon monoxide, an

odorless and deadly gas.

WARNING: Keep hands, feet, hair and

loose clothing away from any moving parts

on engine and lawn mower.

GasandOil Fill-Up

Service the mower engine with gasoline and oil
following instructions in the engine manual. If your
mower was shipped with oil in the engine, fill up the
required amount of gasoline only. Always make
sure there is adequate oil in the engine before
starting the engine.

WARNING: Never fill fuel tank indoors,

with engine running or until the engine has
been allowed to coot for at least two minutes

after running.

AdjustingCuttingHeight

Your mower was shipped at the highest cutting
height. For best results in mowing, keep the cutting
height position high until it is determined which
height is best for your lawn.
Refer to height adjustments section of this manual
on page 12for instruction on how to adjust the
cutting height and the handle height.

BeforeStartingMower

Attach spark plug wire to spark plug. Make certain

the metal cap on the end of the spark plug wire

(inside the rubber boot) is fastened securely over

the metal tip on the spark plug.

FirstTimeStartingEngine

NOTE: Use recoil starter rope to start engine for the

very first time. The mower is shipped with the safety key
in the locked position and the self starter in the de-
energized mode, follow instructions as follows:

1. Place lawn mower on a level surface outdoors.

2. Remove plastic wrap under fuel cap.

3. Check oil level.

4. Add fuel.

5. Open shut off valve (if equipped) 1/4 turn.

6. Push spark plug wire firmly on spark plug.

7. Turn self starter safety key 1/4 turn clockwise to
RUN position.

8. Firmly push primer bulb 3 times.

9. While standing at upper handle, depress the starter
control button fully with the thumb of your right

hand.

10. Using your left hand, pull the blade control handle
all the way toward the upper handle.

11. Release the button.

12. Grasp the recoil rope starter handle with your right
hand and slowly pull towards you until you feel a
slight resistance, then pull firmly until your arm is
fully extended.

13. If engine does not start by second pull, repeat steps
8,910,11 and 12.

10

SecondTime StartingEngine

NOTE: Follow these instructions if the self starter is

already in the energized mode.

_, WARNING: NEVER assume starter is in

the de-energized mode, even if the key is in
the locked position and or removed from the
engine. ALWAYS de-energize starter prior to
performing any maintenance or service to the
engine and or mower. Follow instructions on
the engine and or machine to de-energize

starter.

Co°tre,

Figure 12

1. Check oil level and add fuel, ifnecessary.

2. Open shut off valve (ifequipped) 1/4 turn.

3. Turn safety key 1/4 turn clockwise to RUN position.

4. Firmly push primer bulb 3 times (For a cold engine
only!).

5. While standing at upper handle, depress the starter
control button with the thumb of your right hand.

6. Using your left hand, pull the blade control handle
all the way toward the upper handle. See Figure 12.
Starter will de-energize and engine will start.
(NOTE: If engine does not start, release blade
control handle and follow steps 8, 9, 10, 11 and 12
in the "First Time Starting Engine" instructions.)

NOTE: If any problems are encountered, refer to the

Trouble Shooting Guide for helpful information.

ToStopEngineandBlade

WARNING: The blade wilt continue to

rotate for three seconds after the blade

control lever is released.

1.

Release safety blade control handle (the start
control button will automatically return to the off/up
position), engine and blade will stop within a few

seconds.

NOTE: Engine may stop with a ratcheting sound. This

sound is the self starter being reactivated/energized for
the next start.

2. Turn safety key 1/4 turn counterclockwise to LOCK
position. Remove key and store in a safe place.

ToDe-EnergizeSelfStarter

Remove spark plug wire from spark plug.
Turn safety key to RUN position (1/4 turn

clockwise).

While standing in the operating position, depress

the starter control button fully with the thumb of your

right hand.

Using your left hand, pull the control handle all the
way toward the upper handle. (Release button and
wait until blade and starter stop rotating).

Release safety blade control handle (the start
control button will automatically return to the off/up

position).

Remove safety key.

NOTE: Engine will crank over upon actuating

equipment starting controls, but will not spark if spark
plug wire was removed from spark plug as described

above. Once engine has stopped cranking, self starter
is de-energized.

_lb WARNING: Self Starting System: If these

instructions are not followed, amputation or
severe laceration can result.

ALWAYS disconnect spark plug, de-energize
starter, lock and remove safety key BEFORE

performing ANY service to the engine or mower.

DO NOT attempt any maintenance or repairs to the
self starter.

NEVER assume starter is de-energize, even if key

is in LOCK AND REMOVE position and/or removed
from engine.

BEFORE removing grass or other debris from

under mower deck; BEFORE changing oil, air filter
or spark plug; BEFORE removing blade for
servicing; BEFORE performing any other service to
engine or mower; BEFORE transporting mower-

ALWAYS DE-ENERGIZE SELF STARTER.

UsingYourRotaryMower

,_ WARNING: Never operate your unit without

either the rear deflector or entire grass catcher
assembly in place.

Be sure that lawn is clear of stones, sticks, wire, or
other objects which could damage lawn mower or

engine. Such objects could be accidentally thrown

by the mower in any direction and cause serious

personal injury to the operator and others.

For best results, do not cut wet grass because it
tends to stick to the underside of the mower,

preventing proper discharge of grass clippings, and
could cause you to slip and fall. New grass, thick
grass or wet grass may require a narrower cut.

Blade speed should be adjusted to the condition of
the lawn.

11

For a healthy lawn, never cut more than one-third of
the length of the grass at any one cutting. Lawn
should be cut in the fall as long as there is growth.

WARNING: If you strike a foreign object,
stop the engine. Remove wire from spark

plug and de-energize starter, turn key off and
remove. Thoroughly inspect the mower for

any damage, and repair the damage before

restarting and operating the mower.

Excessive vibration of the mower during
operation is an indication of damage. The unit
should be promptly inspected and repaired.

UsingtheMulcher

For effective mulching, do not cut wet grass
because it tends to stick to the underside of the

deck, preventing proper mulching of grass
clippings. New or thick grass may require a

narrower cut. The ground speed should be

adjusted to the condition of the lawn. If mowing has

been delayed and the grass has been allowed to

grow in excess of 4", mulching is not

recommended. Mow using the grass bag to reduce

the grass height to 3-1/4" maximum before

mulching.

SECTION6: MAKINGADJUSTMENTS

WARNING: Be sure to disconnect the
spark plug wire and De-energize starter

before performing any adjustments or repairs.
DO NOT attempt any maintenance or service
to the engine and or mower equipped with the
safety key in the unlocked and or energized

mode.

WARNING: NEVER assume starter is de-

energized, even if the key is in the locked
position and or removed from the engine.
ALWAYS de-energize starter prior to
performing any maintenance or service to
the engine and or mower. Follow instructions
on the engine and or machine to de-energize

starter.

AdjustingHandleHeight

Your mower is shipped with the handle in the higher
height position .To lower the handle height for your
convenience, proceed as follows:

Lower _--_

Handle ___ / Notch

Figure 13

Remove the starter rope from the rope guide.
Remove the upper handle by removing the hand

knobs and carriage bolts. Lay the upper handle out
of the way, being careful not to bend or kink cables.
Remove the hairpin clips from the weld pins on the
handle brackets. Press outward on the legs of the

lower handle, and remove it from the mower.

Remove carriage bolts and wing nuts from the two
handle brackets on both sides.

Turn the lower handle around so the notches on the
bottom of the lower handle are facing forward as

shown inFigure 13. Reassemble, placing the

bottom holes in the handle over the weld pins in the
handle mounting bracket.
Reassemble the upper handle.
Place the hairpin clips in the inner holes in the weld
pins. Secure carriage bolts and wing nuts on the
handle brackets. Reattach the starter rope.

Carburetor

WARNING: If any adjustments are made
to the engine while the engine is running (e.g.

carburetor), keep clear of all moving parts
and heated surfaces (e.g. muffler).

Minor carburetor adjustments may be required to
compensate for differences in fuel, temperature,
altitude and load. To adjust carburetor, refer to the
engine manual.

NOTE: A dirty air cleaner will cause an engine to run
rough. Be certain air cleaner is clean and attached to
the carburetor before adjusting carburetor.

CuttingHeight

An adjusting plate and thumb lever at each wheel
position provides cutting height adjustment. Each
adjusting plate has nine height positions. Height of cut
will be changed when the thumb lever is moved from

one hole to another.

Simply depress the lever towards wheel and move
wheel and lever assembly to desired position. All
wheels must be placed in the same relative

position. See Figure 14.

12

Heig ht

dJeU:et;ent

Figure 14

SECTION7: MAINTAININGYOURLAWNMOWER

WARNING: Be sure to disconnect the

spark plug wire and De-energize starter

before performing any repairs or
maintenance. DO NOT attempt any

maintenance or service to the engine and or
mower equipped with the safety key in the

unlocked and or energized mode.

WARNING: NEVER assume starter is de-

energized, even if the key is in the locked
position and/or removed from the engine.

ALWAYS de-energize starter prior to
performing any maintenance or service to

the engine and or mower. Follow instructions
on the engine and or machine to de-energize

starter.Always observe safety rules when
performing any maintenance.

ReplacingRearFlap

To remove rear flap, cut off the flat end of the wire
rod which secures it to the deck. See Figure 15.

Attach the new flap and new rod to deck, bending
the ends of the new rod over to secure to deck.

Door

Handle
Bracket

Bracket

_Rear

Flap

Figure 15

DeckCare

NOTE: We do not recommend the use of pressure
washers or garden hose to clean your unit. These may

cause damage to electric components, spindles,

pulleys, bearings or the engine. The use of water will
shorten lifeof the mower and reduce its serviceability.

The underside of the mower deck should be
cleaned after each use to prevent a build-up of

grass clippings, leaves, dirt or other matter. If this
debris is allowed to accumulate, it will invite rust

and corrosion, and may cause an uneven
discharge of grass clippings at the next cutting.

The deck may be cleaned by tilting the mower and
scraping clean with a suitable tool (make certain the
spark plug wire is disconnected).

Engine

A list of key maintenance jobs required for good
performance by the mower is given below. Follow the
accompanying engine manual for detailed list and

instructions.

Change engine oil after the first two operating

hours and every 25 operating hours thereafter.
Always check oil level before starting engine.

Clean the engine periodically. Remove dirt and
debris with a cloth or brush. We do not recommend

the use of pressure washers or garden hose to
clean your unit.These may cause damage to

electric components, spindles, pulleys, bearings or
the engine. The use of water will shorten life of the

mower and reduce its serviceability.

Clean the spark plug and reset the gap to.030" at

least once a season or every 50 hours of operation.

Spark plug replacement is recommended at the
start of each season. Refer to the engine manual

for correct spark plug type.

Inspect muffler periodically, and replace if

necessary. Damaged mufflers or spark arresters
can create a fire hazard.

WARNING: Make sure to avoid muffler and

surrounding areas while the mower engine is
hot because temperature of these areas of the

engine may exceed 1500 F.

13

Lubrication

(Refer to Lubrication Chart in Figure 16.)

WARNING: Be sure to disconnect the
spark plug wire and De-energize starter

before performing any repairs or
maintenance. DO NOT attempt any

maintenance or service to the engine and or
mower equipped with the safety key in the

unlocked and or energized mode.

WARNING: NEVER assume starter is de-

energized, even if the key is in the locked
position and/or removed from the engine.
ALWAYS de-energize starter prior to
performing any maintenance or service to
the engine and or mower. Follow instructions
on the engine and or machine to de-energize
starter.Always observe safety rules when
performing any maintenance.

Blade Control

Lubricate the pivot points on the blade control
handle and the brake cable at least once a season

with light oil. The blade control must operate freely
in both directions.

Rear& Side Discharge Doors

The torsion springs and pivot points should be
lubricated periodically with light oil to prevent any
rust or binding. Door must work freely.

NOTE: When tipping the unit, empty the fuel tank and

keep engine spark plug side up.

Lubricate

Figure 16: Lubrication Chart

Wheels

The wheels require no lubrication. However, ifthe
wheels are removed for any reason, lubricate the

surface of the axle bolt and the inner surface of the
wheel with light oil. Engine oil may also be used.

Transmission

The transmission is pre-lubricated and sealed at
the factory and does not require lubrication on a

regular basis as part of maintenance. However, if
you disassemble the transmission for any reason,

refill with two ounces of AIvania grease (part # 737-

0168) as part of reassembly.

Engine

Follow engine manual for instruction and schedule
of lubrication.

BladeCare

Periodically inspect the blade adapter and pulley
for cracks, especially if you strike a foreign object.

Replace when necessary.

WARNING: When removing the cutting

blade for sharpening or replacement, protect
hands by using heavy gloves or a thick rag to

grasp the cutting blade.

To

To

Disconnect spark plug wire from spark plug.

RemoveBlade

Remove the bolt and bell washer which hold the

blade-pulley assembly to the engine crankshaft.

See Figure 17. Remove assembly from crankshaft.

Remove the two bolts and lock nuts from the blade
assembly.

Remove the blade from the blade adapter and

pulley.

Replace Blade:

Before reinstalling the blade-pulley assembly to the

unit, lubricate engine crankshaft and inner surface
of the blade adapter with light oil or engine oil.

Turn mower on its side making sure that the air filter
and the carburetor are up.

Lock Nut Pulley

_ Assembly

Blade _ L_ _-_- Lock Nut

Adapter .

_ Blade

Hex B°lt -_P _tr _,_€_ _

waBs_hl!r_ .Hex H21:Bolt

Figure 17

Also lubricate the bolt holes, bolt and the inner
surface of the nuts.

Install the blade adapter on the pulley with the "star"
away from the pulley. See Figure 17.

14

Place the new blade on the blade adapter with the
side marked bottom (or with part number) facing
away from the adapter.
Secure the blade to the assembly with two hex
bolts and lock nuts. Tighten the hex bolts to the
recommended torque. Refer to 'Blade Mounting
Torque' section on this page.

Install the blade assembly on the crankshaft. See
Figure 17. Secure with the hex bolt and bell washer
(cupped side of washer to blade) and tighten to the
recommended torque. Refer to 'Blade Mounting
Torque' section on this page.

IMPORTANT:The bolt, used to secure the blade to the
engine, is specially heat-treated. Do not substitute. To

order replacement bolt, refer to the parts list inthe back
of this manual.

_lb WARNING: TO ensure safe operation ofyour lawn mower, check all nuts and bolts

periodically and tighten if necessary,

To Sharpen Blade:

The blade can be sharpened with a file or on a
grinding wheel. Do not attempt to sharpen the

blade while it is still on the mower.
Follow the original angle of grind as a guide. Make
sure that each cutting edge receives an equal

amount of grinding to prevent an unbalanced blade.

NOTE: An unbalanced blade will cause excessive

vibration when rotating at high speeds, may cause

damage to the mower and could break, causing
personal injury.

The blade can be tested by balancing it on a round
shaft screwdriver. See Figure 18. Remove metal

from the heavy side until it balances evenly. It is
recommended that the blade always be removed

from the adapter for the best test of balance.

1.Insert screw driverthrough hole

d.-"

2. Blade should be parallel to ground

Screw
Driver _ Blade

I o' o I

Ground

Figure 18

Blade Mounting Torque:
Blade adapter bolts: 120 in.tbs, minimum, 150 in.lbs.

maximum.

Center bolt: 450 in.lbs, minimum, 600 in.lbs, maximum.

Replacing Drive Belt

Loosen this screw

Shoulder

Screw

Screw

Transmission

Cover

Figure 19

Remove two shoulder screws securing the front

drive cover to the mower deck. See Figure 19.

Press inward on the sides of the front drive cover
and release the tabs that secure the front drive
cover tothe height adjuster brackets. Remove drive

cover from the mower.

Using a torx wrench, loosen the screw holding the

belt tension spring to the transmission. See Figure

19. Do not remove the screw completely. As you

loosen the screw, the tension on the belt will be

released.

Push the transmission up a little and slide the belt
off the transmission pulley.

Lift the mower to access the belt from the underside
of the mower.

Slide the belt off the engine pulley and around the

blade. See Figure 20.

WARNING: As always, use a thick piece of

rag to handle the blade while sliding the belt
around it. Make sure the engine does not start
at all while doing this job.

Replace with the new belt, working around the

blade. Make sure the belt is firmly seated on the
engine pulley while pulling from the other side and
sliding it around the transmission pulley.

Put the mower down with all four wheels firmly

placed on one level.

15

Tighten the screw, loosened earlier, to secure the
belt tension spring to the transmission, and

reassemble the front drive cover.

_ blade

Hex Bolt

Figure 20

SECTION8: OFF-SEASONSTORAGE

If you are not going to use the mower for more than 30

days or more, prepare the equipment for storage.

_ WARNING: Be sure to disconnect the

spark plug wire and De-energize starter

before performing any repairs or
maintenance. DO NOT attempt any
maintenance or service to the engine and or
mower equipped with the safety key in the
unlocked and or energized mode.

WARNING: NEVER assume starter is de-

energized, even if the key is in the locked
position and or removed from the engine.
ALWAYS de-energize starter prior to
performing any maintenance or service to
the engine and or mower. Follow instructions
on the engine and or machine to de-energize

starter.

Clean and lubricate mower thoroughly as described

in the lubrication instructions.

Refer to accompanying engine manual for engine
storage instructions.

Coat mower's cutting blade with chassis grease to

prevent rusting.

Store mower in a dry, clean area. Do not store next
to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust-proof the equipment. Using a light oil or
silicone, coat the equipment, especially cables and all
moving parts.

16

SECTION9: TROUBLESHOOTINGGUIDE

Corrective ActionsTrouble

Engine fails to

start

Possible Cause(s)

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

1.

2.

3.

1.

2.

3.

Blade control handle disengaged.
Start control button not depressed.

Spark plug wire disconnected.
Safety key not in run position.
Dirty air cleaner.
Primer button not depressed.
Fuel tank empty or stale fuel

Blocked fuel line.
Faulty spark plug.

1. Engage blade controlhandle.

2. Depress starter control button.

3. Connect wire to spark plug.

4. Safety key not in run position.

5. Refer to the engine manual.

6. Refer to the engine manual.

7. Clean fuel line.

8. Clean, adjust gap or replace.

9. Refer to the engine manual.
Engine flooded. 10. Wait for a while and crank the engine.
Self starter already de*energized. 11. Use recoil starter to start engine..

Engine runs Spark plug wire loose. 1. Connect and tighten spark plug wire. Check for fouling.

erratic Blocked fuel line or stale fuel 2. Clean fuel line; fill tank with dean, fresh gasoline.

Carburetor out of adjustment. 3. Refer to the engine manual.

Engine Engine oil level low. 1. Fill crankcase with proper oil

overheats Dirty aircleaner. 2. Refer to the engine manual.

Air flow restricted. 3. Stop engine and disconnect spark plug wire. Remove

blower housing and clean.

4. Carburetor not adjusted properly 4. Refer to the engine manual.
Occasional skip 1. Sparkplug gap too close. 1. Adjust gapto.030".
at high speed 2. Carburetor adjustment improperly set. 2. Refer to the engine manual.

Idles poorly 1. Spark plug fouled, faulty or gap too wide. 1. Reset gap to.g30" or replace spark plug.

2. Carburetor not adjusted. 2. Refer to the engine manual.

Excessive 1. Cutting bladeloose or unbalanced. 1. Tighten blade and adapter. Balance blade.

vibration 2. Bent cutting blade. 2. See an authorized service dealer.

Mower will not 1. Wet grass. 1. Wait until later to cut.
mulch grass 2. Excessively high grass. 2. Mow once at a high cutting height, then mow again at

desired height.

Uneven cut 1. Wheels positioned incorrectly. 1. Place all four wheels in same height position.

2. Dullblade. 2. Sharpen or replace blade.

NOTE: For repairs beyond the minor adjustments above, contact your local Service dealer.

17

SECTIONI0: ILLUSTRATEDPARTSLISTFORMODEL560SERIES

100

73

72

96

74

4O

99

\

97

7O

68

79

48

78

\

43

8

14

87

76

20

17

ModelSeries560

Ref.

Pa_ No.

No.

1, 710-1174
2, 710-1205
3, 720-0279
4, 736-0451
5, 720-0284
6, 714-0104
7, 738-0481A
8, 736-0456
9, 736-0182

10. 736-0105

11. 710-0599

12. 736-0270

13. 682-7000

14. 782-5004

15. 782-5007A

16. 742-0741
742-0641

17. 714-0101

18. 736-3013

19. 736-0865

20. 717-1762
717-1761

21. 715-0221

22. 782-7551

23. 716-0102

24. 736-0474

25. 732-0706
732-0707

26. 720-0426

27. 710-0216

28. 682-0509

29. 782-0511A
782-0512B

30. 736-0447

31. 748-0355

32. 782-5002

33. 712-0798

34. 736-0331

35. 710-1257

36. 736-0452

t Not shown

Description

Carriage Bolt
Rope Guide

Wing Nut

Saddle Washer
Handle Knob

Hairpin Clip
Shoulder Screw

Flat Washer ,510 I,D, x 1,373 O,D,
Spring Wash, ,500 I,D, x 1,00 O,D,

Bell Washer ,375 I,D, x ,870 O,D,

Tapp Screw 1/4-20 x ,500

Bell Wash, ,265 I,D, x ,75 O,D,
Mulching Plug (Hinged)

Rear Baffle RH
Mulching Plug

Mulching Blade w/Star

Ref.

PaN No.

No.

37. 710-0606

38. 748-0411

39. 756-1146A

40. 712-0324

41. 782-0082A

42. 710-1650

43. 731-1936A

44. 710-1008

45. 631-0075B

46. 711-1293

47. 712-0271

48. 782-7599A

49. 710-0216

50. 712-0431

51. 710-0896

52. 750-0434

Description

Hex Screw 1/4-20 x 1,5"
Blade Adapter

Drive Pulley
Hex Lock Nut

Rear Dischage Deck 21"
Shld, Screw

Transmission Cover
TT Screw

Engine Spacer Assembly
Belt Keeper Pin

Hex Nut 1/4-20
Grassbag Door

Hex Hd, Cap Scr, 3/8-16
Flange L-Nut 3/8-16
AB Tap Screw 1/4-14 x ,625"
Spacer

Standard Blade
Hairpin Clip

Flat Washer
Snap Ring

Gear 14T RH
Gear 14T LHt

Dowel Pin

Wheel Dust Cap

Snap Ring

Washer DD 1,5" O,D,

Front Lever RH
Front Lever LHt

Knob
Hex Screw

Pivot Plate Assembly
Height Adj, Plate LHt
Height Adj, Plate RH

Wave Washer

Bearing Support
Front Baffle

Hex Nut
Bell Washer
Hex Bolt
Bell Washer

53. 710-0286

54. 747-O996

55. 732-O8O9

56. 720-0312

57. 738-0507B

58. 732-0866

59. 17489A
17488A

60. 682-3058

682-3059

61. 782-5003

62. 710-1017

63. 682-3056A

64. 682-3057A

65. 682-0512A

66. 682-0511A

67. 747-0995A

68. 664-0123

69. 710-0501

70. 710-0431

71. 647-0070
731-2623

72. 732-1171

73. 720-0428

Pan Hd, Screw 1/4-20 x ,5"
Pivot Rod
Torsion Spring

Foam Grip
Shoulder Screw

Spring Lever
Pivot Bar LHt

Pivot Bar RH
Handle Bracket Assembly RH

Handle Bracket Assembly LHt
Rear Baffle LHt

Scr, AB 1/4-14 x 0,625"
Handle Brkt, Ass'y Comp, RH

Handlr Brkt, Ass'y Comp, LH
Height Adjuster Ass'y Comp, RH

Height Adjuster Ass'y Comp, LH
Grassbag Frame
Grass Bag w/Half Sail
Hex Hd, Cap Screw

Saddle Washer
Control Handle

Bail Cover t
Compression Spring

Button

19

ModelSeries560

Ref.
No.

74.

75.

76.

77.

78.

79.

80.

81.

82.

83.

84.

85.

86.

87.

89.

90.

91.

Part No. Description

749-1405A
746-1141
731-0981A
734-2042
734-2050
710-0703
712-0397
731-1236
732-0700
754-0465
749-0907B
746-0960
731-1409
618-0657
747-0710
782-7006
732-0731

Upper Handle
Control Cable

Hub Cap
Wheel 8 x 2

Wheel 14 x 2
Carriage Bolt

Wing Nut
Trail Shield

Wire
V-Belt
Lower Handle
Drive Cable
Chute Deflector

Transmission Assembly Comp.
Hinge Pin
Hinge Mtg, Brkt.
Torsion Spring

Ref.
No.

92.

93.

94.

95.

96.

97.

98.

99.

100.

101.

102.

103.

104.

105.

106.

Part No. Description

732-0708
741-0604A
715-0168
716-0209
732-1172

731-2532
782-0156

731-2533
747-2136
710-1256
750-1166

750-1166
726-0240
732-1043
715-0169
756-1231
737-0476

Bearing Retainer
Bearing Sleeve .50 i.D.

Pin
Retention Spring

Torsion Spring
Control Cover LH

Lever
Control Cover RH
Lower Bail Handle
Hi-Low Screw

Sleeve Spacer LH
Sleeve Spacer RH

Cable Tie
Belt Tension Spring

Roll Pin
input Pulley

Bottle of Oil

2O

21

22

23

MANUFACTURER'S LIMITED WARRANTY FOR:

I I I W _lllmlF IIMIImllMIImlr I

The limited warranty set forth below is given by Troy-Bilt LLC
with respect to new merchandise purchased and used in the

United States, its possessions and territories.

Troy-Bilt LLC warrants this product against defects for a
period of two (2) years commencing on the date of original
purchase and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or
workmanship. This limited warranty shall only apply if this
product has been operated and maintained in accordance
with the Operator's Manual furnished with the product, and
has not been subject to misuse, abuse, commercial use,
neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril
or natural disaster. Damage resulting from the installation or
use of any accessory or attachment not approved by Troy-Bilt

LLC for use with the product(s) covered by this manual will

void your warranty as to any resulting damage.

Normal wear parts or components thereof are subject to
separate terms as follows: All normal wear parts or
component failures will be covered on the product for a period
of 90 days regardless of cause. After 90 days, but within the
two year period, normal wear part failures will be covered
ONLY IF caused by defects in materials or workmanship of
OTHER component parts. Normal wear parts and
components include, but are not limited to: batteries, belts,
blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber,

and tires.

HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-866-840-6483 or 1-
330-558-7220, or log on to our Web site at www.troybilt.cem.

This limited warranty does not provide coverage in the
following cases:

a. The engine or component parts thereof. These items

carry a separate manufacturer's warranty. Refer to
applicable manufacturer's warranty for terms and

conditions.

b. Log splitter pumps, valves, and cylinders have a sepa

rate one year warranty.

c. Routine maintenance items such as lubricants, filters,

blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal

deterioration of the exterior finish due to use or
exposure.

d. Troy-Bilt LLC does not extend any warranty for

products sold or exported outside of the United States,
its possessions and territories, except those sold
through Troy-Bilt LLC's authorized channels of export

distribution.

e. Parts that are not genuine Troy-Bilt parts are not

covered by this warranty.

f. Service completed by someone other than an

authorized service dealer is not covered by this
warranty.

g. Transportation charges and service calls are not

covered.

No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,

applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind Troy-Bilt LLC. During the period of the
warranty, the exclusive remedy is repair or replacement

of the product as set forth above.
The provisions as set forth in this warranty provide the

sole and exclusive remedy arising from the sale. Troy-Bilt
LLC shall not be liable for incidental or consequential

loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services
or for rental expenses to temporarily replace a warranted
product.

Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how

long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.

In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration

of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

Tr0y-Bilt LLC, P.O.BOX361131CLEVELAND,0HI0 44136-0019; Phone:[phone]