How it Works
Troy-Bilt
Loading...
1028
User Manual
32 pgs10.61 Mb0
Table of contents
Loading...

Troy-Bilt 1028, 1130 User Manual

Operator’s Manual
SNOW THROWER
Storm Tracker
MODELS
1028
1130
Model 1028 Shown
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered,
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO
PRINTED IN U.S.A.
769-00395B.fm
.
(6/04)
TABLE OF CONTENTS
Content Page
Important Safe Operation Practices 3 Assembling Your Snow Thrower 5 Know Your Snow Thrower 6 Operating Your Snow Thrower 8 Making Adjustments 11
Content Page
Servicing Your Snow Thrower 14 Trouble Shooting 17 Illustrated Parts 18 Commercial Warranty 31 Residential Warranty 32
Maintaining Your Snow Thrower 12
FINDING MODEL NUMBER
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. A sample model plate is also given below. You can locate the model plate by standing at the operating position and looking down at the rear of the snow thrower. This information will be necessary to use the manufacturer’s web site and/or help from the Customer Support Department or an authorized service dealer.
Copy the model number here:
Copy the serial number here:
www.troybilt.com
TROY-BILT LLC P. O. BOX
361131 CLEVELAND, OH 44136 330-558-7220 1-800-520-5520
CUSTOMER SUPPORT
Please do NOT return the unit to the retailer from where it was purchased, without first contacting Customer Support.
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, you can seek help from the experts. Choose from the options below:
Visit troybilt.com for many useful suggestions. Click on Customer Support button and you will get the four options reproduced here. Click on the appropriate button and help is immediately available.
The answer you are looking for could be just a mouse click away!
If you prefer to reach a Customer Support Representative, please call 1-800-520-5520.
The answer you are looking for could be just a mouse click away!
Engine
Manual
The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with your unit, for more information.
2

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

This sym bol points out im portant safety instructions, which if not follow ed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this m anual before attem pting to operate injury. W hen you see this sym bol— heed its warning.
this machine. Failure to com ply with these instructions may result in personal
WARNING:
Engine E xhaust, som e of its constituents, and certain vehicle com ponents contain or em it chem icals know n to the State of California to cause cancer, birth defects or other reproductive harm
.
DANGER: This machine was built to be operated according to the rules for safe operation in this
m anual. As with any type of pow er equipm ent, carelessness or error on the part of the operator can result in serious injury. This machine is
capable of am putating hands and feet and throw ing objects.
Failure to observe the follow ing safety instructions could result in serious injury or death.

TRAINING

1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.
2. Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.
4. Never allow adults to operate this machine without proper instruction.
5. Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially when operating in reverse.

PREPARATION

1. Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.
3. Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.
4. Use a grounded three-wire extension cord and receptacle for all units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed rock surfaces.
6. Disengage all controls before starting the engine.
7. Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.
8. Let engine and machine adjust to outdoor temperature before starting to clear snow.
9. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.
a. Use only an approved gasoline container. b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition. c. Never fuel machine indoors. d. Never remove gas cap or add fuel while the
engine is hot or running. e. Allow engine to cool at least two minutes before
refueling. f. Never over fill fuel tank. Fill tank to no more than
½ inch below bottom of filler neck to provide space
for fuel expansion. g. Replace gasoline cap and tighten securely. h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine. i. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.). j. Allow machine to cool at least 5 minutes before
storing.

OPERATION

1. Do not put hands or feet near rotating parts, in the auger/ impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet.
2. The auger/impeller control is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury.
3. The controls must operate easily in both directions and automatically return to the disengaged position when released.
4. Never operate with a missing or damaged chute assembly. Keep all safety devices in place and working.
3
5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.
6. Do not operate machine while under the influence of alcohol or drugs.
7. Muffler and engine become hot and can cause a burn. Do not touch.
8. Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards windows, walls, cars etc. Thus, avoiding possible property damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear snow at too fast of a rate.
13. Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting or not in use.
15. Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when in reverse.
16. If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.
17. Disengage all controls and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the chute assembly, making any adjustments, or inspections.
18. Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine is running.Shut off engine and remain behind handles until all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or telephone 1- 800 520-5520 of your nearest servicing dealer.
for assistance and the name

MAINTENANCE AND STORAGE

1. Never tamper with safety devices. Check their proper operation regularly. Refer to the maintenance and adjustment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage all controls and stop engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting.
3. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed the engine. The governor controls the maximum safe operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer’s (OEM) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”
6. Check clutch controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as necessary.
8. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper instructions on off-season storage.
WARNING: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.
4

SECTION 2: ASSEMBLING YOUR SNOW THROWER

Unpacking
• Remove screws from the top sides and ends of the shipping crate.
• Set panel aside to avoid tire punctures or personal injury.
• Remove and discard plastic bag that covers unit.
• Remove any loose parts included with unit (i.e., Operator’s Manual, etc.).
• Roll unit out of crate.

Loose Parts

The augers are secured to the auger shaft with two shear pins and cotter pins. If you hit a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Two replacement shear pins and cotter pins are provided for your convenience. Store in a safe place until needed. See Figure 1.
end of each cable) is attached to its actuator bracket.
• Secure the upper handle and lower handle with the two plastic wing nuts, cupped washers and carriage bolts previously removed. Attach these hardware on the lower hole in the handles. See Figure 2.
• Tighten the two wing nuts already in place on the upper holes and secure the handles firmly. Slide the shift rod connector down over the end of the lower shift rod. Tap the connector until it locks over the lower shift rod. See Figure 2.
NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction of movement.
Carriage
Bolt
Shear Pins
Cotter Pins
Figure 1
IMPORTANT:
standard hex pins. Any damage to the auger gearbox or other components from using standard pins will not be covered by your snow thrower’s warranty.
NEVER replace the auger shear pins with

Items Required For Assembly

1. Pair of pliers
2. Engine oil
3. Fresh gasoline

Before Assembly

• Disconnect spark plug wire and ground it against the engine to prevent unintended starting.
NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

Assembling Handle

For shipping purposes, the upper handle is secured loosely to the lower handle with four wing nuts.
• Remove the lower plastic wing nut, cupped washer and carriage bolt from each side of the lower handle. See Figure 2.
• Raise the upper handle assembly until it locks over the lower handle.
• Look at the lower rear of the snow thrower frame to be sure all the cables are aligned with the cable roller guides. Make sure the spring (found at the
Cupped Washer
Wing
Nut
Hairpin Clip
Carriage Bolt
Lower Chute Rod
Figure 2
Upper Chute Rod

Attaching Chute Directional Control

Model 1028
• Remove the hairpin clip from the upper chute rod and slide the upper chute rod through the upper chute rod bracket and into the lower chute rod. A pair of pliers may help in this job.
• Align the two holes on both chute rods and insert the hairpin clip removed earlier, through these holes. See Figure 2.
Model 1130
• Adjust the eyebolt on the chute directional control so the rod does not come into contact with the engine by moving the hex nut against the handle (if necessary). Retighten the wing nut to secure the directional control in this position.
5
• If not already attached, slip the cables that run from the handle panel to the chute assembly into the cable guide located on top of the engine. See Figure 3.
• Plug the wire from the headlight into the alternator lead coming from the right side of the engine underneath the fuel tank.
Cable
Discharge Chute
Cable Guide
Lamp Wire
Figure 3
• If not already attached, unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind the headlight wire around the lower right handle until excess slack is removed. See Figure 4.

Clean-Out Tool

• This tool, along with the electric cord, is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove the electric cord before operating the snow thrower.

SECTION 3: KNOW YOUR SNOW THROWER

Drive Control / Auger Control Lock

Heated Handles Switch†
Shift Lever
Chute Tilt Control
Alternator Lead
NOTE:
Wheels are omitted from illustration for clarity.
Figure 4
Heated Grip†
Alternator Lead
Chute Assembly
Clean-Out Too l
Auger
Headlight††
Chute Directional Control
Skid Shoe
Figure 5
WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.
Auger Drive Control
Track Steering Control
Primer
Choke
Safety Ignition Key
Throttle
† Model 1028
†† Model 1130 equipped with one (1)
Control
Electric Starter Button
Switch Box
Recoil Starter Handle
Closed
Open
Fuel Shut-Off Valve
*If Equipped
Drive Control / Auger Control Lock
The drive control is located on the right handle. Squeeze the drive control to engage the wheel drive. Release to stop. See Figure 5.
6
The drive control also locks the auger control so you can turn the chute directional control without interrupting the snow throwing process. If the auger control is engaged along with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release both controls to stop the augers and track drive.
IMPORTANT:
changing speeds.
Always release drive control before

Auger Drive Control

The auger drive control is located on the left handle. Squeeze the control grip to engage the augers. Release to stop the snow throwing action. (Drive control must also be released.) See Figure 5.
IMPORTANT:
operating your snow thrower. Read and follow all instructions carefully and perform all adjustments to verify your snow thrower is operating safely and properly.
Refer to Auger Control Test on page 9 prior to

Chute Tilt Control

The distance snow is thrown can be changed by adjusting the angle of the upper chute. Move the chute tilt control forward to decrease the distance, and backwards to increase distance. See Figure 5.

Skid Shoe

The space between the shave plate and the ground can be adjusted by positioning the skid shoes. Refer to Skid
Shoe Adjustment on page 12.

Shift Lever

The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. See Figure 5.
Forward
Your snow thrower has six forward (F) speeds, with position number one (1) being the slowest speed.
Reverse
Your snow thrower has two reverse (R) speeds, with position number one (1) being the slowest speed.
IMPORTANT:
changing speeds.
Always release drive control before
• Counterclockwise to discharge to the right.

Clean-Out Tool

The clean-out tool is designed to clear a clogged chute. Refer to page 10 for instructions on how to properly use it.
WARNING: Never use your hand to clear a clogged chute. Shut off engine and remain behind handles until all moving parts have stopped before unclogging. Use the clean-out tool or a stick to unclog.

Heated Handles Switch (Model 1028)

This switch is located on the right side of the snow thrower dash panel. To activate the heated handles, toggle the switch to the right to generate heat within the handle grips. Toggle the switch to the left to the OFF position after using the snow thrower. See Figure 5.
NOTE: The heated handles grips are a compliment to, not a substitute for, proper cold weather outerwear for the operator’s hands. It is recommended that the snow thrower operator wear gloves/mittens to avoid extremities of winter while operating this equipment.

Track Steering Controls

The left and right track steering controls are located on the underside of the handles and they are used to assist in steering the snow thrower. Squeeze the right track control when turning right, squeeze the left control when turning left. Operate your snow thrower in open areas until you become familiar with these controls. See Figure 5.
NOTE: It is easier to maneuver a non-running snow thrower with both track steering controls held in simultaneously.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely. See Figure 5.

Fuel Shut-Off Valve (Optional Equipment)

On models so equipped, the fuel shut-off valve, located under fuel tank, controls fuel-flow from the fuel tank to the engine. See Figure 5.

Chute Directional Control

The chute directional control is located on left side of the snow thrower. See Figure 5.
To change the direction in which snow is thrown, turn chute directional control as follows:
• Clockwise to discharge to the left.

Safety Ignition Key

The safety ignition key must be fully inserted and snapped in place before the unit will start. Remove the ignition key to prevent unauthorized use of equipment. See Figure 5.
IMPORTANT:
7
Do NOT attempt to turn the key.

Headlight

The headlight is on whenever the engine is running.

Track Lock Lever

The track lock lever is located on the right side of the snow thrower and is used to select the position of the auger housing and the method of track operation. Move the lever to the right, then forward or backward to one of the three positions. See Figure 6.
Transport: Raises the front end of the snow thrower for
easy transport. Using proper caution, this position may also be used on many gravel driveways to clear snow while leaving gravel undisturbed.
Normal Snow: Allows the tracks to be suspended
independently for continuous ground contact.
Packed Snow: Locks the front end of the snow thrower
down to the ground for hard-packed or icy snow conditions.
Packed Snow

SECTION 4: OPERATING YOUR SNOW THROWER

Normal Snow
Track Lock Lever
Transport
Figure 6

Before Starting

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas And Oil Fill-up

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.
WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.
•A plastic cup is provided inside the fuel fill opening to protect the tank during manufacturing. Remove and discard. Use the threaded fuel tank cap to close after fill-up.

To Start Engine

• Attach spark plug wire to spark plug. Make certain the metal loop on end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.
• Make certain the fuel shut-off valve, if so equipped, is in the OPEN (vertical) position.
• Make certain the auger and drive controls are in the disengaged (up) position.
• Move throttle control up to FAST position. Insert ignition key into slot and snap in place. See Figure
5. Be certain it snaps into place. Do not turn key.
NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover.
Electric Starter
• Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.
• If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.
WARNING: The electric starter is equipped with a grounded three-wire power cord and plug and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.
• If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter.
• If you have a grounded three-prong receptacle, proceed as follows:
• Connect power cord to switch box on engine. Plug the other end of power cord into a three-prong, 120­volt, grounded, AC receptacle.
8
• Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.
• Push primer button two or three times for cold engine start, making sure to cover vent hole in primer button when pushing. DO NOT use primer to restart a warm engine after a short shutdown.
• Push starter button to start engine.
• When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF.
• When disconnecting the power cord, always unplug from the three-prong receptacle first and then from the snow thrower.
Recoil Starter
• Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.
• Push primer button three or four times for cold engine start. DO NOT use primer to restart a warm engine after a short shutdown.
NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15°F.
Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.
• To stop engine, move throttle control to “stop” or “off” position.
• Remove ignition key (DO NOT turn key) to prevent unauthorized use of equipment.
NOTE: Do not lose ignition key. Keep it in a safe place. Engine will not start without ignition key.
• Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engag e Track Drive

• With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.
• Squeeze the auger control and the augers will turn. Release it and the augers will stop.
• Squeeze drive control and the snow thrower will move. Release it and drive motion will stop.
IMPORTANT:
the drive control. Doing so will cause premature wear on the drive system’s friction wheel.
NEVER move shift lever without releasing
• Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.
• Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.
• Repeat the previous steps until engine starts.
• As engine warms up, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position

To Stop Engine

• Run engine for a few minutes before stopping to help dry off any moisture on the engine.
• To help prevent possible freeze-up of starter, proceed as follows:
Electric Starter:
• Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.
Recoil Starter
• With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times.

To Engage Augers

• To engage the augers and start throwing snow, squeeze the auger control against the left handle.
• To disengage power to the augers, release both the auger control and the drive control, if engaged.
The auger control can be locked so you can turn the chute directional control without interrupting the snow throwing process.
Auger Control Test
IMPORTANT:
operating your snow thrower for the first time and at the start of each winter season.
Check the adjustment of the auger control as follows:
• When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.
• In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting Engine. Make sure the throttle is set in the FAST position.
• While standing in the operator’s position (behind the snow thrower), engage the auger.
• Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.
• With the engine running in the FAST position and the auger control in the disengaged “up” position, walk to the front of the machine.
Perform the following test before
9
• Confirm that the auger has completely stopped rotating and shows NO signs of motion.
IMPORTANT:
immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.
• To readjust the control cable, loosen the hex jam nut on the auger control cable “Z” fitting.
• Rotate the coupling end of the cable counterclockwise to provide more slack.
• Retighten the hex jam nut. See Figure 7.
• Repeat Auger Control Test to verify proper adjustment has been achieved.
Auger Control
Z-End
If the auger shows ANY signs of rotating,
few seconds to clear any remaining snow and ice from the chute assembly.

Drift Cutters (If Equipped)

Drift cutters should be used when operating the snow thrower in heavy drift conditions.
On models so equipped, drift cutters are assembled to the auger housing inverted. Remove the carriage bolts by unthreading the hex nuts which secure them, and reinstall the drift cutters in their proper position before operating the snow thrower. See Figure 8.
If your unit is not equipped with drift cutters, contact Customer Support as instructed on page 2 for information regarding price and availability.
Snow Thrower Model Drift Cutter Kit
All models OEM-390-679
Jam Nut
Auger Control Cable
Figure 7

Clean-Out Tool

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice lodge itself in the chute assembly during operation, proceed as follows to safely clean the chute and chute opening:
• Release both the Auger Control and the Auger Control Lock.
• Stop the engine by moving the throttle to the stop position.
• Remove the clean-out tool from the mounting clip.
• Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly.
WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing. Use the clean-out tool or a stick to unclog.
• Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine.
• While standing in the operator’s position (behind the snow thrower), engage the auger control for a
Drive/
Drift
Cutter
Carriage Screws & Hex Nuts
Figure 8

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.
WARNING: The temperature of the muffler and the surrounding areas may exceed
°
150
F. Avoid these areas.
• For the most efficient snow removal, remove snow immediately after it falls.
• Discharge the snow downwind whenever possible.
• Slightly overlap each previous path.
• Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.
• Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up.
• Clean the snow thrower thoroughly after each use.
10
Loading...
+ 22 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use