For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 1 of 25
Bolo Tine Assemblies
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 2 of 25
Bolo Tine Assemblies
Ref # Part Number Qty DescriptionS/P/F
1 GW-2415 TINE HOLDER- welded steel. For left or right
2 S/F
side of tiller.
2 GW-9669 BOLT - hex hd., 1/2"-20 x 4-3/4" long. Mounts
3 GW-9914 LOCKWASHER-1/2", holder mounting2 S
4 GW-9952 WASHER - flat. Outer dia. 1.500", inner dia.
5 GW-1205 TINE HOLDER - cast iron. For left or right
6 GW-1463 BOLT - hex hd.,1/2"-20 x 5-3/4" long. Mounts
7 GW-1461 WASHER - flat. Outer dia. 1-3/4", inner dia.
8 GW-1735 BOLT 8 WASHER SET - Includes one each
9 GW-9301 KEY - tine shaft 3/16" square x 1" long2 S
10 GW-1270-1A BOLO TINE - single, Left Hand. Used on left
2
Part #2415 welded steel tine holder on tine
shaft
2
.516",thickness .182". Use with Part 119669
bolt only
2 F
side of tiller.
2
Part #1205 cast iron tine holder on tine shaft
2
17/32". Use with Part #1463 bolt only
1
Part #1483 bolt, #9914 lockwasher and #1461
washer. Use with Part 81205 tine holder only
8 S
and right side tine assemblies. Tine is
stamped either "F1" or "AL"
11 GW-1270-2A BOLO TINE- single, Right Hand. Used on left
12 GW-9711 BOLT - hex hd., 3/8"-16 x 1", tine mounting16 S
13 GW-9913 LOCKWASHER-3/8" tine mounting16 S
14 GW-9802 NUT- hex, 3/8"-16, tine mounting16 S
15 GW-2253 TINE SHIM - used as needed to correct
16 GW-2254 TINE SHIM - used as needed to correct
GW-1245K TINE REPLACEMENT KIT- unassembled.1 S/F
GW-10355 WELDED STEEL TINE HOLDER
8 S
and right side tine assemblies. Tine is
stamped either "ER" or "AR"
1
loose-fitting tines mounted on cast iron tine
holders only
1
loose-fitting tines mounted on cast iron tine
holders only
1 F
REPLACEMENT KIT - Includes one each of
Part #2415 welded steel tine holder, #9669
bolt, #9914 lockwasher and #9952 washer.
Order two kits if replacing both holders.
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 3 of 25
Depth Regulator & Tine Hood Assemblies
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 4 of 25
Depth Regulator & Tine Hood Assemblies
Ref # Part Number Qty DescriptionS/P/F
1 GW-9712 BOLT- hex. hd., 3/8"-16 x 1-1/4", drag bar
2 GW-1113-1 BUSHING - 19/64" (.300") long, drag bar2 S
3 GW-9913 LOCKWASHER - spring lock 3/8"2 S
4 GW-9802 NUT - hex., 3/8"-162 S
5 GW-1117A BAR - depth regulator Includes #9119 knob
6 GW-9120 RING - retaining (tolerance ring)1 /P
7 GW-9119 KNOB- depth regulator1 /P
8 GW-2121 BAR - drag, depth regulator1 S
9 GW-9552 SCREW - thread forming, 1/4"-20 x 1/2",
2 S
mounting
1 S
(Ref. 07) and M20 retaining ring (Ref. M6)
4 S
(lockwasher and nut not required). Mounts
hood to bracket; Replaces 9723
10 GW-9703 BOLT - hex. hd., 5/16"-18 x 3/4" hood to tiller
11 GW-9912 LOCKWASHER - spring lock, 5/16"4 S
12 GW-9929 WASHER - flat, 5/16"2 /P
13 GW-2470 HOOD tine cover with hinged flap Includes
14 GW-2413 DECAL - hood, operating Instructions1 S
15 GW-1238 DECAL- model name (HORSE)1 S
16 GW-2527 BRACKET- tine hood and depth regulator
17 GW-9308 PIN - roll (spirol), 1/4" x 1" long1 S
18 GW-9438 SPACER1 S
19 GW-9384 SPRING1 S
20 GW-9734 BOLT - hexhd., 1/4"-20 x 1"1 S
21 GW-9811 LOCKNUT - 1/4"-201 S
4 S
housing and hood bracket to rear bearing cap
1 /P
hood decals (Ref. #14 and 15)
1 /P
Replaces 2255
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 5 of 25
Electric Start System - 6HP, 7HP, & 8HP Tillers
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 6 of 25
Electric Start System - 6HP, 7HP, & 8HP Tillers
Ref # Part Number Qty DescriptionS/P/F
1 GW-9295 CABLE-battery, positive and negative
2 GW-9255 RUBBER BOOT- terminal insulating2
3 GW-9552 SCREW -self threading, 1/4"-20 x 1/2", one
2 S
terminals
3 S
for grounding negative cable and two for
mounting solenoid to bracket
4 GW-9703 BOLT- hex. hd., 5/16"-18 x 3/4", battery
5 GW-9801 NUT -hex., 5/16"-18, battery terminals2 S
6 GW-2241 BATTERY HOLD-DOWN CLAMP- with
7 GW-20418 DECAL - key switch instructions1 S
8 GW-9230 KEY SWITCH - includes two 89243 keys,
9 GW-9243 KEY -ignition, one pair1 S
10 GW-9565 BOLT - carriage, 1/4"-20 x 1-1/2", hold-down
11 GW-9910 LOCKWASHER - spring lock 1/4"2 S
12 GW-9800 NUT - hex., 1/4"-202 S
13 GW-9092B BATTERY - 12 volt, 30 amperes, side-vented.
2 S
terminals
1 S
attached Key Switch Plate (includes #20418
decal). Introduced on Tiller Serial #648406.
Use with #2182 battery bracket; Replaces
1468
1
one lockwasher and one mounting nut
(hardware not available separately from
Garden Way)
2
clamp to bracket
1 S
Comes with Part #9009 vent tube.
IMPORTANT: For Tiller Serial Nos. 685484 &
Below, contact Technical Service 9123,
Department regarding special battery
replacement kit before ordering battery;
Replaces 94878
14 GW-1959 SOLENOID - starter, includes all washers
15 GW-9912 LOCKWASHER-springlock, 5/16", solenoid
16 GW-9826 NUT - hex., 5/16"-24, solenoid left and right
17 GW-9921 LOCKWASHER-external tooth, #10, solenoid
18 GW-9809 NUT - hex., 10-32, center post on solenoid1 S
19 GW-9223 CABLE - solenoid to starter motor1
20 GW-2182 BATTERY BRACKET- introduced on Tiller
21 GW-9558 BOLT - hex. hd., 3/8"-16 x 1-1/2", bracket to
1 /P
and nuts (Ref. No's. 15, 16, 17 & 18) for
cables and wires; Replaces 9127
2 S
left and right posts
2 S
posts
1 S
center post
1
Serial #648406. Use with 52241 clamp;
Replaces 1169
2
transmission cover Replaces 9713
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 7 of 25
Electric Start System - 6HP, 7HP, & 8HP Tillers
Ref # Part Number Qty DescriptionS/P/F
22 GW-9913 LOCKWASHER - springlock, 3/8"2 S
23 GW-9265 TIE- twist, red plastic, wire retaining1 /P
24 GW-9009 VENT TUBE - 5/16" dia.1 /P
25 GW-1475 SHIELD - vent tube, 1/2" dia.1
26 GW-9224 CLAMP- vent tube shield1
27 GW-9202 TIE -red plastic1 S
28 GW-1552 WIRE HARNESS - for Tecumseh and Kohler
1
engines; Includes two receptacles; three red
wires (solenoid activate, battery recharge,
and starter switch); one green (shutoff) wire;
plastic harness tube
29 GW-9218 CLIP-metal, supports recharging wire on
30 FUSE - 6 Amperes, 3 AGC, for Tecumseh
31 DIODE - battery recharging for Tecumseh
32 GW-9910 LOCKWASHER-springlock, 1/4", for
33 GW-9800 NUT - hex., 1/4"-20 For all engines1 S
34 GW-20424 WIRE HARNESS - for Briggs and Stratton
35 GW-1554 WIRE-recharge (red), for Briggs & Stratton
1 /P
Tecumseh engine
1
engine (earlier models only). Available locally
or from Garden Way (Tecumseh x 29561)
1
engine. For authorized service dealer
replacement (Tecumseh #610935)
1 S
Tecumseh and Kohler engines
1
engine. Complete assembly only.; Includes
key switch receptacle with two red wires (with
eyelets), one green wire, plastic harness tube.
Order red recharging wire (Ref. No. 35)
separately, if needed
1 S
engine. Includes terminal and eyelet
36 GW-9266 TIE - plastic, reusableA/R S
37 LOCKWASHER - internal tooth, 1/4" Comes
1
with engine-not avail. from Garden Way
www.mymowerparts.com
For Discount Troy Bilt Parts Call 606-678-9623 or 606-561-4983
10056 Horse III (S/N 640000-855638) Page 8 of 25
Forward/Neutral/Reverse Lever & Yoke Assembly
www.mymowerparts.com