Troybilt 020245 Owner’s Manual

0

®

d

Pressure Washer / Lavadora de Presi6n

Modem / Modemo 020245

Before using this product_ read this manuaH and follow aHH Antes de utiHizar eHproducto_ Heaeste manuaH7 siga todas Has

Safety P,uHesand Operating Instructions. P,egHasde Seguridad e Instrucdones de Uso.

Questions_ Pregun_.as_ Helpiine - 1-888=611-6708 H=F 8=5 CT

Troy=BilleD is a registered trademark ofTroy=BiHt, LLC and is used under Hicenseto Bri_s & Stratton Power Products.

Troy=BiHt® es una marca registrada de Troy=BiHt,LLC 7 se usa abaio Hicencia a Bri&_s & Stratton Power Products.

BRJGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WiSCONSiN, U.S.A.

Printed in USA HanuaHNo. H96222GS Revision 2_(03/02_/2_005)

7

Safety Rules

SAVE THESE [NSTRUCTmONS

TABLE OF CONTENTS

Section H o Safety RuHes .......................... 2-4

Section 2 - Features and ControHs ................... 5

Section 3 oAssembHy ............................ 6-7

Section 4 o Operation .......................... O°H3

Section 5 ° Product Specifications ................... H4

Section 5 o Maintenance ........................ H4oH6

Section 6 o Storage .............................. H7

Section 7 oTroubleshooting ........................ H8

Warranty ...................................... H9

EQUmPNENT

-] Read this manuam carefummyand become famimiar
J

with

...... your

appmications, its mimitations _d any hazards

invomved.

This manuaH contains information for a pressure washer
that operates at 2,200 PSI at a flow rate up to 2.2 gallons
per minute.This high quaHity residentiaH system features

H4" wheeHs, axiaH cam pump with stainHess steeH pistons,
automatic cooH down system, chemicaH iniection system,
variety of nozzHes. IncHudes safety goggHes, heavy duty 25'

hose, and more.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve
the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

pressure washer. Know its

SAFETY RULES

This is the safety amert symbol it is used to
amert you to potentiam personam iniury hazards_
Obey atomsafety messages that fommow this
symbom to avoid possibme iniury or death.

The safety aHert symboH (_) is used with a signaHword

(DANGER, CAUTION,WARNING), a pictoriaH and/or a

safety message to aHert you to hazards. DANGER indicates

a hazard which, if not avoided, will resuHt in death or serious

iniury. WARNmNG indicates a hazard which, if not avoided,

could resuHt in death or serious iniury. CAUTION

indicates a hazard which_ if not avoided_ might resuHt in
minor or moderate iniury. CAUTmON, when used

without the alert symbol indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of iniury or death.

[

Hazard Symbols and Meanings

Toxic Fumes Electrical Shock

Copyright © 2005 Brigs & Stratton Power Products
Group, LLC. AHHrights reserved. No part of this material
may be reproduced or transmitted in any form by any
means without the express written permission of Brigs &
Stratton Power Products Group, LLC.

Slippery Surface

Fire

Moving Parts Hying Obiects

Fail FluidHniection

Explosion Hot Surface

Kickback

Section 1: Safety Rules

WARNING

Operate pressure washer ONLY outdoors,
Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

DO NOT operate pressure washer inside any building or

enclosure.

Use a respirator or mask whenever there is a chance that

vapors may be inhale&

Read all instructions with mask so you are certain the mask w[I[
provide the necessary protection against inhaling harmful vapors.

WARNING

WARNING

WHEN ADDING FUEL

Turn pressure washer OFF and let it cool at least 2 minutes

before removing gas cap,

F{[[fueJ tank outdoors.
DO NOT overfill tank.AIIow space for fue! expansion.

Keep fuel away from sparks, open flames, pilot lights, heat, and
other" ignition sources.

DO NOT light a cigarette or smoke.

VHEN OPERATING EQUIPMENT

• Transport/repair with fuel tank ENPTY or with fuel shutoff
valve OFE

WHEN STORmNG FUEL OR EQUIPMENT WiTH FUEL

IN TANK

Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.

Keep spray nozzle between 8 to 24 inches away from cleaning

SUrface,

Operate this unit on a stable surface.
The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces_
Be extremely careful if you must use the pressure washer from

a ladder; scaffolding or any other relatively unstable location.
Firmly grasp spray gun with both hands when using high

pressure spray to avoid [niury if gun kicks back.

WARNING

When starting engine, pull cord sIow.Jy until resistance is felt

and then puI[ rapidly to avoid kickback.
If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze trigger
on spray gun.

WARNING

NEVER aim spray gun at people, animals or plants.
DO NOT allow CHILDREN to operate pressure washer_
NEVER repair" high pressure hose_ Replace [t_
NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal
Keep high pressure hose connected to pump and spray gun

while system is pressurize&

Squeeze trigger on spray gun to relieve trapped pressure,
every time you stop engine. Engage trigger lock on spray gun.

WARNING

Keep water spray away from electric wiring or fatal electric
shock may result.

O

Section 1: Safety Rules

WARNING

DO NOT touch hot surfaces.
Allow equipment to coo[ before touching.

The pressure washer must be at [east 5 feet from structures
having combustible wails and/or other combustible materials.

Keep at least 3 feet of clearance on all sides of pressure

washer for" adequate cooling, maintenance and servicing.

In the State of California a spark arrester is required by law
(Section 4442 of the California PuNic Resources Code). Other
states may have similar Jaws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester; it must be
maintained in effective working orden

WARNING

. DO NOT wear loose clothing, ieweiry or anything that may

be caught in the starter or" other rotating parts.

. Tie up long hair and remove ]ewelD:

CAUTION

DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.

CAUTION

DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is

running.
NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order:

Always be certain spray gun, nozzles and accessories are
correctly attached.

DO NOT point spray gun at glass when using MAX (pin
point) nozzle,

NEVER aim spray gun at plants.

WARNING

Always wear eye protection when using this equipment or in

vicinity of where equipment is in use,

WARNING

WHEN ADJUSTING OR MAKING REPAiRSTOYOUR
PRESSURE WASHER

Disconnect spark plug wire from spark plug and place wire

where it cannot contact spark plug.

If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.
NEVER operate units with broken or missing parts, or

without protective housing or covers.

DO NOT by-pass any safety device on this machine.
Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

1

NEVER move machine by pulling on high pressure hose. Use
handle provided on unit.

Check fuel system for leaks or"signs of deterioration, such as
chafed or" spongy hose, loose or missing damps, or damaged

tank or cap. Correct all defects before operating pressure

washerL

This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. ff equipment is used

with parts that DO NOT comply with minimum specificadons,

user assumes all risks and liabilities.

Features and ControJs

KNOWYOUR PRESSURE WASHER

Read this owner's rnanuaJ and safety fumes before operating your pressure washer,

Compare the ilhstrations with your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.

Spray Gun

AccessoryTray

Nozzle Extension

with Quick

Air Filter

Primer Bulb

Throttle Lever

Accessory Tray -- Providesconvenient storage for
standard and optional accessories,such as brushes,turbo

wands,etc.
Air FiJter -- Protects engine by filtering dust and debris

out of intake air.

Automatic Cool Down System -- Cycles water
through pump when water reaches 125°. 155°E'Warm

water will discharge from pump onto ground.This system
prevents internal pump damage.

Chemical injection Siphon/Filter -- Use to siphon
detergent or other pressure washer chemicals into the low

pressure stream.

[)ataTag (not shown, near rear of base pJate) -
Provides model and serial number of pressure washer.
Please have these readily available if calling for assistance.

FueJ Tank -- Fill tank with regular unleaded fuel.Always

leave room for fuel expansion.

High Pressure Hose -- Connect one end to water

pump and the other end to spray gun.

Turbo Nozzle

Proj ectProTM
Nozzles

High Pressure Hose

_i psti ck

High Pressure Outlet

& VVater Inlet

Chemical Injection

Pump equipped with

Automatic Cool Down System

High Pressure OutJet -- Connection for high pressure
hose.

Nozzle Extension with Quick Connect --Allows you
to switch between four different nozzles.

OiJ FiJJ/Dipstick -- Check and fill with oil here.
Primer BuJb -- Prepares a cold engine for starting.

Pump -- Develops high pressure.
RecoiJ Starter -- Used for starting the engine manually.

Spray Gun -- Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock.

ProjectPro TMNozzJes -- Detergent, Max, General, and
Delicate nozzles: for various pressure cleaning applications.

ThrottJe Lever -- Sets engine in starting mode for recoil

starter and stops a running engine.
Turbo NozzJe -- Rotates a high pressure stream in a

rapid circular pattern.
Water JnJet -- Connection for garden hose.

ASSEMBLY

iMPORTANT: Read entireowner'smanuaH beforeyou

attempt to assemble or operate your new pressure washer.

Remove Pressure Washer From

H. Remove the parts bag, accessoNes, and inserts incHuded

with pressure washer.

2. SHice two corners at the end of carton from top to
bottom so the paneH can be folded down fiat.

3. Remove pressure washer from carton.

Carton Contents

items in the carton include:

Hain Unit
Handle

High Pressure Hose
Spray Gun

NozzHe Extension with Quick Connect Fitting
PHasticAccessory Tray

Safety Goggles
OH Bottle

Turbo Nozzle with Quick Connect

Parts Bag (whch incHudes the following):

Owner's HanuaH
Engine HanuaH

Owner's Registration Card
Bag containing 4 muHti-coHored ProjectPro TM

NozzHes

HandHe/Tray Fastening Hardware Kit (which

includes):

Carriage Bolts (2)
"L" BoHt

PHasticKnobs (3)

Tree CHips (4)

PREPARING PRESSURE

WASHER FOR USE

If you have any probHems with the assembHyof your
pressure washer or if parts are missing or damaged, call the
pressure washer heHpHineat J=888=6 [ J=67@8. [f caHHingfor

assistance, pHeasehave the model revision, and seriaH

number from the data tag available.

To prepare your pressure washer for operation, you
will need to perform these tasks:

H. Firthout and send in registration card.

2. Attach handHe to main unit, then attach accessory tray
to handHe.

3. Add oiH to engine crankcase.

4. Add fueH to fueH tank.

S. Connect high pressure hose to spray gun and pump.

6. Connect water suppHy to pump.

7. Attach nozzHe extension to spray gun.

8. SeHect/attach quick connect ProjectPro TM nozzHe to
nozzHe extension.

Attach Handle and Accessory Tray

H, Place handle onto handle supports connected to main

unit. Hake sure holes in handle aHignwith holes on
handle supports (Figure H).

NOTE: It may be necessary to move the handHe supports
from side to side in order to aHignthe handHeso it wiHHsHide
over the handHe supports,

O

Section 3: Assembly

2. Insert carriage boks through holes from outside of unit
and attach a phstic knob from insNe of unit (Figure 2).
Tighten by hand.

%

3. Phce accessorytray over holes on hande (viewing
from front of uniO. Pushthe tree clips into the holes
until they sit fiat againstthe accessory tray (Figure 3).

/

4. Insert"L" hook through hole just above billboard on
left side of handle (viewing from front of unit). Hold
hook in place and attach a plastic knob from inside of
unit (Figure 4).Tighten by hand.

SprayGun Hook

5. Insert multi-colored ProjectPro TMnozzles and other
supplied accessories in spaces provided in accessory

tray, See "How to Use AccessoryTray'.

Add Engine Oil and Fuel

° Place pressure washer on a [eve[ surface,

Refer to engine manual for oil and fuel fill information.

- Damage to equipment resuking from failure to follow this
instruction will void warranty.

" Refer to engine owner's manual and follow oil and fuel

recommendations and instructions,

NOTE: Check oil often during engine break-in, Refer to

engine owner's manual for recommendations,

O

Section 3: Assembly

Connect Hose and Water Supply to

iMPORTANT: To avoid pump damage, you must assemble
the nozzle extension to the spray gun and attach all hoses
before you s_art the engine.

NOTE: Remove and discard the shipping caps from the
pumps high pressure outlet and water inlet before

attaching hoses.

I. Uncoil high pressure hose and at_ch one end of hose

to base of spray gun (Figure S).Tighten by hand.

hose here

2. Attach other end of high pressure hose to high
pressure outlet on pump (Figure 6).Tighten by hand.

4. Run water through your garden hose for 30 seconds
to clean out any debris.

mMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

5. Connect the garden hose (not to exceed 50 feet in
length) to the water inlet.Tighten by hand (Figure 7).

Damage to equiprnen_: resulting from failure to follow this

instruction will void warranty_

Turn ON the water and squeeze the trigger on the
gun to purge the pump system of air and impurities.

WANNING

AIw,ayswear eTe protection when using this equipment or in

vicinity of where equipment is in use.

Before starting the pressure washer,be sure you are wearing

adequate eye protection.

Before connecting garden hose to water inlet, inspect
inlet screen (Figure 7). Clean screen if it contains
debris or have it replaced if damaged. DO NOT RUN

PRESSUP_EWASHER IF INLET SCREEN IS DAHAGED.

Inspect inlet

screen_ DO NOT

use if damaged;

clean if dirty.

Checklist Before Startin EgLEn ine

Review the unit's assembly to ensure you have performed

all of the following.

I. Hake sure handle is in place and secure.

2. Check that oil has been added to proper level in the

engine crankcase.

3. Add proper fuel to fuel tank.

4. Check for properly tightened hose connections.

5. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.

6. Provide a proper water supply at an adequate flow.

7. Be sure to read "Safety Rules" and "HowTo UseYour
Pressure _A/asher" before using pressure washer.

O

Operation

HOWTO USEYOUR

PRESSURE WASHER

If you have any problems operating your pressure washen
please call the pressure washer heIpline at 1-888-611-6708.

Pressure Washer Location

Pressure Washer Cmearance

WANNING

Operate pressure washer ONLY outdoors.
Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

DO NC)T operate pressure washer inside any holding or

endosure_

The pressure washer must be at least 5 ft. (I 52 cm) from
structures having combustible walls and/or other
combustible materials. Leave at least 3 ft. (92 cm) all around
pressure washer including overhea& for adequate cooling,
maintenance and servicing.

Place pressure washer in a well ventilated area, which will
allow for removal of deadly exhaust gas. DO NOT place

pressure washer where exhaust gas could accumulate and
enter inside or be drawn into a potentially occupied

building. Ensure exhaust gas is kept away from any
windows, doors, ventilation intakes or other openings that

can allow exhaust gas to collect in a confined area
(Figure 8). Prevailing winds and air currents should be taken

into consideration when positioning pressure washer.

How to StartYour Pressure Washer

To start your pressure washer for the first time, follow
these instructions step-by-step.This starting information

also applies if you have let the pressure washer sit idle for
at least a day.

I. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

3.2 gallons per minute and no less than 20 PSI at
pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See "Preparing Pressure VVasher

for Use" for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

• Damage to equipment resulting from failure to follow this
instruction will void warranty.

5. Attach nozzle extension to spray gun (Figure 9).
Tighten by hand.

6. Choose desired ProjectPro TMnozzle, pull back nozzle
extension collar, insert nozzle and release collar.Tug on

nozzle to make sure it is securely in place (Figure I 0).

See "How to Use ProjectPro TMNozzle System".

/

Typical Pressu_ e
Washe_ Shown

Exhaust Port

/

/

/

7. Engage trigger loci< on spray gun trigger (Figure I I).

O

Section 4: Opecation

Start engine according to instructions given in engine

owner's manuaH.AHso see operating instructions tag
Hocated on the pressure washer.

, WARNING

When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.
Hfengine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze trigger

on spray gun.

NOTE; Always keep the throttle lever in the "Fast"

)osition when operating the pressure washer.

WARNING

WARNING

1

Keep high pressure hose connected to pump and spray gun

while system is pressurized.

Squeeze trigger on spray gun to rdieve trapped pressure,
every time you stop engine. Engage trigger lock on spray gun.

4. Engage trigger Hock on spray gun when not in use.

The unit is equipped with an accessory tray with pHacesto

store your spray gun, nozzHeextension, turbo nozzle, and
ProjectPro TM nozzHes.There is aHsoa hook at the front of

the accessory tray to hoHdyour high pressure hose.

NOTE:The extra hoHe in the tray is for storing a utility
brush.The brush is NOT incHuded with your pressure

washer.You can buy the brush as an optionaH accessory.

H. PHacenozzHeextension through hoHeon accessory tray,

as shown in Figure H2.

DO NOT touch hot surfaces,
Allow equipment to coot before touching.

The pressure washer must be at least 5 feet from structures

having combustible walls and/or other combustible materials.
Keep at least 3 feet of clearance on all sides of pressure

washer for adequate coding, maintenance and servicing.

Hnthe State of California a spark arrester is required by law
(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. [f you equip the muffler with a spark arrester; it must be
maintained in effective working order:

How to Stoj Your Pressure Washer

H. Let engine idHe for two minutes.

2. Turn engine off according to instructions given in

engine owner's manual

3. Squeeze trigger on spray gun to relieve trapped

pressure in hose to avoid iniury.

NOTE: A smaHH amount of water wiHHsquirt out when
pressure is reHeased.

2. PHacespray gun through hoHeon accessory tray on

right side of unit (Figure H2).

NOTE:You may aHso use the hooks attached to the base

and handHe to store your gun and nozzHe extension, as

shown on page 5.

3. Push turbo nozzHe up and into chip on accessory tray

untiH it snaps in, as shown in Figure H2.

4. Hang high pressure hose on hook attached to accessory

tray on front of tray, as shown in Figure H2.

Section 4: Operation

Now to Use ProiectPro TM Nozzle

System

The quick-connect on the nozzie extension allows you to
switch between four different ProiectPro TM system nozzHes.
The ProiectPro TM nozzHes vary the pressure and spray

)attern as shown (Figure i 3).

Low Pressure

Bhck

Use to appiy

detergent

High Pressure

\

i

Delicate General Max

40 ° Yellow 15° Orange 0 ° Red

1650 PSI 1950 PSI 2200 PSI

2.2 GPH 2.1 GPH 1.9 GPH

Fommow these instructions to change ProiectPro rM

nozzmes:

i. Engage trigger Hock on spray gun.

2. Puil back collar on quick-connect and puil current

ProjectPro TM nozzle off. Store ProjectPro TM nozzles in
holder provided on the accessory tray.

3. Select desired ProiectPro TM nozzie:

For delicate rinse (iower pressure and higher

flow), for gentile cieaning of cars/trucks, boats, RV's,

patio furniture, lawn equipment, etc., select yellow

Delicate ProjectPro TM nozzle (Figure 14).

For general rinsing (medium pressure and medium

flow), ideal for most aH purpose cieaning such as

home siding, brick patios, wood decks, driveways

and sidewalks, garage floors, etc., select orange

General ProjectPro TM nozzle (Figure i5).

CAUTION m

" NEVER exchange ProiectPro nozzles without locking the

trigger lock on the trigger.

, DO NOT twist ProiectPro TMnozzles while spraying.

TM