TROY BILT 020207 User Manual

6

ASSEMBLY

IMPORTANT: Read entire owner’s manual before you

attempt to assemble or operate your new pressure washer.

Remove Pressure Washer from

Carton

• Remove the parts bag, accessories, and insert included
with pressure washer.

• Slice two corners at the end of carton from top to
bottom so the panel can be folded down flat, then
remove all packing material.

• Roll pressure washer out of carton.

Carton Contents

Items in the carton include:

• Main Unit

• Goggles

• Handle

• High Pressure Hose

• Spray Gun

• Nozzle Extension

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Engine Manual

• Owner’s Registration Card

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolts (2)

• Plastic Knobs (4)

• “L” Hooks (2)

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your
pressure washer or if parts are missing or damaged, call the
pressure washer helpline at 1-888-611-6708. If calling for
assistance, please have the model, revision, and serial
number from the model data decal available.

To prepare your pressure washer for operation, you
will need to perform these tasks:

1. Fill out and send in registration card.

2. Attach handle to main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

Attach Handle

1. Place handle assembly onto handle supports connected
to main unit. Make sure holes in handle align with holes
on handle supports (Figure 1).

NOTE: It may be necessary to move the handle supports
from side to side in order to align the handle so it will slide
over the handle supports.

2. Insert carriage bolts through holes from outside of unit
and attach a plastic knob from inside of unit (Figure 2).
Tighten by hand.

3. Insert one “L” hook through hole just above billboard
on left side of handle (viewing from front of unit).Hold
hook in place and attach a plastic knob from inside of
unit (Figure 3).Tighten by hand.

4. Insert other “L” hook through hole just below
billboard on right side of handle (viewing from front of
unit). Hold hook in place and attach a plastic knob
from inside of unit (Figure 3).Tighten by hand.

Align Holes

Handle

Handle

Supports

Figure 1 — Attach Handle to Base

Figure 2 — Secure Handle

3

Section

Assembly

NO Tools Required for Assembly

Required Assembly Tools

17

TROUBLESHOOTING

Troubleshooting

7

Section

Problem Cause Correction

Pump has following problems:
failure to produce pressure,
erratic pressure, chattering, loss
of pressure, low water volume.

1. Nozzle in low pressure mode.

2. Water inlet is blocked.

3. Inadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose strainer.

6. Water supply is over 100°F.

7. High pressure hose is blocked or
leaks.

8. Gun leaks.

9. Orifice is obstructed.

10. Pump is faulty.

1. Pull nozzle backward for high
pressure mode.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch leak.

5. Check and clean inlet hose
strainer.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace gun.

9. Clean orifice.

10. Contact Authorized service facility.

Detergent fails to mix with spray.

1. Detergent siphoning tube is not
submerged.

2. Chemical filter is clogged or
cracked.

3. Dirty in-line filter.

4. Nozzle is in high pressure mode.

1. Insert detergent siphoning tube
into detergent.

2. Clean or replace filter/detergent
siphoning tube.

3. See "Check In-Line Filter".

4. Push nozzle forward for low
pressure mode.

Engine runs good at no-load but
"bogs" when load is added.

Engine speed is too slow. Move throttle control to FAST

position. If engine still "bogs down",
contact Authorized service facility.

Engine shuts down during
operation.

Out of gasoline. Fill fuel tank.

18

Notes

TROY-BILT® OWNER WARRANTY POLICY Effective November 12, 2003

WARRANTY PERIOD*

* The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the
period of time stated in the table above. "Consumer use" means personal residential household use by a retail consumer.
"Commercial use" means all other uses, including use for commercial, income producing or rental purposes. Once equipment has
been used commercially, it shall thereafter be considered to be in commercial use for purposes of this warranty.

** The engine and starting batteries are warranted solely by the manufacturers of those products.

WARRANTY REGISTRATION IS NOT NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON POWER
PRODUCTS EQUIPMENT. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE
INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED,THE MANUFACTURING DATE OF THE
EQUIPMENT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

About your equipment warranty:

We welcome warranty repair and apologize to you for being inconvenienced.Any Authorized service dealer may perform warranty
repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For
example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping,
handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the
equipment has been removed or the equipment has been altered or modified. During the warranty period, the Authorized service
dealer, at its option,will repair or replace any part that, upon examination, is found to be defective under normal use and service.This
warranty will not cover following repairs and equipment:

• Normal Wear: Outdoor power equipment, like all mechanical devices, needs periodic parts, service and replacement to perform

well.This warranty does not cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or

unauthorized installation or alteration and modification, misuse, negligence, accident, overloading,overspeeding, improper
maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability.This warranty also does
not cover normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime,
etc.).

• Other Exclusions: Also excluded from this warranty are wear items such as quick couplers,oil gauges, belts, o-rings, filters,

pump packing, etc., pumps which have been run without water supplied or damage or malfunctions resulting from accidents,
abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration.Accessory parts such as guns,
hoses, wands and nozzles are excluded from the product warranty.Also excluded is used, reconditioned, and demonstration
equipment; equipment used for prime power in place of utility power and equipment used in life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

LIMITED WARRANTY

“Troy-Bilt® is a registered trademark of Troy-Bilt, LLC and is used under license to Briggs & Stratton Power Products.Briggs &
Stratton Power Products will repair or replace, free of charge, any part, or parts of the equipment** that are defective in material
or workmanship or both.Transportation charges on parts submitted for repair or replacement under this warranty must be
borne by purchaser.This warranty is effective for the time periods and subject to the conditions provided for in this policy. For
warranty service, find your nearest Authorized service dealer by calling 1-888-611-6708.Warranty service may only be performed
by a Briggs & Stratton Power Products Authorized service dealer.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TIME PERIOD SPECIFIED, OR TO THE EXTENT PERMITTED
BY LAW.ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER
ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some countries or
states do not allow limitations on how long an implied warranty lasts, and some countries or states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.This warranty gives
you specific legal rights and you may also have other rights that vary from country to country or state to state.”

Equipment ** Consumer Use Commercial Use

Pressure Washer 1 Year 90 Days

Portable Generator 2 Years (2nd year parts only) 1 Year