TTP 1 E / TTP 2 E
EN
OPERATING MANUAL
DEHUMIDIFIER
TRT-BA-TTP1E-TTP2E-TC-001-EN
Table of contents
Notes regarding the operating manual................................. 1
Safety .....................................................................................1
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
Information about the device................................................3
Transport and storage...........................................................4
Assembly and installation.....................................................4
Operation ...............................................................................5
Errors and faults....................................................................6
Maintenance ..........................................................................6
Technical annex.....................................................................8
Disposal .................................................................................8
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Notice
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
TTP 1 E
https://hub.trotec.com/?id=41306
TTP 2 E
https://hub.trotec.com/?id=41307
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not sit on the device.
1 EN
Operating manual – dehumidifier TTP 1 E / TTP 2 E
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk.
• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Ensure that the air inlet and outlet are not obstructed.
• Ensure that the side of the device where the air inlet is
found is kept free of dirt and loose objects.
• Only transport the device in an upright position with an
emptied condensation tank or drain hose.
• Discharge the collected condensate before transport and
storage. Do not drink it. Health hazard!
Intended use
Only use the device for keeping the room air in spatially limited
areas dry whilst adhering to the technical data.
Intended use includes keeping the following dry:
• small living spaces
• closets and shoe cabinets
• bookshelves
• pantries and storerooms
• small, windowless bathrooms etc.
Improper use
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device outdoors.
• Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Behaviour in the event of an emergency
1. Switch the device off.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
EN 2
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Information about the device
7
6
1
2
5
3
4
Description of the device
The device uses the principle of condensation and a Peltier
element to dehumidify small rooms in a silent manner.
The fan sucks in damp room air through the air inlet. The room
air is cooled at the cold side of the Peltier element until it is
below the dew point. Water vapour contained in the room air
precipitates as condensation or rime. The dehumidified, cooled
air is blown out. The drier air thus conditioned mixes with the air
in the room. The humidity in the room where the device is
positioned is reduced as air constantly circulates through the
device.
Depending on the air temperature and the relative humidity, the
condensed water drops into the condensation tank. The latter is
fitted with a float to measure the filling level.
If the maximum level of the condensation tank is reached or if
the float is not correctly positioned, the indicator LED flashes
red. The device switches off. The indicator LED only goes out
again once the emptied condensation tank is reinserted.
The functioning of the two devices is identical, they merely
differ in appearance or to be precise in colour: The device TTP 1
E is brown and the device TTP 2 E is white.
Device depiction
No. Designation
1 Air outlet
2 Air inlet
3 Condensation tank
4 Power adapter
5 Power adapter connection
6 Indicator LED:
illuminated blue when the device is ready for operation
flashes blue if the power adapter is defective
flashes red when the water tank is full or the float is
incorrectly positioned
7 On/off switch
3 EN
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Transport and storage
A
B
C
C
D
Assembly and installation
Notice
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• Do not use the power cable to drag the device.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.
Storage
Before storing the device, proceed as follows:
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• Empty and clean the condensation tank prior to storage.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust if necessary
• Place no further devices or objects on top of the device to
prevent it from being damaged.
Scope of delivery
• 1x Device
• 1 x Power adapter
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Set the device up in an upright and stable position.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• When positioning the device, keep a sufficient distance to
heat sources.
EN 4
Operating manual – dehumidifier TTP 1 E / TTP 2 E
• Make sure that no curtains or other objects interfere with
7
6
the air flow.
• When positioning the device, particularly in wet areas,
secure it locally with an RCD (residual current device)
which complies with the respective regulations.
Inserting the condensation tank
• Ensure that the float inside the condensation tank is
inserted correctly.
• Ensure that the condensation tank is empty and inserted
correctly.
Connecting the power adapter
• Plug the power adapter cable into the device's mains
connection.
Operation
• Avoid open doors and windows.
• After being switched on, the device operates fully
automatically.
Operating elements
No. Designation
6 Indicator LED:
illuminated blue when the device is ready for operation
flashes blue if the power adapter is defective
flashes red when the water tank is full or the float is
incorrectly positioned
7 On/off switch
• Plug the power adapter into a properly fused mains socket.
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
1. Press the on/off switch(7).
ð The LED at the on/off switch is illuminated in blue.
ð The fan switches on.
ð The device starts to dehumidify.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Empty the condensation tank, if need be.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
5 EN
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Check the power adapter. If the indicator LED(6) flashes
blue, the power adapter is defective and must be replaced.
• Check the condensation tank for correct seating.
• Check whether the condensation tank is full. The indicator
LED (6) flashes red.
• Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
• Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is running, but there is no formation of
condensate:
• Check the float in the condensation tank for dirt. If
necessary, clean the condensation tank. The float must be
able to move freely.
• Check the room temperature. Observe the device's
permissible ambient temperature according to the
technical data.
• Ensure that the relative room humidity complies with the
technical data.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Visual inspection of the inside of the device for dirt
1. Use a torch to illuminate the openings of the device.
2. Check the inside of the device for dirt.
3. If you see a thick layer of dust, have the inside of the
device cleaned by a specialist company or by Trotec.
The device is loud or vibrates:
• Check whether the device is set up in a stable and upright
position.
Condensate is leaking:
• Check the device for leaks.
The device gets very warm, is loud or loses power:
• Check the air inlets for dirt. Remove external dirt.
• From the outside, check the device for dirt (see chapter
Maintenance). If the inside of the device is dirty, have it
cleaned by a specialist company or by Trotec.
Notice
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
EN 6
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Emptying the condensation tank
If the condensation tank is full or the float is not correctly
positioned, the indicator LED(6) flashes red and the device
switches off.
1. Take the condensation tank out of the device.
4. Refit the condensation tank into the device.
Make sure not to damage the float when inserting or
removing the condensation tank.
In doing so, make sure that the float is positioned
correctly.
In doing so, make sure that the condensation tank is
inserted correctly, for otherwise the device cannot be
switched back on.
2. Empty the condensation tank over a drain or sink.
3. Rinse the tank with clear water. Clean the tank regularly
using a mild cleaning agent (no detergent!).
Activities required after maintenance
If you want to continue using the device:
• Reconnect the device to the mains.
If you do not intend to use the device for a considerable time:
• Store the device according to the Storage chapter.
7 EN
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Technical annex
Technical data
Parameter Value
Model TTP 1 E / TTP 2 E
Max. dehumidification
performance
Ambient temperature 16°C to 35°C
Mains connection
Output
Power consumption 22 W
Nominal current 2.5 A
Condensation tank capacity 500 ml
Sound pressure level (1m
distance)
Dimensions (depth x width x
height)
Minimum distance to walls and
other objects
top (A):
rear (B):
sides (C):
front (D):
Weight 1 kg
220 ml / 24 h
Power adapter
Input
100 V – 240 V / 50 – 60 Hz
DC 9 V / 2.5 A
35 dB(A)
95 x 150 x 220 mm
10 cm
10 cm
10 cm
10 cm
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
EN 8
Operating manual – dehumidifier TTP 1 E / TTP 2 E
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
Loading...