How it Works
Trotec
Loading...
TIH 350+
Operating Manual
14 pgs2.13 Mb0
Table of contents
Loading...

Trotec TIH 350+, TIH 650+ Operating Manual

Download
Page 1
TIH 350+ / TIH 650+
EN
OPERATING MANUAL
INFRARED HEATING PANEL
TRT-BA-TIH350+_TIH650+-TC2018-53-001-EN
Page 2

Table of contents

You can download the current version of the operating manual and the EU declaration of conformity via the following link:

Notes regarding the operating manual

Symbols

Warning of electrical voltage
This symbol indicates dangers to the life and health of persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of persons due to hot surface.
Warning
This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
Note
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the operating manual must be observed.
TIH 350+
https://hub.trotec.com/?id=42748
TIH 650+
https://hub.trotec.com/?id=42749

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use!
Warning Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference.
This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Warning
Children of less than 3years should be kept away unless continuously supervised. Children aged from 3years and less than 8years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3years and less than 8years shall not plug in, regulate and clean the appliance or perform user maintenance.
2 EN
infrared heating panel TIH 350+ / TIH 650+
Page 3
Warning
Do not use the device in small rooms if persons are present who cannot leave the room independently and who are not under constant supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• The electrical connection must correspond to the specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains socket.
• Observe the device's power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload.
• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.
• Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk!
• During the installation of the device observe the minimum distances from walls and other objects as well as the storage and operating conditions specified in the Technical data chapter.
• Never drill into the heating panel.
• Do not use the device in immediate proximity to curtains.
• Do not place the device on combustible ground.
• Do not transport the device during operation.
• Allow the device to cool down before transport and/ or maintenance work.
• Do not use this device near bathtubs, shower trays, swimming pools or other water containers. Risk of electric shock!

Intended use

Use the device TIH 350+/ TIH 650+ for heating walls to assist the drying process as part of water damage restoration.
Only use the device in interior spaces.

Improper use

• Do not place any objects, e.g. clothing, on the device.
• Do not use the device for heating in vehicles.
• Do not use the device for heating rooms.
• Do not use the device out of doors.
• Do not use this device in the vicinity of fuel, solvents, varnishes or other easily inflammable vapours or in rooms where these substances are stored.
• The device may not be used as a heating device for babies / children or animals.
• The device may not be installed inside a shower or directly above a bathtub.
• The device must not be used near swimming pools.
• Do not use this device in the immediate vicinity of sinks, bathtubs or other water containers.
Never immerse the device in water.
• Any operation other than as described in this manual is prohibited. Non-observance renders all claims for liability and guarantee null and void.
Any unauthorised changes, modifications or alterations to the device are forbidden.

Personnel qualifications

People who use this device must:
• be aware of the dangers that occur when working with electric devices in damp areas.
• have read and understood the operating manual, especially the Safety chapter.
Maintenance tasks which require the housing to be opened must only be carried out by specialist electrical companies or by Trotec.
EN 3
infrared heating panel TIH 350+ / TIH 650+
Page 4

Symbols on the device

Symbols Meaning
This symbol located on the device indicates that it is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device. In order to avoid overheating and fire hazards, the heater must not be covered.
This symbol located on the device indicates that it is prohibited to spray the device.
This symbol located on the device indicates dangers to the life and health of persons due to hot surface.

Residual risks

Warning of electrical voltage
Work on the electrical components must only be carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning of hot surface
Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present!
Warning of hot surface
The surface of the device warms up during operation. Do not touch the device surface during operation and observe the minimum distance!
Warning
Risk of injury due to infrared radiation! Do not stay in the device's immediate vicinity for too long. Do not look directly into the device for too long. Observe the minimum distances.
Warning
Improper installation entails a risk of fire. Do not place the device on combustible ground. Do not place the device on high-pile carpets.
Warning
In order to avoid overheating and fire hazards, the heater must not be covered.

Behaviour in the event of an emergency

1. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket.
2. Do not reconnect a defective device to the mains.

Overheating protection

The device is provided with a safety thermostat which is activated by overheating of the device (when exceeding the operating temperature).
Once the safety thermostat has switched itself on, the device will be turned off.
When the device has cooled down sufficiently, the heating will be switched back on.
If the safety thermostat does not switch in the event of overheating, the overheating protection will be tripped. In that case the device switches off completely. If so, please contact the customer service to have the overheating protection replaced.
Warning
Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the hands of children.
Warning
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
4 EN
infrared heating panel TIH 350+ / TIH 650+
Page 5

Information about the device

Device description

The device serves for drying selective water damages on walls. For damages located above floor level up to two further devices may be mounted on top of the first panel using the set of stacking handles TIH350+/650+ from the available accessories.
To irradiate higher wall surfaces, you can use the set of assembly support fastening clamps and the assembly supports connection set 350+ or 650+ from the available accessories as well as suitable assembly supports.
The device is fitted with a MID-certified energy consumption meter and thus qualified for billing purposes. The meter indicates the energy consumed so far. It cannot be reset. An LED indicates that the panel is switched on and the energy meter captures the energy consumption.
In accordance with calibration regulations, restoration companies are so-called "meter users" or "users of measurement readings", which binds them to observe the German Weights and Measures Act (MessEG). The MessEG regulates the recording and transfer of measurement readings based on which the power consumption costs of the devices shall be determined.
Radiation
The wavelength of the thermal radiation produced by the devices TIH 350+/ TIH 650+ lies within the IR-Crange. The wavelength depends on the respective surface temperature of the heating panel and thus on the ambient temperature in the room where the heating panel is set up. At 75°C= 8.3μm, at 85°C= 8.1μm, at 95°C= 7.9μm (according to Wien's displacement law). Thanks to such mild IR-C radiation, there is no risk of eye damage.
What is infrared radiation?
Infrared radiation is a natural type of radiation and for instance part of solar radiation. It is heat radiation, regardless of how this heat is generated. Every object whose temperature lies above the absolute zero (-273°C) emits energy in the form of electromagnetic radiation.
The wavelength of the infrared radiation is determined by the temperature of the radiating object. If infrared rays hit the surfaces of other objects, the stored energy is released in the form of heat. The heat transfer takes place through conductivity, convection or radiation. In any case, the decisive factor is the temperature difference.
EN 5
infrared heating panel TIH 350+ / TIH 650+
Page 6

Device depiction

1
2
3
4
5
1
2
3
4
5
TIH 350+
TIH 650+
No. Designation
1 foot
2 energy consumption meter
3 electric control box
4 power cable with plug
5 radiating side
6 EN
infrared heating panel TIH 350+ / TIH 650+
Page 7

Transport and storage

7
6

Assembly and installation

Note
If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.

Transport

Before transporting the device, observe the following:
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not use the power cable to drag the device.
• Allow the device to cool down sufficiently.

Storage

Before storing the device, proceed as follows:
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Allow the device to cool down sufficiently.
When the device is not being used, observe the following storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• Place no further devices or objects on top of the device to prevent it from being damaged.

Scope of delivery

• 1x Device
• 1x Manual
• 2 x Foot

Unpacking the device

1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

Assembly

Upon delivery the device TIH 350+/ TIH 650+ is already partially preassembled. The feet still need to be mounted.
Mounting the feet
Info
The assembly of the feet is identical for both devices TIH350+ and TIH650+.
Please proceed as follows to assemble the feet at the device:
1. Detach the feet from the heating panels.
ð Fold the feet outwards and away from the device. Make
sure that the bolt of each foot(7) disengages from the locking device(6).
2. Position the device either upright or horizontally as desired.
EN 7
infrared heating panel TIH 350+ / TIH 650+
Page 8
3. Attach the feet to the respectively correct side of the
8
device.
4. Make sure that the feet's connection bars fit properly into the openings at the device.
Stacking devices (optional)
The device can only be stacked using the set of stacking handles from the available accessories. To do so, please observe the information supplied with the stacking handles.
TIH 350+ and TIH 650+ can be combined in any desired
stacking order.
5. Check that the spring bolt(8) securely locks into place.
Caution
Risk of injury! Ensure the secure footing and stable positioning of the stacked installation. Provide additional safety measures if required.
Assembly for irradiating higher wall surfaces (optional)
The devices can only be properly mounted for irradiating higher wall surfaces by use of the fastening clamps and the assembly supports connection set from the available accessories. Suitable assembly supports are also required.
8 EN
infrared heating panel TIH 350+ / TIH 650+
Page 9

Positioning

A
B
C
C
D
A number of spatial and technical conditions have to be considered for the selection of the device's installation site. Non-observance may impair the proper functioning of the device or the accessories or can entail risks of personal injury and property damage.
• Set the device up in an upright and stable position.
• Make sure that there are no curtains or similar objects in the immediate vicinity.
• Set the radiator up in a way that the radiating side(5), i.e. the dark side, points towards the surface to be dried. If the feet touch the wall, the distance between panel and wall is optimal.
Do not install the device directly in front of a wall socket. The socket should be located next to the device.
• When using more than 3infrared panels, please use separate circuits.
• The devices can be installed both upright and horizontally.

Start-up

When positioning the device, observe the minimum distance from walls or other objects as described in the Technical data chapter.
• Always set the infrared heating panel up in a way that the dark, radiating side(5) faces a wall. The distance to the wall may amount to maximally 20cm.
• Observe any regulations applicable for the installation site during the set-up of the infrared heating panel.
• Before restarting the device, check the condition of the power cable. If there are doubts as to the sound condition, contact the customer service.
• Set the device up in an upright and stable position.
• Do not create tripping hazards when laying the power cable or other electric cables, especially when positioning the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• Make sure that there are no curtains or similar objects in the immediate vicinity.
Connecting the power cable
• Insert the mains plug into a properly secured mains socket.
EN 9
infrared heating panel TIH 350+ / TIH 650+
Page 10

Operation

9

Available accessories

• Avoid open doors and windows.
Energy consumption meter
The MID-certified energy consumption meter flashes once with every watt consumed.
No. Designation
9 Indication of the energy consumption
Switching the device on
Once you have completely installed or positioned the device as described in the chapters Start-up and Positioning, you can switch it on:
1. Plug the mains plug into a sufficiently fused mains socket. ð The energy consumption meter(2) lights up.
Warning
Only use accessories and additional equipment specified in the operating manual. Using insertion tools or accessories other than those specified in the operating manual may cause a risk of injury.
Accessories Article number
Set of stacking handles
1.410.003.009
TIH350+/650+
Assembly supports
1.410.003.007
connection set 350+
Assembly supports
1.410.003.003
connection set 650+
Set of assembly support
1.410.003.004
fastening clamps
Transport bag TIH650+ 1.410.003.005
Socket thermostat BN30 6.100.007.009
Socket thermostat BN35
6.100.007.008
for TIH+
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
1. Hold onto the mains plug while pulling the power cable out
of the mains socket.
ð The energy consumption meter(2) goes out.
2. Allow the device to cool down completely.
3. Clean the device according to the Maintenance chapter.
4. Store the device according to the Storage chapter.
10 EN
infrared heating panel TIH 350+ / TIH 650+
Page 11

Errors and faults

Maintenance

Warning of electrical voltage
Tasks which require the housing to be opened must only be carried out by authorised specialist companies or by Trotec.
The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
The surface of the device bulges outward:
• The material expands due to heating. This is a perfectly
normal process. No measures are required.
The surface of the device only heats up slightly:
• The mains voltage does not meet the requirements. Check
the mains voltage.
• The ambient temperature is low. This is a perfectly normal
process. No measures are required.
The device makes noises after switch-on:
• The material expands due to heating. The insulation
expands as well and might generate noises. This is a perfectly normal process. No measures are required.

Activities required before starting maintenance

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the housing to be opened must only be carried out by authorised specialist companies or by Trotec.

Cleaning the device

Warning of electrical voltage
Never immerse the device in water!
Clean the device with a soft, damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
Note
Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.
Your device still does not operate correctly after these checks?
Please contact the customer service. If necessary, bring the device to an authorized specialist electrical company or to Trotec for repair.
EN 11
infrared heating panel TIH 350+ / TIH 650+
Page 12

Technical annex

(°C)
(W)
(1)
(1)
(2)
(2)
(3)
(3)
(W)
(°C)
(1)
(1)
(2)
(2)
(3)
(3)

Technical data

Parameter Value
Model TIH 350+ TIH 650+
Article number 1.410.003.022 1.410.003.030
Heating capacity at
1
20°C
Power supply 230V/ 50Hz 230V/ 50Hz
Operating range -20°C to 55°C -20°C to 55°C
Max. power input 440 W 820 W
Nominal consump­tion at 20°C
1
Cable length 2 m 2 m
Effective range 0.46 m
Surface temperature 85°C 85°C
Protection type IP44 IP44
Weight 6.5kg 10.7 kg
Dimensions (widthx height2x depth2)
Minimum distance to walls and other objects: A: top B: rear C: side D: front
1
The indicated temperature refers to temperature at the heating
element.
2
without feet
350W 650W
0.3 kWh 0.5 kWh
2
1370x 367x 36 mm
6 cm 6 cm 6 cm 6 cm
0.85 m
1370x 625x 36 mm
6 cm 6 cm 6 cm 6 cm
2
Performance of the TIH350+ depending on the heating film temperature
Performance of the TIH650+ depending on the heating film temperature
Parameter Value
(W) Device performance given in watts
(°C) Heating film temperature in °C
(1) Average
(2) Minimum
(3) Maximum
12 EN
infrared heating panel TIH 350+ / TIH 650+
Page 13

Disposal

The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. For further return options provided by us please refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling and other forms of recovery of waste equipment as well as to prevent negative effects for the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment.
EN 13
infrared heating panel TIH 350+ / TIH 650+
Page 14
Trotec GmbH & Co. KG
Grebbener Str. 7 D-52525 Heinsberg
+49 2452 962-400 +49 2452 962-200
info@trotec.com www.trotec.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use