How it Works
Trotec
Loading...
TFV30
Operating Manual
10 pgs1.42 Mb0
Operating Manual
12 pgs2.58 Mb0
Table of contents
Loading...

Trotec TFV 20, TFV 30 Operating Manual

Download
Page 1
TFV 10 / TFV 20 / TFV 30
EN
OPERATING MANUAL
TURBO FAN
TRT-BA-TFV10-TFV20-TFV30-TC-002-EN
Page 2

Table of contents

You can download the current version of the operating manual and the EU declaration of conformity via the following link:

Notes regarding the operating manual

Symbols

Warning of electrical voltage
This symbol indicates dangers to the life and health of persons due to electrical voltage.
TFV 10
https://hub.trotec.com/?id=39960
TFV 20
https://hub.trotec.com/?id=41941
TFV 30
https://hub.trotec.com/?id=39961
Warning
This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.
Caution
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
Note
This signal word indicates important information (e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the operating manual must be observed.
Wear hearing protection
Information marked with this symbol indicates that you should wear hearing protection.
1 EN
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 3

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use!
Warning Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference.
This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• The electrical connection must correspond to the specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains socket.
• Observe the technical data when selecting extensions to the power cable. Completely unroll the extension cable. Avoid electrical overload.
• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.
• Do not under any circumstances use the device if you detect damages on the mains plug or power cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Defective power cables pose a serious health risk.
• Observe the storage and operating conditions as given in the Technical data chapter.
• Ensure that the air inlet and outlet are not obstructed.
• Make sure that there are no loose items located in the immediate surroundings of air inlet and air outlet.

Intended use

The devices TFV 10/ TFV 20/ TFV 30 may be used for generating a broad near-ground air current with a high air circulation for the accelerated drying of flooring or to assist in drying walls and floors after water damage or else for construction drying. All other applications are considered improper use.

Improper use

The turbo fan is not suited for installation in fluids or on flooded or boggy grounds. Any unauthorised changes, modifications or alterations to the device are forbidden.

Personal protective equipment

Wear hearing protection
Wear appropriate hearing protection when working with the device.

Personnel qualifications

People who use this device must:
• have read and understood the operating manual, especially the Safety chapter.
EN 2
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 4

Residual risks

Warning of electrical voltage
Work on the electrical components must only be carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.
Warning
Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the hands of children.
Warning
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy.
Caution
Risk of injury due to parts being whirled up by the strong air current. Before switching the device on, make sure that there are no loose parts (clothing, hair ...) located near the air inlet or outlet!
Note
Do not use abrasive cleaners or solvents to clean the device.

Information about the device

Device description

The devices TFV 10/ TFV 20/ TFV 30 were designed for a very high air flow rate. They may be used for drying carpets, buildings or screed as well as for the ventilation of poorly accessible intermediate spaces. Owing to the high air circulation, the devices can also be used to control excessive humidity levels. The fan is also very effective for the additional air circulation when heating large buildings, e.g. in the months of winter.
The TFV 20/ TFV 30 are further equipped with a service socket, which means that you can operate another device via the same socket. This socket is ready for operation for as long as the devices TFV 20/ TFV 30 are connected to the mains – they do not need to be switched on.
Moreover, you can connect optional hose distributors to the devices TFV 20/ TFV 30 in order to direct the air current towards different locations.
The cable of this devices TFV 10/ TFV 20/ TFV 30 can be wound around the cable holder at the carrying handle.
The devices TFV 10/ TFV 20/ TFV 30 are designed in a way that several devices can be safely stacked on top of one another for space-saving storage. Do not exceed the maximum of five stacked devices.
In addition to all conventional ventilation tasks these turbo fans are also suited particularly well for the quick elimination of moisture at the underbody after driving on wet roads.
The devices can be set up at different angles in order to reach difficult corners or otherwise inaccessible hollows: 0°, 45°, 90°.

Behaviour in the event of an emergency

1. In an emergency, disconnect the device from the mains feed-in: Switch the device off and disconnect it from the mains.
2. Remove persons from the danger area.
3. Do not reconnect a defective device to the mains.
3 EN
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 5

Device depiction

1
2
3
4
6
7
5
1
11
8
4
3
6
5
7
TFV 10
TFV 20
No. Designation
1 Switch for fan stage selection 2 Operating hours counter 3 Transport handle 4 Air outlet 5 Skids 6 Air inlet 7 Cable holder
No. Designation
1 Switch for fan stage selection 3 Transport handle 4 Air outlet 5 Skids 6 Air inlet 7 Cable holder 8 Service power socket 11 Dual counter (operating and kilowatt hours)
EN 4
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 6
TFV 30
11
9
6
3
6
7
4
8
5

Transport and storage

Note
If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device.

Transport

Before transporting the device, proceed as follows:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not use the power cable to drag the device.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.

Storage

Before storing the device, observe the following:
When the device is not being used, observe the following storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• stackable: up to 5devices may be stacked on top of one another
No. Designation
3 Transport handle 4 Air outlet 5 Skids 6 Air inlet 7 Cable holder 8 Service power socket 9 Rotary switch for fan stages 11 Dual counter (operating and kilowatt hours)
Info
Do not take the devices into operation when stacked. Stacking rules out an efficient usage of the devices.
5 EN
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 7

Assembly and start-up

Scope of delivery

• 1x Device
• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

Assembly

Connecting the (optional) hose distributors
The devices TFV 20/ TFV 30 can be connected to optional hose distributors in order to direct the air current towards different locations.
The device TFV 20 can be used with an optional two-way hose distributor, and the device TFV 30 with an optional three-way hose distributor.
Info
Seal off unused connections by means of suitable sealing caps and possibly with hose clamps to prevent a decrease in the air flow rate.
Info
The procedure of fitting a hose distributor is described below using the example of a three-way hose distributor that is connected to the TFV30; however, it applies accordingly to the TFV20 and a two-way hose distributor.
1. Open the clamps of the three-way hose distributor.
2. Affix the three-way hose distributor at the designated locations at both ends of the air outlet.
3. Make sure that at the bottom the three-way hose distributor is positioned flush with the device.
4. Close both clamps of the three-way hose distributor.
5. Check the clamps and the three-way hose distributor for tight fit.
6. If attached, remove the sealing caps from the three-way hose distributor.
EN 6
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 8
7. Connect suitable hoses to the three-way hose distributor
0°
45°
90°
1
and affix them using an appropriate hose clamp.

Start-up

Positioning
• Set the device up separately and in a stable position.
• The device can be variably positioned in a way to allow an air discharge at an angle of 0°, 45° or 90°.
Connecting the power cable
• Insert the mains plug into a properly secured mains socket.

Operation

Operating elements
TFV 10
No. Designation
1 Switch for fan stage selection
8. Check the hoses for tight fit.
7 EN
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 9
TFV 20
11
10
8
1
9
8
10
11
No. Designation
1 Switch for fan stage selection 8 Service power socket 10 Electricity meter LED 11 Dual counter (operating hours counter and MID-certified
kilowatt hours counter)
TFV 30
Switching the device on
Once you have completely installed the device as described in the Start-up chapter, you can switch it on.
TFV 10
1. Set the selection switch(1) to the desired fan stage. stage1= I stage2= II
ð The device is switched on.
TFV 20
1. Set the selection switch(1) to the desired fan stage. stage1= I stage2= II
ð The device is switched on.
TFV 30
1. Set the rotary switch(9) to the desired fan stage. stage1= LOW stage2= MEDIUM stage3= HIGH
ð The device is switched on.
Dual counter (TFV 20 and TFV 30)
The devices TFV 20/ TFV 30 are equipped with a dual counter(11). The operating hours are indicated in the upper section of the counter, the kilowatt hours are displayed just below. The kWhcounter is certified according to MID. The LED(10) is illuminated as soon as a current flow is established.
No. Designation
8 Service power socket 9 Rotary switch for fan stages 10 Electricity meter LED 11 Dual counter (operating hours counter and MID-certified
kilowatt hours counter)
Using the service socket
The TFV 20/ TFV 30 are equipped with a service socket, which means that you can operate another device via the same socket. The service socket is ready for operation as soon as the devices are connected to the mains – they do not need to be switched on.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Set the fan stage selection switch(1) to position0 (centre) or else the rotary switch(9) to OFF.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
EN 8
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 10

Available accessories

TFV 20
Accessories Article number
Hose adapter (two-way hose
6.100.005.055 distributor, 2x Ø100mm), incl. one sealing cap
Air hose Tronect TF-L,
6.100.001.115 Ø100mm, length 6m
Hose clamp 80 – 130mm 6.100.009.079
TFV 30
Accessories Article number
Hose adapter (three-way hose
6.100.005.061 distributor, 3x Ø100mm), incl. two sealing caps
Air hose Tronect TF-L,
6.100.001.115 Ø100mm, length 6m
Hose clamp 80 – 130mm 6.100.009.079

Errors and faults

The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Wait for 10minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company or by Trotec.
Your device still does not operate correctly after these checks?
Please contact the customer service. If necessary, bring the device to an authorized specialist electrical company or to Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.

Cleaning the housing

Clean the housing with a soft, damp and lint-free cloth. Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.

Cleaning the fan and device interior

• Check fan and protective grid for perfect condition before and after each application.
• Clean the fan after each operation.
• Use compressed air to remove particles, lint, dust and dirt from motor, fan wheel and protective grid. Do not in any event use a high-pressure cleaner to clean the fan.
• Other than that, the device does not require maintenance.
The fan operates only for a brief period, then switches off:
• Check whether the protective grid at the air inlet is obstructed in some way. If applicable, remove foreign objects.
• The motor bearing might be damaged. Please contact the customer service.
The fan is not running:
• Check whether the device is switched on.
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
Note
Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.
9 EN
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 11

Technical annex

Technical data

Parameter Value
Model TFV10
Air flow rate
Stage 1
Stage 2 Mains connection 1/N/PE ~230V/ 50Hz/ 0.5A Power input 0.09 kW Stat. air pressure (freely
blowing) Protection type IP22 Sound level (distance 3m)
Stage 1
Stage 2 Dimensions (L x W x H) 250x 310x 270(mm) Weight 5kg
Model TFV20
Air flow rate
Stage 1
Stage 2 Mains connection 1/N/PE ~230V/ 50Hz/
Power input 0.49 kW Stat. air pressure (freely
blowing) Protection type IP22 Sound level (distance 3m)
Stage 1
Stage 2 Dimensions (L x W x H) 343x 335x 355(mm) Weight 12kg
310m³/h 380m³/h
max. 150Pa
61.5 dB(A)
68.5 dB(A)
850 m³/h 1,185 m³/h
2.15A
max. 390Pa
64 dB(A) 69 dB(A)
Parameter Value
Model TFV30
Air flow rate
Stage 1 Stage 2 Stage 3
1,600m³/h 1,850m³/h
2,200m³/h Mains connection 1/N/PE ~230V/ 50Hz/ 5.2A Power input max. 0.85kW Stat. air pressure (freely
max. 425Pa blowing)
Protection type IP22 Sound level (distance 3m)
Stage 1 Stage 2 Stage 3
73.5 dB(A)
80.8 dB(A)
86.2 dB(A) Dimensions (L x W x H) 440x 440x 440(mm) Weight 18.5kg

Disposal

The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. For further return options provided by us please refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling and other forms of recovery of waste equipment as well as to prevent negative effects for the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment.
EN 10
Operating manual – turbo fan TFV 10 / TFV 20 / TFV 30
Page 12
Trotec GmbH & Co. KG
Grebbener Str. 7 D-52525 Heinsberg
+49 2452 962-400 +49 2452 962-200
info@trotec.com www.trotec.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use