Trotec TDS 50 E operation manual

TDS 19 E / TDS 29 E / TDS 50 E

EN

ORIGINAL INSTRUCTIONS

ELECTRIC HEATER

TRT-BA-TDS19E-TDS29E-TDS50E-TC2016-22-004-EN

Table of contents

Notes regarding the instructions ..........................................2

Safety .....................................................................................2

You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:

Information about the device................................................5

Transport and storage...........................................................6

Assembly and installation.....................................................6

Operation ...............................................................................8

Errors and faults....................................................................9

Maintenance ........................................................................10

Technical annex...................................................................11

Disposal ...............................................................................18

Declaration of conformity ...................................................18

Notes regarding the instructions

Symbols

Warning of electrical voltage

This symbol indicates dangers to the life and health of
persons due to electrical voltage.

TDS 19 E

https://hub.trotec.com/?id=39595

TDS 29 E

https://hub.trotec.com/?id=39596

TDS 50 E

https://hub.trotec.com/?id=39597

Safety

Warning of hot surface

This symbol indicates dangers to the life and health of
persons due to hot surface.

Warning

This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.

Caution

This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.

Note

This signal word indicates important information
(e.g. material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry
out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the
instructions must be observed.

Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!

Warning
Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.

Save all warnings and instructions for future
reference.

This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.

2 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Warning

Children of less than 3years should be kept away
unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.

Warning

Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.

• Do not use the device in potentially explosive rooms.

• Do not use the device in aggressive atmosphere.

• Set the device up in an upright and stable position.

• Let the device dry out after a wet clean. Do not operate it
when wet.

• Do not use the device with wet or damp hands.

• Do not expose the device to directly squirting water.

• Never insert any objects or limbs into the device.

• Do not cover or transport the device during operation.

• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.

• Do not sit on the device.

• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.

• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.

• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!

• The electrical connection must correspond to the
specifications in chapter Technical data.

• Insert the mains plug into a properly secured mains
socket.

• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.

• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.

• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!

• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.

• Do not use the device in immediate proximity to curtains.

• Make sure that the air inlet and outlet are not obstructed.

• Do not place the device on combustible ground.

• Allow the device to cool down before transport and/ or
maintenance work.

• Do not use this device near bathtubs, shower trays,
swimming pools or other water containers. Risk of electric
shock!

Intended use

Only use the device for heating closed rooms whilst adhering to
the technical data.
Intended use comprises heating the air in:

– Construction trailers
– Greenhouses
– Boathouses
– Garages
– Market stalls
– Workshops
– Catering trade
– Warehouses and halls
– Shipbuilding

EN 3

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Improper use

• Do not place any objects, e.g. clothing, on the device.

• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.

• The device must not be used near swimming pools.

• Do not use the device outdoors.

• Do not use the device for heating in vehicles.

• Do not use this device in the immediate vicinity of sinks,
bathtubs or other water containers.

Never immerse the device in water.

• Do not place the device on wet or flooded ground.

• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.

• Any unauthorised modifications, such as alterations or
structural changes to the device, are forbidden.

Personnel qualifications

People who use this device must:

• be aware of the dangers that occur when working with
electric devices in damp areas.

• have read and understood the instructions, especially the
Safety chapter.

Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.

Symbols on the device

Symbols Meaning

This symbol located on the device indicates that it
is prohibited to place objects (such as towels,
clothes etc.) above or directly in front of the
device.
In order to avoid overheating and fire hazards, the
heater must not be covered.

Residual risks

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of hot surface

Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!

Warning

Improper handling entails a risk of burning and electric
shock.
Only use the device as intended!

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Warning

Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.

Warning

In order to avoid overheating and fire hazards, the
heater must not be covered.

Behaviour in the event of an emergency

1. Switch off the device.

2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.

3. Do not reconnect a defective device to the mains.

Overheating protection

The device is provided with a safety thermostat which is
activated by overheating of the device (when exceeding the
operating temperature).
Once the safety thermostat has switched itself on, the heating
elements of the devices will be turned off. The fan keeps
running.
Allow the device to cool down and switch it off. Investigate the
cause of overheating. Should the problem persist, please
contact the customer service.

4 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Information about the device

TDS 19E

3 kW

1

2

3

4

5

TDS 29E

5 kW

1

2

3

4

5

Device description

The electric heater serves to generate and distribute warm air,
e.g. in interior spaces.

The device generates heat by means of a heating element. The
air surrounding the heating element is heated. The heated air is
blown into the room by a fan.

The device is equipped with an integrated thermostat and so
generates a constant flow of warm air.

Fan operation without heating function is also possible.

Device depiction

TDS 19 E

TDS 29 E

No. Designation

1 Transport handle

2 Air outlet

3 Rotary control thermostat

4 Air inlet

5 Selection switch for ventilation and heating levels

No. Designation

1 Transport handle

2 Air outlet

3 Rotary control thermostat

4 Air inlet

5 Selection switch for ventilation and heating levels

EN 5

electric heater TDS 19 E / TDS 29 E / TDS 50 E

TDS 50 E

TDS 50E

9 kW

1

2

3

4

5

No. Designation

1 Transport handle

2 Air outlet

3 Rotary control thermostat

4 Air inlet

5 Selection switch for ventilation and heating levels

Transport and storage

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

To make the device easier to transport, it is fitted with a carry
handle.

Before transporting the device, observe the following:

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out
of the mains socket.

• Do not use the power cable to drag the device.

• Allow the device to cool down sufficiently.

Storage

Before storing the device, proceed as follows:

• Hold onto the mains plug while pulling the power cable out
of the mains socket.

• Allow the device to cool down sufficiently.

When the device is not being used, observe the following
storage conditions:

• dry and protected from frost and heat

• in an upright position where it is protected from dust and
direct sunlight

• with a cover to protect it from invasive dust, if necessary

• Place no further devices or objects on top of the device to
prevent it from being damaged.

Assembly and installation

Scope of delivery

• 1 x Electric heater

• 1 x Transport handle

• 2 x Screw

• 2 x Washer

• 1 x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.

6 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Assembly

A

B

C

C

D

Use tools suitable for the intended task.

Mounting the transport handle

Prior to initial start-up, the transport handle must be attached to
the device.

The procedure is identical for all three devices
(TDS 19 E/TDS 29 E/TDS 50 E).

To do so, please proceed as follows:

1. Loosen the two screws and the two washers from the top
of the housing.

Start-up

Info

Odours might arise upon initial start-up or after a
longer period of non-use.

When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.

2. Use the screws and washers to mount the transport
handle.

• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.

• Set the device up in an upright and stable position.

• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are completely unrolled.

• Make sure that no curtains or other objects interfere with
the air flow.

• Make sure that the device cannot come into contact with
moisture or water.

Connecting the power cable

• Insert the mains plug into a properly secured mains
socket.

• Make sure that the power cable is guided along the back
of the device. Never guide the power cable along the front
of the device!

EN 7

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Operation

35

• Avoid open doors and windows.

Control panel

No. Designation

3 Rotary switch room thermostat

5 Selection switch for ventilation and heating levels

0 : The device is switched off.

: ventilation only

: heating level 1

: heating level 2

Switching the device on

Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.

Info

The device will not be switched on until the room
temperature falls below the temperature set at the
room thermostat, except when running in cold setting
(ventilation only). The fan is independent of the
thermostat.

Setting the heating level

1. Set the selection switch(5) to the desired heating level.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

TDS19E

• Turn the room thermostat's rotary switch(3) to the
MINposition.

• Turn the selection switch(5) to the position (ventilation
only).

• Keep the fan running for 3minutes before switching the
device off.

• Switch off the device by setting the selector switch(5) to
position0.

• Hold onto the mains plug while pulling the power cable out
of the mains socket.

• Allow the device to cool down completely.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

TDS29E/ TDS50E

• Turn the room thermostat's rotary switch(3) to the
MINposition.

• Switch off the device by setting the selector switch(5) to
position0.

• The fan keeps running for approx. 3minutes and then
switches off automatically.

• Wait until the fan has completed the rundown operation.

• Hold onto the mains plug while pulling the power cable out
of the mains socket.

• Allow the device to cool down completely.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Setting the room thermostat

1. Select the desired temperature via the stepless rotary
switch(3) of the room thermostat.

The room thermostat controls the room temperature
automatically:

TDS19E

• When exceeding the set value, both the heating and the
ventilation will be switched off.

• When falling below the set value, both the heating and the
ventilation will automatically be switched back on.

TDS29E and 50E

• When the set value is exceeded, the heating switches off.
The fan keeps running until the device is switched off.

• When falling below the set value, the heating automatically
switches back on in addition to the running fan.

8 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Errors and faults

Warning of electrical voltage

Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.

The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• TDS19E: Check the room temperature. The room
thermostat may have switched off, because the desired
room temperature has been reached.

• The motor might be defective. Have a defective motor
replaced by a specialist electrical company.

• The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.

• Check whether the overheating protection has tripped, see
chapter Safety.

• Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.

The air current is reduced:

• Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe the
minimum distance from walls or other objects according to
the technical data.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright
position.

Note

Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.

Your device still does not operate correctly after these
checks?

Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.

The device is switched on, the fan is operating, the heating
is not:

• TDS29E and TDS50E: Check the room temperature. The
room thermostat may have switched off, because the
desired room temperature has been reached.

• Check whether the overheating protection has tripped, see
chapter Safety.

• The heating resistor might have blown. Have a defective
heating resistor replaced by a specialist electrical
company.

• The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.

The fan is not running:

• Check whether the device is switched on.

• Check the power connection.

• Check the power cable and mains plug for damages.

• The fan motor might be defective. Have a defective fan
motor replaced by a specialist electrical company.

EN 9

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Maintenance

Maintenance intervals

Maintenance and care interval before every

start-up

Check air inlets and outlets for dirt

X

and foreign objects and clean
ifnecessary

Clean the exterior

Visually check the inside of the
device for dirt

Check air inlet grid(s) and air

X X

filter(s) for dirt and foreign objects
and clean or replace ifnecessary

Check for damage

X

Check the attachment screws

Test run

Maintenance and care log

Device type: .............................................

Maintenance and care interval

Check air inlets and outlets for dirt
and foreign objects and clean
ifnecessary

Clean the exterior

Visually check the inside of the
device for dirt

Check air inlet grid(s) and air
filter(s) for dirt and foreign objects
and clean or replace ifnecessary

Check for damage

Check the attachment screws

Test run

Remarks:

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

as needed at least every

2weeks

X X

X X

X X

at least every
4weeks

at least every
6months

Device number: ....................................

at least
annually

X

1. Date: ...................................

Signature: ................................

5. Date: ...................................

Signature: ................................

9. Date: ...................................

Signature: ................................

13. Date: .................................

Signature: ................................

10 EN

2. Date: ....................................

Signature: .................................

6. Date: ....................................

Signature: .................................

10. Date: ..................................

Signature: .................................

14. Date: ..................................

Signature: .................................

electric heater TDS 19 E / TDS 29 E / TDS 50 E

3. Date: ....................................

Signature: .................................

7. Date: ....................................

Signature: .................................

11. Date: ..................................

Signature: .................................

15. Date: ..................................

Signature: .................................

4. Date: ....................................

Signature: .................................

8. Date: ....................................

Signature: .................................

12. Date: ..................................

Signature: .................................

16. Date: ..................................

Signature: .................................

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out
of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.

Cleaning the housing

Warning of electrical voltage

Never immerse the device in water!

Clean the housing with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.

Wipe the housing dry after cleaning.

Technical annex

Technical data

Parameter Value

Model TDS 19 E TDS 29 E TDS 50 E

Heating
capacity
level1:
level2:
level3:

Air flow rate 320m3/h 430m3/h 845m3/h

Operating
range

Mains
connection

Max. power
input

Nominal
current
consumption

Fusing 16 A 16 A 16 A

Plug type Schuko plug

Cable length 1.2m 1.2m 1.3m

Sound
pressure level
(atadistance
of1m)

Protection type IPX4 IPX4 IPX4

Overheating
protection

Weight 4kg 6kg 10kg

Dimensions
(lengthx
widthx height)

Minimum
distance to
walls and
other objects

top(A):

rear(B):

sides(C):

front(D):

ventilation only
1500W
3000W

-20°C to
+45°C

ventilation only
2500W
5000W

-20°C to
+45°C

ventilation only
4500W
9000W

-20°C to
+45°C

230V/ 50Hz 400V/ 50Hz 400V/ 50Hz

3000W 5000W 9000W

13A 7.2A 13A

CEE7/7

CEEplug,
5-pin, 16A

CEEplug,
5-pin, 16A

49dB(A) 53dB(A) 55dB(A)

65°C 75°C 65°C

290x210x
320(mm)

50cm
50cm
50cm
50cm

350x240x
360(mm)

50cm
50cm
50cm
50cm

390x300x
430(mm)

50cm
50cm
50cm
50cm

EN 11

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Circuit diagram TDS19E

12 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Circuit diagram TDS29E

EN 13

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Circuit diagram TDS50E

Time-delay thermostat

Motor

1

L1

M

Swi tch

2

L2

Relay

2

4

Heating element

L3

6

8

Self-resetting thermostat

0

1

Adjustable thermostat

E

3

14 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Overview of spare parts and spare parts list TDS19E Note!

The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.

No. Spare part Specifications QTY

1 Handle ABS 1

2 Outer Shell SPCC 1

3 Self-resetting

250V/16A/65°C 1

thermostat

4 Adjustable thermostat 250V/16A/85°C 1

5 Rotary switch 250V/16A 1

6 Mica sheet 0.8mm 1

7 Rear net cover SPCC 1

8 Pressure plate cover ABS 1

9 Pressing plate seat ABS 1

10 Knob PA black 2

EN 15

electric heater TDS 19 E / TDS 29 E / TDS 50 E

No. Spare part Specifications QTY

11 Power cord H07RN-F 3G 1.5 mm21

12 Front grill SPCC 1

13 Heating element AC 220-240V~ 50 Hz

1500 W

14 Inner casing SECC 1

15 Foot pad PA 4

16 Floor SPCC 1

17 Inner casing holder SECC 4

18 Fan Ø 170mm 1

19 Motor 220-240V 50Hz 30W 1

20 Motor protective cover PA black 1

2

Overview of spare parts and spare parts list TDS29E Note!

The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.

No. Spare part Specifications QTY

1 Handle PA 1

2 Outer Shell SPCC 1

3 Re-set thermostat 250V/16A/75°C 1

4 Time delay thermostat 250V/16A/K45 1

5 Self-resetting

SECC 1

thermostat holder

6 Relay 380-400V AC 25A 1

7 Relay holder SECC 1

8 Adjustable thermostat 250V/16A/85°C 1

9 Rotary switch 250V/16A/TUV 1

10 Mica sheet 0.8 mm 1

11 Pressure plate cover ABS 1

12 Pressing plate cover ABS 1

13 Knob PA black 2

14 Power cord H07RN-F 4G 1.5 mm21

16 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

No. Spare part Specifications QTY

15 Industrial plug assembly 240/415V 16A 1

16 Front grill SPCC 1

17 Heating element AC220-240V 50Hz

1650W

18 Under support of heating

SECC 1

element

19 Upper support of heating

SECC 1

element

20 Foot pad PA 4

21 floor SPCC 1

22 Inner casing SECC 1

23 Inner casing holder SECC 4

24 Fan Ø 200mm 1

25 Motor 400V 50Hz 30W 1

26 Rear net cover SPCC 1

3

Overview of spare parts and spare parts list TDS50E Note!

The position numbers of the spare parts differ from those
describing the positions of the components mentioned in these
instructions.

No. Spare part Specifications QTY

1 Handle PA 1

2 Outer Shell SPCC 1

3 Re-set thermostat 250V/16A/65°C 1

4 Time delay thermostat 250V/10A/K45 1

5 Relay 380-400V AC 25A 1

6 Relay holder SECC 1

7 Adjustable thermostat 250V/16A/85°C 1

8 Rotary switch 250V/16A/TUV 1

9 Mica sheet 0.8 mm 2

10 Pressure plate cover ABS 1

11 Pressing plate seat ABS 1

12 Knob PA black 2

13 Power cord H07RN-F 4G 2.5 mm21

No. Spare part Specifications QTY

15 Front grill SPCC 1

16 Heating element AC220-240V 50Hz

3000W

17 Under support of heating

SECC 1

element

18 Upper support of heating

SECC 1

element

19 Foot pad PA 4

20 floor SPCC 1

21 Inner casing SECC 1

22 Inner casing holder SECC 8

23 Fan Ø 250mm 1

24 Motor 400V 50Hz 52W 1

25 Rear net cover SPCC 1

14 Industrial plug assembly 240/415V 16A 1

EN 17

electric heater TDS 19 E / TDS 29 E / TDS 50 E

3

Disposal

The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.

The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Declaration of conformity

The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at https://hub.trotec.com/?id=39595.

Declaration of conformity

In accordance with the ECMachinery Directive 2006/42/EC,

AnnexII, part1, SectionA

Herewith, we– Trotec GmbH&Co.KG– declare that the
machinery designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.

Product model/ product:

Product type:

Year of manufacture as of:

Relevant EU directives:

• 2011/65/EU: 1July 2011

• 2014/30/EU: 29March 2014

Applied harmonised standards:

• EN 55014-1:2006/A1:2009

• EN 55014-1:2006/A2:2011

• EN 60335-1:2012/AC:2014

• EN 60335-2-30:2009/A11:2012

• EN61000-3-2:2014

• EN 61000-3-3:2013

• EN 62233:2008

Applied national standards and technical specifications:

• AfPS GS 2014:01

• EN 55014-2:2015

Manufacturer and name of the authorised representative of
the technical documentation:

Trotec GmbH & Co. KG
Grebbener Straße 7, D-52525 Heinsberg
Phone: [phone]
E-mail: [e-mail]

TDS 19 E, TDS 29 E, TDS 50 E

electric heater

2019

Place and date of issue:
Heinsberg, 27.10.2016

Detlef von der Lieck, Managing Director

18 EN

electric heater TDS 19 E / TDS 29 E / TDS 50 E

Trotec GmbH & Co. KG

Grebbener Str. 7
D-52525 Heinsberg

[phone]
[phone]

[e-mail]
www.trotec.com