TDS 20 R / TDS 30 R / TDS 50 R
EN
ORIGINAL INSTRUCTIONS
ELECTRIC HEATER
TRT-BA-TDS20R-TDS30R-TDS50R-TC2014-15-004-EN
Table of contents
Notes regarding the operating manual................................. 2
Safety .....................................................................................2
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
Information about the device................................................4
Transport and storage...........................................................6
Assembly and installation.....................................................6
Operation ...............................................................................7
Errors and faults....................................................................8
Maintenance ..........................................................................8
Technical annex.....................................................................9
Disposal ...............................................................................10
Declaration of conformity ...................................................10
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
TDS 20 R
https://hub.trotec.com/?id=39781
TDS 30 R
https://hub.trotec.com/?id=39809
TDS 50 R
https://hub.trotec.com/?id=39810
Safety
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
2 EN
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Warning
Children of less than 3years should be kept away
unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Warning
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals).
Never use the device if electric cables or the power
connection are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Do not use the device in immediate proximity to curtains.
• Make sure that the air inlet and outlet are not obstructed.
• Do not place the device on combustible ground.
• Allow the device to cool down before transport and/ or
maintenance work.
• Do not use this device near bathtubs, shower trays,
swimming pools or other water containers. Risk of electric
shock!
Intended use
Only use the device for heating closed rooms whilst adhering to
the technical data.
Intended use comprises heating the air in:
– Construction trailers
– Greenhouses
– Boathouses
– Garages
– Market stalls
– Workshops
– Catering trade
– Warehouses and halls
– Shipbuilding
Improper use
• Do not place any objects, e.g. clothing, on the device.
• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
• The device must not be used near swimming pools.
• Do not use the device outdoors.
• Do not use this device in the immediate vicinity of sinks,
bathtubs or other water containers.
Never immerse the device in water.
• Do not place the device on wet or flooded ground.
EN 3
electric heater TDS 20 R / TDS 30 R / TDS 50 R
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the instructions, especially the
Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates that it
is prohibited to place objects (such as towels,
clothes etc.) above or directly in front of the
device.
In order to avoid overheating and fire hazards, the
heater must not be covered.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.
Warning
In order to avoid overheating and fire hazards, the
heater must not be covered.
Behaviour in the event of an emergency
1. Switch off the device.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Overheating protection
The device is provided with a safety thermostat, which is
activated by overheating of the device. In such an event the
device switches off automatically.
When the safety thermostat is activated, allow the device to cool
down. Only then start to look for the cause of overheating.
Should the problem persist, please contact the customer
service.
Information about the device
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of hot surface
Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!
Warning
Improper handling entails a risk of burning and electric
shock.
Only use the device as intended!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Device description
The electric heater serves to generate and distribute warm air,
e.g. in interior spaces.
The device generates heat by means of a heating element.
The air surrounding the heating element is heated. The heated
air is blown into the room by a fan.
The device is equipped with an integrated thermostat and so
generates a constant flow of warm air.
The devices TDS 30 R and TDS 50 R are equipped with a timedelay thermostat. It automatically regulates the device's
rundown operation.
Fan operation without heating function is also possible.
4 EN
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Device depiction
kW
TDS 20 R
TDS 20 R
3 kW
1
2
3
4
TDS 20 R
5
kW
TDS 30 R
TDS 30 R
5 kW
1
2
3
4
TDS 30 R
5
kW
TDS 50 R
TDS 50 R
9 kW
1
2
3
4
TDS 50 R
5
TDS 20 R
TDS 50 R
TDS 30 R
No. Designation
1 Transport handle
EN 5
electric heater TDS 20 R / TDS 30 R / TDS 50 R
2 Selection switch for ventilation and heating levels
3 Rotary control thermostat
4 Air outlet
5 Air inlet
Transport and storage
A
B
C
C
D
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry
handle.
Before transporting the device, observe the following:
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Do not use the power cable to drag the device.
• Allow the device to cool down sufficiently.
Storage
Before storing the device, proceed as follows:
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down sufficiently.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust if necessary
• Place no further devices or objects on top of the device to
prevent it from being damaged.
Assembly and installation
Scope of delivery
• 1 x Electric heater
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Start-up
Info
Odours might arise upon initial start-up or after a
longer period of non-use.
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Set the device up in an upright and stable position.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• Make sure that no curtains or other objects interfere with
the air flow.
• Make sure that the device cannot come into contact with
moisture or water.
Connecting the power cable
• Insert the mains plug into a properly secured mains
socket.
• Make sure that the power cable is guided along the back
of the device. Never guide the power cable along the front
of the device!
6 EN
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Operation
kW
TDS 20 R
3 kW
67
TDS 30 R
5 kW
kW
67
TDS 50 R
9 kW
kW
67
• Avoid open doors and windows.
Control panel
TDS 20 R
TDS 30 R
TDS 50 R
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
Setting the heating level
1. Set the selection switch(6) to the desired heating level.
Setting the room thermostat
1. Select the desired temperature via the stepless rotary
switch(7) of the room thermostat.
The room thermostat controls the room temperature
automatically:
TDS20R
• When exceeding the set value, both the heating and the
ventilation will be switched off.
TDS30R/ TDS50R
• When the set value is exceeded, the heating switches off
while the fan keeps running until the heater has cooled
down sufficiently. As soon as the heater has cooled down
sufficiently, the heater will be switched back on.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Turn the selection switch(6) to ventilation mode .
• Keep the fan running for 3minutes before switching the
device off.
• Switch off the device by setting the selector switch(6) to
position0.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down completely.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
No. Designation
6 Selection switch for ventilation and heating levels
0: The device is switched off.
: ventilation only
: heating level 1
: heating level 2
7 Rotary switch room thermostat
EN 7
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Errors and faults
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• The motor might be defective. Have a defective motor
replaced by a specialist electrical company.
• The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.
• Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is switched on, the fan is operating, the heating
is not:
• Check the room temperature. The room thermostat may
have switched off, because the desired room temperature
has been reached.
• Check whether the overheating protection has tripped, see
chapter Safety.
• The heating resistor might have blown. Have a defective
heating resistor replaced by a specialist electrical
company.
• The room thermostat might be defective. Have a defective
room thermostat replaced by a specialist electrical
company.
The fan is not running:
• Check whether the device is switched on.
• Check the power connection.
• Check the power cable and mains plug for damages.
• The fan motor might be defective. Have a defective fan
motor replaced by a specialist electrical company.
The device is loud or vibrates:
• Check whether the device is set up in a stable and upright
position.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Warning of electrical voltage
Never immerse the device in water!
Clean the housing with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
The air current is reduced:
• Check the air inlet and outlet. Make sure that air inlet and
outlet are not obstructed. Remove any dirt. Observe the
minimum distance from walls or other objects according to
the technical data.
8 EN
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Technical annex
Technical data
Parameter Value
Model TDS 20 R TDS 30 R TDS 50 R
Heating capacity
stage 1:
stage 2:
stage 3:
ventilation only
1500W
3000W
ventilation only
2500W
5000W
ventilation only
4500W
9000W
Air volume 411m3/h 580m3/h 844m3/h
Operating range -20°C to +45°C -20°C to +45°C -20°C to +45°C
Mains connection 1/N/PE~230V / 50 Hz 3/N/PE~400V/ 50Hz 3/PE~400V/ 50Hz
Max. power input 3000W 5000W 9000W
Nominal current
13.04 A 7.22 A 13 A
consumption
Fusing 16 A 16 A 16 A
Plug type CEE 7/7 CEE 16A, 5-pin CEE 16A, 5-pin
Cable length 1.37 m 1.20 m 1.20 m
Sound pressure level
53dB(A) 56dB(A) 56dB(A)
(at a distance of 1m)
Weight 3 kg 5 kg 6.5 kg
Dimensions (lengthx
widthx height) 210x 195x 270(mm) 275x 220x 330(mm) 315x 250x 370(mm)
Minimum distance to walls
and other objects
top(A):
rear(B):
sides(C):
front(D):
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
50cm
EN 9
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Declaration of conformity
The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at https://hub.trotec.com/?id=39781.
Declaration of conformity
In accordance with the ECMachinery Directive 2006/42/EC, AnnexII, part1,
SectionA
Herewith, we– Trotec GmbH&Co.KG– declare that the
machinery designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.
Product model/ product:
Product type:
Year of manufacture as of:
Relevant EU directives:
• 2011/65/EU: 1July 2011
• 2014/30/EU: 29March 2014
Applied harmonised standards:
• EN 55014-1:2006+A1:2009+A2:2011
• EN 55014-2:2015
• EN 60335-2-30:2009/A11:2012
• EN61000-3-2:2014
• EN 61000-3-3:2013
• EN 62233:2008
Applied national standards and technical specifications:
• None
TDS 20 R, TDS 30 R, TDS 50 R
electric heater
2018
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH & Co. KG
Grebbener Straße 7, D-52525 Heinsberg
Phone: +49 2452 962-400
E-mail: info@trotec.de
Place and date of issue:
Heinsberg, 12.08.2018
Detlef von der Lieck, Managing Director
10 EN
electric heater TDS 20 R / TDS 30 R / TDS 50 R
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
Loading...