The current version of the operating manual can be
found at: www.trotec.de
Technical data
ParametersValues
ModelTDS 20
Power input1.65 / 3.3 kW
Current consumption14.35 A
Input voltage230 V / 50 Hz
Amount of air
Setting range0-40 °C
Dimensions410 x 260 x 250 mm
Weight5.3 kg
333.2 m
3
/h
ENOperating Manual – Electrical Fan Heater TDS 201
Page 3
Safety
Read this manual carefully before starting or
using the device. Store the manual near the device
or its site of use!
Intended use
Only use the device TDS 20 to heat enclosed spaces
such as storage facilities, salesrooms, flats as well as
to heat humid or wet surroundings, e.g. on building
sites, whilst adhering to the technical data.
Danger!
Improper use of the heating device can
result in severe injuries due to burns,
fire hazard or electric shocks.
• Ensure a minimum distance of 50 cm to combustible substances. Do not use the device in rooms
where fuel, solvents, varnishes or other easily inflammable vapours are stored. Do not use the device in immediate proximity to curtains.
• Keep away from children and animals.
• Only connect the device to the mains, if voltage
and frequency correspond to the values given on
the nameplate.
• Only use three-wire extension cables with an adequate cross-section.
• Disconnect the device from the mains, if it is not in
use.
• Do not place the device directly underneath a window or electric socket.
• If the device is stored in an unsafe location, make
sure, that it cannot be operated and the power
supply is disconnected at all times.
• Do not use this heating device in immediate proximity to sinks, bathtubs, showers or swimming
pools.
• Unplug the device from the mains before starting
with maintenance, service or repair work.
• Never cover the device with anything, otherwise it
could overheat.
The device conforms to the norms
• EN 60335-1:2002+A11, A1:04+A12, A2:06
• EN 60335-2-30:2003+A1:04+A2:07
• EN 50366:2003+A1:06
and the low-voltage directive 2006/95/EC.
Packaging
• Remove all packing materials which serve to protect the device during transport.
• Extract all individual parts from the box.
• Should the heating device be damaged, please
contact the retailer, where the purchase was
made.
2Operating Manual – Electrical Fan Heater TDS 20EN
Page 4
Operation
1. Fan only2. Minimum3. Maximum
Warning!
Read and observe the warnings and
instructions in the Safety chapter.
Abide by it to ensure a safe operation
of this heating device.
Manual unlocking
The device is provided with a safety thermostat, which
is activated by overheating of the device. When the
safety thermostat is activated, allow the device to cool
down. Only then start to look for a cause of the overheating. Should the problem continue to exist, please
contact the customer service.
Check that the power supply cable is intact. If the
power supply cable is damaged, it must be replaced
by the manufacturer, his customer service or similarly
qualified personnel. Make sure that the electrical
properties of the socket correspond to the values
specified in the operating manual or on the nameplate. Place the device on even ground.
Switch-on of the device
Connect the power supply cable with the mains and
turn the switch into the desired position:
Switch-off
Keep the fan running for 3 minutes, before switching
the device off. Turn the switch into position 0.
Regulation of the room thermostat
Adjust the room temperature by turning
the rotary switch of the room thermostat.
When the set value is exceeded, the
heating resistors switch off while the fan keeps running.
Storage and regular checks
• If you have do not use the device for extended periods of time, thoroughly clean it before putting it
away.
• Store it in a dry location and protect it against dust.
• Before restarting the device, check the condition of
the power cable. If there are doubts as to the
sound condition, contact the customer service.
• Have the device checked once a year at any rate.
Only expert staff trained and authorized by the
manufacturer may carry out maintenance activities on the device.
ENOperating Manual – Electrical Fan Heater TDS 203
Page 5
Errors and faults
Disposal
FaultCauseRemedy
The device works,
but does not heat.
The device does not
switch on.
The air current is
reduced.
The heating resistor
has blown.
Room thermostat is
defective.
Motor is defective.Have it replaced.
Connections are
interrupted.
Air inlet is blocked.Clean air inlet and
Fan motor is defective.
Have it replaced.
Have it replaced.
Unplug and check
connections.
remove obstruction.
Have it replaced.
In the European Union, electronic equipment must not be treated as domestic
waste, but must be disposed of profes-
sionally in accordance with Directive
2002/96/EC of the European Parliament and Council
of 27th January 2003 concerning old electrical and
electronic equipment. At the end of its life, please dispose of this instrument in a manner appropriate to the
relevant legal requirements.
4Operating Manual – Electrical Fan Heater TDS 20EN
Page 6
TROTEC® GmbH & Co. KG • Grebbener Straße 7 • D-52525 Heinsberg
Tel.: +49 2452 962-400 • Fax: +49 2452 962-200
www.trotec.com • E-Mail: info@trotec.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.