Trotec PTNS 10-3, 6V Original Instructions Manual

PTNS 10-3,6V

EN

ORIGINAL INSTRUCTIONS

CORDLESS TACKER

TRT-BA-PTNS10-3,6V-TC-002-EN

Table of contents

Notes regarding the operating manual................................. 1

Follow the manual

Information marked with this symbol indicates that the
operating manual must be observed.

Safety .....................................................................................2

Information about the device................................................6

Transport and storage...........................................................8

Start-up..................................................................................9

Operation .............................................................................11

Errors and faults..................................................................12

Maintenance ........................................................................13

Disposal ...............................................................................14

Declaration of conformity ...................................................14

Notes regarding the operating manual

Symbols

Warning of electrical voltage

This symbol indicates dangers to the life and health of
persons due to electrical voltage.

Wear hearing protection

Information marked with this symbol indicates that you
should wear hearing protection.

Wear safety glasses

Information marked with this symbol indicates that you
should wear eye protection.

Wear protective gloves

Information marked with this symbol indicates that you
should wear protective gloves.

You can download the current version of the operating manual
and the EU declaration of conformity via the following link:

PTNS 10-3,6V

http://hub.trotec.com/?id=41135

Warning of explosive substances

This symbol indicates dangers to the life and health of
persons due to potentially explosive substances.

Warning of sharp object

This symbol indicates dangers to the life and health of
persons due to pointed objects.

Warning

This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.

Caution

This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.

Note

This signal word indicates important information (e.g.
material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry
out your tasks quickly and safely.

1 EN

Operating manual – cordless tacker PTNS 10-3,6V

Safety

Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!

Warning
Observe all the safety warnings, instructions,

illustrations and technical data provided with this
power tool.

Failure to follow the instructions below may result in
electric shock, fire and/ or serious injury.

Save all warnings and instructions for future
reference.

The term power tool used in the safety warnings refers to both
mains-operated and battery-powered electric tools (with/
without power cable).

General Power Tool Safety Warnings – Work area
safety

• If operating a power tool in a damp location is

unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of

electric shock.

General Power Tool Safety Warnings – Personal
safety

• Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal
injury.

Use personal protective equipment. Always
wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.

• Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

General Power Tool Safety Warnings – Electrical
safety

• Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is
earthed or grounded.

• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.

• Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep the cord
away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric
shock.

• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.

• Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.

• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.

• Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are
connected and properly used. The use of a dust

extraction system may reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool
safety principles. A careless action can cause severe

injury within a fraction of a second.

EN 2

Operating manual – cordless tacker PTNS 10-3,6V

General Power Tool Safety Warnings – Power tool
use and care

• Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and / or

the battery pack, if detachable, from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool
accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories carefully. Check

for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

• Keep handles and gripping surfaces dry, clean and
free from oil and grease. Slippery handles and gripping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.

General Power Tool Safety Warnings – Battery tool
use and care

• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with
another battery pack.

• Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.

• When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from

the battery. Avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

• Do not use a damaged or modified battery. Damaged or
modified batteries can behave unexpectedly and lead to
fires, explosions or injuries.

• Do not expose a battery to fire or excessively high
temperatures. Exposure to fire or temperatures above
130°C (265°F) may cause an explosion.

• Follow all the instructions for charging and never

charge the battery or the cordless tool outside the
temperature range specified in the operating
instructions. Incorrect charging or charging outside of the

permissible temperature range can destroy the battery and
increase the risk of fire.

General Power Tool Safety Warnings – Service

• Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety instructions for tackers

• Always assume that the power tool contains fasteners
(wire nails or staples). Careless handling of the tacker

can result in an unexpected ejection of wire nails or
staples and lead to personal injury.

• Do not point the power tool towards yourself or anyone
nearby. Unexpected triggering will eject a wire nail or
staple which might cause an injury.

• Do not actuate the power tool until it is placed firmly
against the workpiece. If the power tool is not in contact
with the workpiece, the staple or wire nail might ricochet.

• Disconnect the power tool from the mains connection

or battery when a wire nail or staple is jammed inside.

If not de-energized, the tacker could be actuated by
accident while removing a jammed staple or wire nail.

• Exercise particular caution when removing a jammed
wire nail or staple. The mechanism may be under tension
and the staple or wire nail could be forcefully ejected while
you attempt to eliminate the jam.

3 EN

Operating manual – cordless tacker PTNS 10-3,6V

• Do not use this tacker for fastening electrical lines. It is
not suitable for the installation of electrical lines, it could
damage the insulation of electric cables thereby causing
electric shock and fire hazards.

• Use appropriate detection equipment to track down

concealed supply lines or consult the local utility
companies. Contact with electrical lines may result in fire

and electric shock. Damaging a gas line may lead to an
explosion. Penetrating a water line causes property
damage and may cause an electric shock.

• Do not under any circumstances use the power tool if

you detect damages on the mains plug or power cable.

If the supply cord is damaged, it must be replaced by the
manufacturer, his service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!

• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.

Intended use

Only use the device PTNS 10-3,6V for tacking cardboard,
leather, insulating material, fabrics made of textile or natural
fibres, foils and similar materials onto a soft ground such as
softwood or material similar to wood whilst adhering to the
technical data.

We recommend using the power tool with original Trotec
accessories.

Improper use

The device PTNS 10-3,6V is not suitable for tacking hard
materials such as metals, stone materials, glass and hard
plastics.

Personnel qualifications

People who use this device must:

• have read and understood the operating manual, especially
the Safety chapter.

Personal protective equipment

Wear hearing protection.

Excessive noise can lead to hearing loss.

Wear eye protection.

With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.

Wear protective gloves.

They protect your hands from burns, crushing injuries
and skin abrasions.

Residual risks

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
of the charger from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning of explosive substances

Do not expose the battery to temperatures above
45 °C! Do not let the battery come into contact with
water or fire! Avoid direct sunlight and moisture. There
is a risk of explosion!

Warning

Make sure not to hit power, gas or water lines when
working with a power tool.
If necessary, use a pipe detector to check the wall you
want to drill in or slit open.

Warning

Risk of injuries caused by flying parts or bursting tool
heads.

EN 4

Operating manual – cordless tacker PTNS 10-3,6V

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Caution

Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.

Caution

Keep a sufficient distance from heat sources.

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

5 EN

Operating manual – cordless tacker PTNS 10-3,6V

Information about the device

8

1

7
6

3

2

4

5

9

10

11

Device description

The PTNS 10-3,6V is a cordless tacker designed for tacking
insulating material or decoration.

You can staple and tack cardboard, leather, textile or natural
fibres and similar materials onto softwood or material similar to
wood.

A shot sequence of 30shots per minute can be accomplished.
The device comes with a magazine filling level indication for

checking the remaining supply of staples and wire nails. The
magazine can accommodate up to 100staples of type53 or
50wire nails of type47.

Device depiction

No. Designation

1 Magazine release
2 Trigger
3 Magazine filling level indicator
4 Tacker guide nose/ staple ejection
5 Magazine slider
6 On/off switch
7 MicroUSB charging socket
8 Battery level indication
9 Charger
10 Wire nails
11 Staples

EN 6

Operating manual – cordless tacker PTNS 10-3,6V

Scope of delivery

• 1x Device PTNS 10-3,6V

• 1000 x Staple, type53, length:6mm, width: 11.4mm

• 1000 x Staple, type53, length:8mm, width: 11.4mm

• 500 x Wire nail, type47, length:10mm, width: 1.8mm

• 1 x Quick charger

• 1x Manual

Technical data

Parameter Value

Model PTNS10-3.6V

Nominal voltage 3.6 V
Impact frequency 30spm
Fastener type: staple

Type

53

Length

Thickness

Fastener type: wire nail

Length

Max. holding capacity of magazine 100 staples, 50 wire nails
Weight 0.7 kg

Battery (integrated)

Type Li-ion
Nominal voltage 3.6 V
Capacity 1.5Ah

Width

Type

Width

4 – 10mm

11.4mm

0.74 mm

47
10 mm

1.8 mm

Charger PTNS10-3.6VAC

Nominal voltage input 100 – 240V / 50 – 60Hz
Nominal current input 0.2 A
Nominal voltage output 5 V
Charging current output 600 mA
Charging time 3 h
Protection class

II /

Vibration information according
to EN60745

Vibration emission value a

h

11.6 m/s²

Uncertainty K 1.5 m/s²

Sound values according to
EN60745

Sound pressure level L
Sound power L

WA

pA

80 dB(A)
91 dB(A)

Uncertainty K 3 dB

Wear hearing protection.

Excessive noise can lead to hearing loss.

7 EN

Operating manual – cordless tacker PTNS 10-3,6V

Information on noise and vibration:

• The vibration level specified in these instructions was
determined by means of a measuring method standardized
in EN60745 and can be used for a device comparison. The
specified vibration emission value may also be used for a
preliminary assessment of the exposure.

Caution

Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.

• The vibration level will change depending on the
application of the power tool and may in some cases differ
from the value specified in these instructions. The vibration
load may be underestimated if the power tool is used
regularly in such a way. For a precise estimation of the
vibration load during a certain work period, it is also
important to consider the periods during which the device
is switched off, or is running but not actually employed.
This can reduce the vibration load over the entire work
period significantly.

Transport and storage

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

• Allow the device to cool down.

The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.

Observe the following when transporting or shipping Li-ion
batteries:

• The user may transport the batteries by road without any
additional requirements.

• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.

– Only ship batteries if their housing is undamaged.
– Please also observe any other national regulations.

Storage

Before storing the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

• Allow the device to cool down.

• Clean the device as described in the Maintenance chapter.

• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.

When the device is not being used, observe the following
storage conditions:

• dry and protected from frost and heat

• ambient temperature below 40 °C

• protected from dust and direct sunlight

EN 8

Operating manual – cordless tacker PTNS 10-3,6V

Start-up

9

7

Unpacking the device

• Take the device and the accessories out of the packaging.

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

• Check the scope of delivery for completeness and look for
damages.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

• Dispose of the packaging material according to the
national regulations.

Charging the battery

Caution

While the battery is charging, the handle may become
slightly warm. This is normal.

Note

The battery can be damaged in case of improper
charging.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.

The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.

The battery should be charged prior to initial start-up and when
the battery is low (the battery level indication(8) is illuminated
in red). To do so, please proceed as follows:

ü The device is switched off.

1. Plug one end of the charger(9) into the microUSB
charging socket(7) at the device.

2. Insert the mains plug of the charger(9) into a properly
fused mains socket.

ð The battery level indication is illuminated in red.
ð Charging requires approx. 3hours.

3. Wait until the light of the battery level indication turns
green.

ð The batteryis fully charged.

4. Pull the mains plug of the charger(9) out of the mains
socket.

5. Unplug the charger(9) from the microUSB charging
socket(7) at the device.

ð The device and the charger may have become warm

during charging.

Info

The device cannot be started when the charger is
connected. It is possible to pull the trigger, but the
motor will not start.

Checking the battery charging status

The charging status is displayed by the battery level indication
as follows:

LED colour Meaning

Green The battery is fully charged.
Red The battery is currently charging.

9 EN

Operating manual – cordless tacker PTNS 10-3,6V

Filling the magazine

1

5

11

12

10

13

12

Warning of electrical voltage

Before any work on the device, remove the mains plug
of the charger from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning

Make sure that the device is switched off.
Make sure not to hold the device by the trigger when a
staple or wire nail is jammed inside!
The trigger could be actuated by accident while
removing a jammed staple or wire nail.

Wear safety glasses

Wear appropriate eye protection when working with
the device.

Info

At the magazine filling level indicator you can check
whether any staples or wire nails are left in the
magazine.

Info

Do not open or close the magazine by force (e.g. for
filling).

ü The device is switched off. The on/off switch(6) is set to

position0.

1. Turn the bottom of the device up.

2. Squeeze the magazine release(1) together and pull the
magazine slider(5) out towards the back.

3. Insert the staples(11) in the magazine(12) with their tips
pointing up.

4. Alternatively, that magazine(12) can also be filled with
wire nails(10). Observe the mark(13) on the left-hand side
of the magazine slider that indicates the guiding groove for
the wire nails. Insert the wire nails in the magazine with
their heads pointing downwards.

Note

Wire nails can only be inserted as depicted: on the left­hand side of the magazine.

EN 10

Operating manual – cordless tacker PTNS 10-3,6V

5. Slide the magazine slider(5) back down alongside the

5

12

6

magazine(12) until it clicks into place.

Operation

Tips and notes on handling the tacker

Warning of sharp object

Wire nails and staples are sharp. Risk of injuries if
handled without due care!

General information:

• Always apply the device to the workpiece firmly and at a
right angle. Otherwise the staple or wire nail could be
diverted sideways.

• Be careful when using the device on soft workpieces. Else
the workpiece could be damaged.

• Observe the size of staples and wire nails as specified in
the technical data.

• At the magazine filling level indicator you can check
whether any staples or wire nails are left in the magazine.

• Make sure not to hold the device by the trigger when a
staple or wire nail is jammed inside! The trigger could be
actuated by accident while removing a jammed staple or
wire nail.

• The movable tacker guide nose also serves as safety
catch. It makes sure that a shot cannot be released
accidentally just by inadvertently pulling the trigger.

Switching the device on and off

Wear your personal protective equipment when working with
the device.

1. Set the on/off switch(6) to I to switch the device on.

11 EN

Operating manual – cordless tacker PTNS 10-3,6V

2. Put the tacker guide nose(4) down on the respective spot

2

4

6

you want to tack. The tacker guide nose must be pushed in
by a few millimetres.

3. Pull the trigger(2).

ð The wire nail or staple is injected into the workpiece.

4. Having driven the staple or wire nail in all the way, release
the trigger and withdraw the tacker guide nose from the
workpiece.

5. Set the on/off switch(6) to 0 to switch the device off.

Errors and faults

The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.

Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.

Slight smoke or odour are emitted during first use:

• This is not a fault. These phenomena disappear after a
brief runtime.

The device does not start:

• The battery power might be too low. Recharge the battery.

• Check the charger and charging socket for dirt. Remove
any dirt.

• Check whether the charger is connected. If the charger is
connected, the device will not start.

Info

Wait for at least 10 minutes before switching the
device back on.

The battery does not charge:

• Check whether the device is correctly connected to the
charger and whether the charger is correctly connected to
the power supply.

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the fuse (home).

• Check the charger for damages. Should the charger be
damaged, stop using it. Contact the Trotec customer
service.

• Check the charger connection for dirt. Remove any dirt.

• The battery might be defective. Contact the Trotec
customer service.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

EN 12

A wire nail or staple is jammed in the device:

Warning

Ensure that the device is switched off.
Make sure not to hold the device by the trigger when a
staple or wire nail is jammed inside!
The trigger could be actuated by accident while
removing a jammed staple or wire nail.

• Open the magazine release and remove the wire nail or
staple.

Operating manual – cordless tacker PTNS 10-3,6V

The device becomes hot:

• Make sure not to exert too much pressure on the device
during operation.

• Keep the venting slots clear to prevent the motor from
overheating.

• Wait for at least 10 minutes before switching the device
back on.

Note

Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.

Your device still does not operate correctly after these
checks?

Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug of the charger with wet or
damp hands.

• Switch the device off.

• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.

Notes on maintenance

Inside the device, there are no parts that need to be maintained
or lubricated by the user.

Cleaning

The device should be cleaned before and after each use.

Note

The device does not have to be lubricated after
cleaning.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

• Clean the device with a soft, damp and lint-free cloth.
Ensure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.

• Dry the device with a soft, lint-free cloth.

• Keep the connecting terminals on the device and charger
clean.

• Keep the ventilation openings free from dust deposits to
prevent overheating of the motor.

13 EN

Operating manual – cordless tacker PTNS 10-3,6V

Disposal

Li-Ion

The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.

The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Declaration of conformity

The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at http://hub.trotec.com/?id=41135.

Declaration of conformity

In accordance with the EC Machinery Directive 2006/42/EC, AnnexII, part1,

SectionA

Herewith, we – Trotec GmbH & Co. KG – declare that the
machinery designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.

Product model/ Product:

Product type:

Year of manufacture as of:

Relevant EU directives:

• 2011/65/EU: 1July 2011

• 2014/30/EU: 29March 2014

Applied harmonised standards:

• EN ISO 12100:2010

• EN 55014-1:2006+A1+A2

• EN 55014-2:2015

• EN 60745-1:2009+A11: 2010

• EN60745-2-16:2010

Applied national standards and technical specifications:

• None

PTNS 10-3,6V

cordless tacker

2017

Manufacturer and name of the authorised representative of
the technical documentation:

Trotec GmbH & Co. KG
Grebbener Straße 7, D-52525 Heinsberg
Phone: [phone]
E-mail: [e-mail]

Place and date of issue:
Heinsberg, 22.10.2017

Detlef von der Lieck, Managing Director

EN 14

Operating manual – cordless tacker PTNS 10-3,6V

Trotec GmbH & Co. KG

Grebbener Str. 7
D-52525 Heinsberg

[phone]
[phone]

[e-mail]
www.trotec.com