IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
EN
OPERATING MANUAL
INFRARED RADIANT HEATER
TRT-BA-IRD1200-IRD1800-IRD2400-IRD3200-TC-001-EN
Table of contents
Notes regarding the operating manual................................. 1
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................5
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
Assembly and installation.....................................................5
Operation ...............................................................................9
Errors and faults..................................................................11
Maintenance ........................................................................12
Technical annex...................................................................13
Disposal ...............................................................................13
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
IRD 1200
https://hub.trotec.com/?id=41386
IRD 1800
https://hub.trotec.com/?id=41387
IRD 2400
https://hub.trotec.com/?id=41388
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Notice
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
IRD 3200
https://hub.trotec.com/?id=41389
1 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Warning
Children of less than 3years should be kept away
unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Warning
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk.
• During the installation of the device observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Do not use the device in immediate proximity to curtains.
• Do not transport the device during operation.
• Allow the device to cool down before transport and/ or
maintenance work.
• The device must not be installed directly beneath a wall
socket.
• The device must be set up in a way that the switches and
controllers cannot be touched by a person in a bathtub or
shower.
EN 2
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Intended use
Only use the device IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
for heating surfaces in interior spaces, in roofed and non-roofed
outdoor areas.
Intended use comprises:
• Heating surfaces
– in living spaces,
– in storage facilities,
– in salesrooms,
– in construction areas,
– in containers,
– in the catering trade,
– at trade fairs and events,
– in outdoor areas (e.g. terraces).
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of hot surface
Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!
Improper use
The device is not intended for industrial use.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device for heating in vehicles.
• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
• The device may not be used as a heating device for
babies / children or animals.
• The device may not be installed inside a shower or directly
above a bathtub.
• The device must not be used near swimming pools.
• Do not use this device in the immediate vicinity of sinks,
bathtubs or other water containers.
Never immerse the device in water.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Risk of injury due to infrared radiation!
Do not stay in the device's immediate vicinity for too
long. Do not look directly into the device for too long.
Observe the minimum distances.
Warning
Improper installation or mounting entails a risk of fire.
Warning
In order to avoid overheating and fire hazards, the
heater must not be covered.
Behaviour in the event of an emergency
1. Switch the device off.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
3 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Information about the device
1
2
5
3
TIMERP3
P2P1
4
Device description
The infrared radiant heater (blacklight) IRD 1200 / IRD 1800 /
IRD 2400 / IRD 3200 serves to quickly generate heat without
emitting light.
The device is based on the functional principle of heat
generation by infrared radiation. Persons or objects are heated
directly.
Via a stainless steel heating coil enclosed in aluminium, the
device emits most of its radiation energy in the long-wave
infrared spectrum. The device does not generate any dazzling
red light during operation. In addition, this type of heat
generation is also energy-saving. The full heating capacity is
only reached after approx.10min of operation. This is why the
device is classified as slow-acting with regard to its operating
principle.
The maximum effective range is approx.2.7metres. Wind and
draught, however, can reduce this effective range. For this
reason, it is recommended to use the device in interior spaces
or outdoor areas sheltered from the wind.
The 3heating levels can be selected using the remote control.
The device indicates operation by means of two-coloured LEDs.
Using the timer function the device can be switched off
automatically with time delay.
• suitable for interior spaces and outdoor use in areas
sheltered from the wind
• IP55 type of protection – splash- and water-jet-proof
• suitable for mounting on walls and ceilings
• adjustable angle
• no dust circulation (suitable for allergy sufferers)
Device depiction
No. Designation
1 Display with infrared receiver for remote control
2 On/off switch
3 Guide rail for device holder
4 Remote control
5 Aluminium cover
EN 4
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Transport and storage
TIMERP3
P2P1
6
7
8
9
10
11
12
13
4
14
15
161718
Assembly and installation
Notice
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Do not use the power cable to drag the device.
• Allow the device to cool down sufficiently.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust if necessary
• Remove batteries from the remote control.
Scope of delivery
• 1x Device (not pictured)
• 4x Mounting bracket(6)
• 2 x Device holder(7)
• 4 x Hexagon nut M8(8)
• 4 x Spring washer Ø 8.1 mm(9)
• 4 x Washer Ø 8.4 mm(10)
• 4 x Threaded steel anchor M8(11)
• 2 x Wing screw M6(12)
• 4 x Hexagon screw M6(13)
• 4 x Spring washer Ø 6.1 mm(14)
• 4 x Hexagon nut M6(15)
• 4 x Spring washer Ø 4.1mm(16)
• 4 x Hexagon nut M4(17)
• 4 x Phillips screw M4(18)
• 1 x Remote control(4)
• 1xManual (not pictured)
5 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
The device is suited for wall and ceiling mounting. Observe the
following requirement for installation inside a room:
Warning
Risk of fire due to improper installation!
There is a risk of fire if the required minimum
distances are not observed.
The device must be positioned at a distance of at least
220 cm from the floor and at least 100 cm from walls
and other objects such as curtains or sockets.
Mounting the wall/ceiling holder
Info
The mounting procedure is identical for all devices.
ü Use tools suitable for the intended task.
1. Connect one device holder and one mounting bracket each
using two medium hexagon screws(M6), hexagon
nuts(M6) and spring washers(Ø6.1mm).
3. Push the two device holders into the guide rails one after
the other. Pay attention not to push the device holders
over the power cable when inserting them in the guide rail.
4. The brackets' position can be freely adjusted. The
recommended distances are provided in the table below:
2. Connect the second device holder to the second mounting
bracket.
Holder
IRD 1200 IRD 1800 IRD 2400 IRD 3200
distance
Minimum 400 mm 600 mm 800 mm 1100 mm
Maximum 930 mm 1195 mm 1460 mm 1815 mm
5. Tighten the two wing screws on the device to lock the
device holders.
EN 6
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Installation
220 cm
30 cm
20 cm
20 cm
100 cm
When installing the device, observe the minimum distances
from walls and other objects as described in the Technical data
chapter.
• Minimum distance of 220cm and maximum distance of
270cm from the floor.
• Minimum distance of 100 cm to the front or from objects.
• Minimum distance of 30 cm from the ceiling in case of
wall mounting or, for technical reasons, 19.5cm in case of
ceiling mounting.
• Minimum distance of 20 cm to the sides.
• For installation in bathrooms or washing rooms, observe
the national regulations on safety distances.
• Do not install the device directly in front of a wall socket.
The socket should be located next to the device. If the
device is installed on a pitched ceiling, the socket should
be located at the bottom side of the device.
• Do not install the device directly behind a door.
• Never install the device in a way that it radiates directly
onto walls or other objects.
• Only install the device in a horizontal position.
• Please note that the minimum distance to the front also
applies to objects mounted on the ceiling, e.g. fans, lamps
or sprinkler systems.
Info
Please note that in case of ceiling mounting the
distance from the ceiling is 19.5cm due to the length
of the mounting brackets.
For wall mounting, the minimum distance of 30cm
from the ceiling applies.
The following is required for installation:
• a pencil for marking the drill holes
• a suitable drill
• wall plugs appropriate for the structure of the wall and for
the device weight
• a screwdriver
• a spirit level
Notice
Always install the device with the help of other
persons.
1. Measure the distance between the holders on the device
and use this value for the distance between the drill holes.
2. Mark the drill holes on the wall / ceiling. Please note the
mounting brackets must be fastened vertically.
7 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
3. Drill the holes into the wall / ceiling at the marked
0°
30°
45°
15°
positions.
7. The device can be installed at an inclination angle of 0°,
15°, 30° or 45 °.
Please note that the inclination angle must be 15°, 30° or
45° for wall mounting and 0°, 15° or 30° for ceiling
mounting.
4. Insert suitable wall plugs into the drill holes.
5. Screw the mounting brackets to the wall / ceiling.
6. Check the mounting brackets for tight fit.
8. Connect the mounting brackets on the device to those on
the wall/ ceiling at the desired inclination angle. For each
side, use two Phillips screws, two small hexagon nuts(M4)
and spring washers(Ø4.1mm).
9. Make sure that the device is attached securely.
EN 8
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Effective range
a
b
c
d
20
21
19
The device heats objects and persons inside a certain effective
range. This effective range differs depending on whether the
device is installed indoors or outdoors. In outdoor areas, the
effective range is influenced by the weather and may be
reduced.
a Height b Depth
c Width d Effective range
IRD 1200 IRD 1800 IRD 2400 IRD 3200
a 2.2 m 2.2 m 2.2 m 2.2 m
b 2.1 m 2.1 m 2.1 m 2.1 m
c (indoors) 1.9 m 2.4 m 2.95 m 3.55 m
d (indoors) approx.
4.0 m
approx.
2
5.1 m
approx.
2
6.2 m
approx.
2
7.5 m
2
c (outdoors) 1.55 m 1.95 m 2.35 m 2.75 m
d (outdoors) approx.
3.3 m
approx.
2
4.1 m
approx.
2
5.0 m
approx.
2
5.8 m
2
Start-up
Info
Odours might arise upon initial start-up or after a
longer period of non-use.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are unrolled completely.
• Make sure that there are no curtains or similar objects in
the immediate vicinity.
Prior to initial start-up, insert the batteries in the remote control.
Connecting the power cable
• Insert the mains plug into a properly secured mains
socket.
• Make sure that the power cable is guided along the back
of the device. Never guide the power cable along the front
of the device!
Operation
Info
The device will only emit heat if the settings are made
via the remote control.
Display
No. Designation Meaning
19 Operating light Flashes red when the device has been
switched on via the on/off switch.
Is permanently illuminated in red when
the device has been switched on via the
remote control.
20 Timer LED Is permanently illuminated in green
when the timer is active.
21 Segment display Heating level indication:
P0 = device in standby mode
P1 = level 1
P2 = level 2
P3 = level 3
Indication of the number of hours during
timer programming
Info
An acoustic signal is emitted each time a setting is
activated.
9 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Remote control
TIMERP3
P2P1
22
23
27
26
24
25
The device settings can only be made using the remote control
included in the scope of delivery.
Therefore, keep the remote control in a safe place, otherwise
the device can no longer be operated. Should you still be unable
to find the remote control, you can reorder a new one from
Trotec.
No. Designation Meaning
22 Transmitter Sends signals to the device.
23 Power button Switching the device on and off
24 P2 button Selecting heating capacity level2
25 TIMER button Timer function
Automatic switch-off in increments of
1hour up to 24hours
26 P3 button Selecting heating capacity level3
27 P1 button Selecting heating capacity level1
The heating capacity in the individual heating levels is 33%
(level1), 66% (level2) and 100% (level3):
Heating
IRD 1200 IRD 1800 IRD 2400 IRD 3200
capacity
P1 = level1 400 W 600 W 800 W 1070 W
P2 = level2 800 W 1200 W 1600 W 2140 W
P3 = level3 1200 W 1800 W 2400 W 3200 W
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
1. Set the on/off switch(2) on the device to I.
ð The operating light(19) flashes.
ð The device is now in standby mode.
2. Press the Power button(23) on the remote control.
ð The segment display(21) indicates P0.
ð The operating light(19) is illuminated.
ð The device is switched on, but does not heat yet.
3. Press the corresponding button(24, 26, 27) on the remote
control to set the desired heating level.
ð The device heats.
ð The selected heating level flashes in the segment
display(21).
ð The operating light(19) is permanently illuminated
during operation.
Setting the timer
The timer allows you to program an automatic switch-off time in
increments of 1hour up to 24hours at any heating level.
You can change the heating level during timer programming.
The timer programming remains activated.
ü The device is switched on.
ü The heating level is set.
1. Press the TIMER button(25) several times to set the
desired number of hours until automatic switch-off.
ð The timer LED(20) is illuminated.
ð The segment display(21) indicates the number of hours
until automatic switch-off.
ð The timer has been programmed and the device will
switch off after the predefined time.
2. In order to delete the setting, select 00 hours using the
TIMER button(25).
ð The segment display(21) indicates the number of
hours 00.
ð The timer has been deleted.
Info
If you switch off the device via the remote control, the
device will be set to standby mode. If standby
operation is not required, you can switch the device off
via the on/off switch(2).
EN 10
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Info
If you switch off the device via the remote control, the
device will be set to standby mode. If standby
operation is not required, you can switch the device off
via the on/off switch(2).
• Switch off the device by pressing the Power button(23) on
the remote control. The operating light flashes. Then set
the on/off switch(2) on the device to 0.
Switch the device off by setting the on/off switch(1) to the
OFFposition.
• Allow the device to cool down completely.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
Errors and faults
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Noise generation (clicking) during switch-on or cooling:
• This is not a fault. The device's metal parts expand when
heated and contract when cooling, and thus generate
noise. It is a perfectly normal process. No measures are
required.
The device does not start:
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device does not emit heat:
• The heating rod might be defective. Have a defective
heating rod replaced by a specialist electrical company.
• Check the heating level on the segment display. If P0 is
displayed, the device is running in standby mode.
Switch the device on by selecting another heating level
between P1 and P3.
• Check the on/off switch. If the on/off switch is set to the
0 position, the device is switched off.
Switch the device on.
• Check the operating light. If the operating light flashes red,
the device is running in standby mode.
Switch on the device by selecting a heating level via the
remote control.
• Contact a specialist electrical company.
The heat output is low:
• Strong wind or cold temperatures in outdoor areas can
impair the device's heat output.
• Check whether the device is installed in the correct
position. The device may be installed too high or the
inclination angle may be incorrect.
• The device is undersized for the area to be heated.
• The heating rod might be defective. Have a defective
heating rod replaced by a specialist electrical company.
RCD or another fuse trips:
• Check the fuse. Switch off any other devices to reduce the
load on the line.
The device slightly vibrates during switch-on and then
stops vibrating:
• Slight vibrations during switch-on are a normal process.
No measures are required.
The device does not respond to the infrared remote control:
• Check whether the distance between remote control and
device is too large and reduce it if necessary.
• Make sure there are no obstacles, such as furniture or
walls, between the device and the remote control. Ensure
visual contact between device and remote control.
• Check the charging status of the batteries and change
them if required.
• If the batteries have only just been changed, check them
for correct polarity and change them if required.
Notice
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
11 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down completely.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the device
Clean the device with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
EN 12
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Technical annex
Technical data
Parameter Value
Model IRD 1200 IRD 1800 IRD 2400 IRD 3200
Heating capacity (level1 /2 /3) 400/ 800/
1200W
600/ 1200/
1800W
800/ 1600/
2400W
1070/ 2140/
3200W
Max. heating capacity 1.2 kW 1.8 kW 2.4 kW 3.2 kW
Nominal current consumption 5.2 A 7.8 A 10.4 A 13.9 A
Power supply 1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
1/N/PE ~ 220–
240V / 50–60Hz
Plug type CEE7/4 CEE 7/4 CEE 7/4 CEE 7/4
Protection class IP55 IP55 IP55 IP55
Dimensions (depth x width x height) 55 x 930x
200mm
55 x 1195x
200mm
55 x 1460x
200mm
55 x 1815x
200mm
Minimum distance to walls and other objects:
top (wall mounting):
top (ceiling mounting):
bottom:
sides:
front:
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
30 cm
19.5 cm
220 cm
20 cm
100 cm
Weight 8 kg 9.5 kg 11.5 kg 13.5 kg
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
13 EN
Operating manual – infrared radiant heater IRD 1200 / IRD 1800 / IRD 2400 / IRD 3200
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
Loading...