IR 1500 S
EN
OPERATING MANUAL
RADIANT HEATER
TRT-BA-IR1500S-TC-002-EN
Table of contents
Notes regarding the operating manual................................. 1
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................4
Assembly and installation.....................................................4
Operation ...............................................................................6
Errors and faults....................................................................6
Maintenance ..........................................................................7
Technical annex.....................................................................7
Declaration of conformity .....................................................9
Notes regarding the operating manual
Symbols
Danger from electric current
Warns about hazards from electric current which can
lead to injuries or even death.
Caution
Indicates situations with a possible fire hazard.
Danger
Warns of a hazard which can lead to personal injury.
Caution
Warns of a hazard which can lead to property damage.
The current version of the operating manual can be found at:
Legal notice
This release replaces all previous versions. No part of this
publication may be reproduced without written permission from
TrotecGmbH&Co.KG. The same applies for electronically
processing, duplicating or spreading the publication.
Subject to technical changes. All rights reserved. Trademarks
are used without guarantee that they may be used freely and
primarily following the spelling of the manufacturer. Product
names are registered.
Changes to construction in the interests of constant
improvements to the product, as well as changes to the shape
and colour are reserved.
The scope of delivery may vary from product images. This
document was created with all due care. TrotecGmbH&Co.KG
accepts no liability whatsoever for possible mistakes or
omissions.
© TrotecGmbH&Co.KG
Warranty and liability
The device complies with the fundamental health and safety
requirements of the applicable EU regulations and was tested
at the factory for perfect functionality multiple times.
When making a warranty claim, supply the device number
(see the rear of the device).
When manufacturer's instructions or legal regulations have
not been followed, or after unauthorised changes to the device
are made, the manufacturer is not responsible for the resulting
damages. Changes to the device or unauthorised replacement
of individual parts can drastically impact the electrical safety
of this product and will result in the loss of the warranty.
Liability does not extend to damages to people or property
caused by the device being used other than as described
in the instructions in this operating manual.
Subject to changes to technical design and model changes as
part of constant development and product improvement without
prior notice.
No liability is accepted for damages resulting from improper
use. In such a case, any warranty claims will be voided also.
IR 1500 S
http://download.trotec.com/?sku=1410003101&id=1
1 EN
Operating manual – radiant heater IR 1500 S
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Let the device dry out after a wet clean. Do not operate
it when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device
if you detect damages on the mains plug or power cable.
Defective power cables pose a serious health risk.
• Observe the storage and operating conditions (see chapter
Technical data).
• Do not transport the device during operation.
• Allow the device to cool down before transport and/ or
maintenance work.
Intended use
Only use the device IR 1500 S for heating surfaces in interior
spaces or in roofed outdoor areas protected from weather
effects.
Intended use comprises:
• Heating surfaces
– in living spaces,
– in storage facilities,
– in salesrooms,
– in construction areas,
– in containers,
– in bathrooms,
– on changing tables,
– in roofed outdoor areas (e.g. covered terraces).
Improper use
The device is not intended for industrial use.
• Do not place any objects, e.g. clothing, on the device.
• The device may not be used for heating vehicles.
• The device may not be used as a heating device for
babies / children or animals.
• The device may not be installed inside a shower or directly
above a bathtub.
• The device may not be used near swimming pools.
• The device may not be used in the immediate vicinity
of sinks, bathtubs or other water containers.
• Do not expose the device to moisture or weather effects
(rain, sunlight).
• The device must not be mounted to the ceiling.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Any unauthorised changes, modifications or alterations
to the device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
EN 2
Operating manual – radiant heater IR 1500 S
Residual risks
Danger from electric current
Work on the electrical components must only be
carried out by an electrically skilled person or an
authorised specialist company.
Danger from electric current
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Danger
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Danger
The device is not a toy and does not belong in the
hands of children.
Danger
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Behaviour in the event of an emergency
1. In an emergency, disconnect the device from the mains
feed-in: Switch the device off and disconnect the power
cable from the mains socket. Hold onto the mains plug
while doing so.
2. Do not reconnect a defective device to the mains.
Danger
Risk of injury due to infrared radiation!
Do not stay in the device's immediate vicinity for too
long. Do not look directly into the device for too long.
Observe the minimum distances from the device.
Danger
Improper installation entails a risk of fire.
Danger
In order to avoid overheating and fire hazards,
the heater must not be covered.
Danger
Coarse dirt particles on the heating rods can cause
the device to overheat. Fire hazard.
Remove coarse dirt particles from the heating rods
according to the Maintenance chapter before switching
on the device.
3 EN
Operating manual – radiant heater IR 1500 S
Information about the device
00
1121
567
3
4
3
Transport and storage
Description of the device
The device IR 1500 S is used to quickly generate instant heat.
The device is based on the functional principle of heat
generation by infrared radiation. Persons or objects are heated
directly.
• suitable for wet rooms
• splash-proof IP24
• only suitable for wall mounting
• adjustable angle
• no dust circulation (suitable for allergy sufferers)
Device depiction
Transport
Before transporting the device, proceed as follows:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down sufficiently.
Storage
Before storing the device, proceed as follows:
• Allow the device to cool down sufficiently.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat.
• protected from dust and direct sunlight.
• with a cover to protect it from invasive dust, if necessary.
• Remove the batteries from the device.
• Place no further devices or objects on top of the device
to prevent it from being damaged.
Assembly and installation
No. Designation
1 Heating rods
2 Heating level indicator:
0 = off
1 = level 1 (500 W)
2 = level 2 (1000 W)
3 = level 3 (1500 W)
3 Warning label (device must not be covered)
4 Pull switch with cord
5 Bracket for wall mounting
6 Swivelling bracket
7 Power cable
Scope of delivery
• 1 x Radiant heater
• 4 x Fastening screws
• 1 x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
The device is only suited for wall mounting. Observe the
following requirement for installation inside a room:
Danger
Risk of fire due to improper installation!
There is a risk of fire if the required minimum
distances are not observed.
The device must be positioned at a distance of at least
180cm from the floor and at least 50cm from walls
and other objects such as curtains or sockets.
EN 4
Operating manual – radiant heater IR 1500 S
Installation
00
50 cm
50 cm
180 cm
50 cm
00
00
117 mm
41 mm
20° - 40°
When installing the device, observe the minimum distances
from walls and other objects as described in the Technical data
chapter.
• Minimum distance of 180cm from the floor.
• Minimum distance of 50cm from walls or other objects.
• For installation in bathrooms or washing rooms, observe
the national regulations on safety distances.
• Do not install the device at the ceiling or directly behind
a door.
• Never install the device in a way that it radiates directly
onto walls or other objects.
• Only install the device in a horizontal position.
1. Mark the drill holes on the wall according to the following
pattern:
2. Drill the holes into the wall at the marked positions.
3. Insert suitable dowels into the bore holes.
4. Insert the screws into the dowels and fasten the screws.
ð The screws should protrude approx. 0.5cm from the
dowels.
5. Hang the device in.
6. Check whether all 4 screws are hooked into the bracket.
7. Tilt the device to the desired angle. Ideally, the inclination
angle should be between 20° and 40°.
The following is required for installation:
• a pencil for marking the drill holes
• a tape measure for determining the distances
• a suitable drill
• dowels appropriate for the structure of the wall
• a screwdriver
• a spirit level
5 EN
Operating manual – radiant heater IR 1500 S
Start-up
Note:
Odours might arise upon initial start-up or after a longer period
of non-use.
• Check whether the power cable is intact. If the power
cable is damaged, it must be replaced by the
manufacturer, his customer service or similarly qualified
personnel.
• Do not create tripping hazards when laying the power
cable or other electrical cables. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• Make sure that there are no curtains or similar in the
immediate vicinity.
• Insert the mains plug into a properly secured mains
socket.
– Make sure that the power cable is guided along the
back of the device. Never guide the power cable along
the front of the device!
Operation
Switching the device on
Once you have completely installed the device as described
in the Start-up chapter, you can switch it on.
1. Adjust the device position with the swivelling bracket.
2. Pull the cord of the pull switch (4) until the desired heating
level appears on the heating level indicator(2):
level 0 = device switched off
level 1 = 500W
level 2 = 1000W
level 3 = 1500W
Shutdown
Danger
Do not touch the mains plug with wet or damp hands.
• Set the pull switch(4) to 0.
• Allow the device to cool down completely.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Clean the device according to the Maintenance and
cleaning chapter.
• Store the device according to the Storage chapter.
Errors and faults
Danger
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
• Check the power connection.
• Check the mains plug for damages.
• Wait for 10 minutes before restarting the device.
If the device is not starting, have the electrics checked by
a specialist company or by Trotec.
The device does not emit heat:
• Check the heating level indicator(2). If it is set to 0,
the device is switched off.
Switch the device on by selecting another heating level
between 1 and 3.
RCD or another fuse trips:
• Check the fuse. Switch off any other devices to reduce
the load on the line.
The device slightly vibrates during switch-on and then
stops vibrating:
• Slight vibrations during switch-on are a normal process.
No measures are required.
Note:
Wait for at least 3 minutes after maintenance and repair work.
Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
EN 6
Operating manual – radiant heater IR 1500 S
Maintenance
1
2
L
N
PE
Switch
Quar tz tube
3
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down completely.
Cleaning the device
Danger
Never immerse the device in water!
Caution
Do not touch the reflector or the heating rods with bare
hands.
Clean the housing with a soft, damp and lint-free cloth.
Ensure that no moisture enters the housing. Do not use any
aggressive cleaning agents such as cleaning sprays, solvents,
alcohol-based or abrasive cleaners to dampen the cloth.
Wipe the housing dry after cleaning.
Dirt on the heating rods should be removed with a long brush
with soft bristles.
Wiring diagram
Technical annex
Technical data
Parameter Value
Model IR 1500 S
Heating capacity (W) 500 / 1000 / 1500
Mains connection 1/N/PE ~ 230 V / 50 Hz
Nominal current (A) 6.5
Weight (kg) 1.80
Dimensions
(length x width x height in mm)
Plug type CEE 7/7
Protection class IP 24
Distances to walls / other objects
above 50 cm
below 180 cm
to the front 50 cm
to the sides 50 cm
120 x 560 x 163
7 EN
Operating manual – radiant heater IR 1500 S
Spare parts drawing and list
Note!
The position numbers of the spare parts differ from those
describing the positions of other parts mentioned in this
operating manual.
No. Spare part No. Spare part No. Spare part
1 Display window 7 Pull switch 13 Wall mount casing
2 Front cover 8 Back cover 14 Wall mount panel
3 Tube bracket 9 Vacillation support 15 Wall mount panel
4 Quartz tube 10 Connection cover 16 Power cord and plug
5 Reflect panel 11 Water proof panel
6 Knob 12 Wire fix bracket
Disposal
In the European Union, electronic equipment must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2012/19/EU of the
European Parliament and of the Council of 4 July 2012 on waste
electrical and electronic equipment (WEEE). At the end of its life,
please dispose of this device according to the valid legal
requirements.
EN 8
Operating manual – radiant heater IR 1500 S
Declaration of conformity
in accordance with the EU Low Voltage Directive 2014/35/EU
and the EU Directive 2014/30/EU relating to electromagnetic
compatibility.
Herewith, we declare that the device IR 1500 S was developed,
constructed and produced in compliance with the named
EU directives.
Applied standards:
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2013
EN 60335-2-30:2009+A11:2012
EN 60335-1:2012+A11:2014
EN 62233:2008
marking is found on the rear of the device.
The
Manufacturer:
Trotec GmbH & Co. KG
Grebbener Straße 7
D-52525 Heinsberg
Phone: +49 2452 962-400
Fax: +49 2452 962-200
E-mail: info@trotec.com
Heinsberg, 29.01.2016
Detlef von der Lieck
Managing Director
9 EN
Operating manual – radiant heater IR 1500 S
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
Loading...